epd-gde021a1 0.2.1

An embedded-hal based driver for ePaper displays with chip: GDE021A1 (172x72 B/W via SPI)
Documentation 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115

//! This example works on STM32L051R8 Discovery Evaluation board.
//! The STM32L053R8 Discovery board is equipped with Cortex-M0 MCU.
//!
//! Set the default compile target in e.g *.cargo/config* file like
//! ```config
//! [build]
//! target = "thumbv6m-none-eabi"    # Cortex-M0 and Cortex-M0+
//! ```
//!
//! or build with target flag.
//! ```
//! cargo build --target=thumbv6m-none-eabi --example display
//! ```


#![no_main]
#![no_std]

use panic_semihosting as _;
use cortex_m_semihosting::hprintln;

use cortex_m_rt::entry;
use stm32l0xx_hal::{
    pac,
    gpio::*,
    prelude::*,
    spi::*,
    rcc::{Config,RccExt},
};

use epd_gde021a1;

extern crate embedded_graphics;
use embedded_graphics::{
    pixelcolor::{BinaryColor, Gray2},
    style::{PrimitiveStyle, TextStyle},
    primitives::Circle,
    fonts::{Font6x8, Text},
    prelude::*,
};

use epd_gde021a1::GDE021A1;

#[entry]
fn main() -> ! {
    hprintln!("** Start").unwrap();
    let dp = pac::Peripherals::take().unwrap();
    let cp = cortex_m::Peripherals::take().unwrap();

    // Configure the clock.
    let mut rcc = dp.RCC.freeze(Config::hsi16());

    // Acquire the GPIOx peripheral.
    // This also enables the clock for GPIOx in the RCC register.
    let gpioa = dp.GPIOA.split(&mut rcc);
    let gpiob = dp.GPIOB.split(&mut rcc);

    // The GPIO's
    let chip_sel = gpioa.pa15.into_push_pull_output();
    let data_cmd = gpiob.pb11.into_push_pull_output();
    let reset = gpiob.pb2.into_push_pull_output();
    let busy = gpiob.pb8.into_pull_up_input();
    let mut power = gpiob.pb10.into_push_pull_output();

    // The SPI
    let mosi = gpiob.pb5;
    let clk = gpiob.pb3;
    let spi = dp.SPI1.spi((clk, NoMiso, mosi),
                            MODE_0, 1_000_000.hz(), &mut rcc);

    // the time delay
    let mut delay = cp.SYST.delay(rcc.clocks);

    // and finally the display structure
    let mut disp =  GDE021A1::new(spi, reset, Some(chip_sel), data_cmd, busy);

    hprintln!("** All config done ").unwrap();

    hprintln!("** Power on the on the display").unwrap();
    power.set_low().unwrap();

    hprintln!("** Initialize the display").unwrap();
    disp.init(&mut delay).expect("could not init display");
    // disp.alt_init(&mut delay).expect("could not init display");

    hprintln!("** Draw/write on display (RAM cache)").unwrap();
    disp.clear();

    // draw some fancy stuff
    let elem =  Circle::new(Point::new(140, 36), 25)
         .into_styled(PrimitiveStyle::with_fill(Gray2::new(0b10)));
    elem.draw(&mut disp).unwrap();

    // Draw some text
    let elem = Text::new("Power minimized ", Point::new(1, 8))
        .into_styled(TextStyle::new(Font6x8, BinaryColor::On));
    elem.draw(&mut disp).unwrap();
    let elem = Text::new("and safely", Point::new(1, 20))
        .into_styled(TextStyle::new(Font6x8, BinaryColor::On));
        elem.draw(&mut disp).unwrap();
    let elem = Text::new("implemented in", Point::new(1, 32))
        .into_styled(TextStyle::new(Font6x8, BinaryColor::On));
    elem.draw(&mut disp).unwrap();
    let elem = Text::new("Rust", Point::new(1, 44))
        .into_styled(TextStyle::new(Font6x8, BinaryColor::On));
    elem.draw(&mut disp).unwrap();

    hprintln!("** Refresh the display").unwrap();
    disp.refresh(&mut delay).expect("Could not refresh display");

    hprintln!("** Enter the main loop").unwrap();
    loop {
        continue;
    }
}