brepkit-operations 3.2.36

CAD modeling operations (booleans, fillets, extrusions) for brepkit
Documentation 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163

//! #1538 coplanar-interface family: cutting a through-hole out of a plate and
//! fusing the plate onto a block across the shared plane must produce strictly
//! valid winding (the free/over census cannot see same-direction shared
//! edges; only `validate_solid`'s orientation check can).
//!
//! Four winding emitters have failed here, each invisible to watertightness:
//! - the internal-loops splitter normalized disc/hole loops with a signed
//!   area taken in the surface's own parameterization, which inverts the
//!   verdict on a down-facing plane (fixed: local-frame areas);
//! - `merge_duplicate_edges` never flipped closed edges, silently reversing
//!   winding when two coincident circles parameterize opposite ways (fixed:
//!   tangent comparison at the shared point — parameter-frame evaluation is
//!   NOT valid for closed curves, whose domains anchor at their own
//!   reference directions);
//! - `rebuild_face_with_cb_edges` degenerated to `forward=true` for a closed
//!   rim replaced by its CommonBlock circle (fixed: same comparison);
//! - `extrude` compensated a CW-wound profile by flipping surface normals
//!   while emitting the mirrored wires as-is, so every face's wire wound
//!   against its flags — valid to the pairwise-opposition check, but the
//!   face splitter trusts effective wire winding and mints same-direction
//!   rim arcs in any later boolean (fixed: profile wires are rewound
//!   up front).

#![allow(clippy::unwrap_used, clippy::expect_used)]

use brepkit_math::mat::Mat4;
use brepkit_operations::boolean::{self, BooleanOp};
use brepkit_topology::Topology;
use brepkit_topology::solid::SolidId;

fn plate_and_block(topo: &mut Topology) -> (SolidId, SolidId) {
    let plate = brepkit_operations::primitives::make_box(topo, 80.0, 80.0, 5.0).unwrap();
    brepkit_operations::transform::transform_solid(topo, plate, &Mat4::translation(0.0, 0.0, 5.0))
        .unwrap();
    let block = brepkit_operations::primitives::make_box(topo, 80.0, 80.0, 5.0).unwrap();
    (plate, block)
}

fn assert_strictly_valid(topo: &Topology, sid: SolidId, label: &str) {
    let report = brepkit_operations::validate::validate_solid(topo, sid).unwrap();
    assert!(report.is_valid(), "{label} must validate: {report:?}");
}

#[test]
fn rect_through_hole_cut_and_interface_fuse_have_valid_winding() {
    let mut topo = Topology::new();
    let (plate, block) = plate_and_block(&mut topo);
    let hole = brepkit_operations::primitives::make_box(&mut topo, 20.0, 20.0, 7.0).unwrap();
    brepkit_operations::transform::transform_solid(
        &mut topo,
        hole,
        &Mat4::translation(30.0, 30.0, 4.0),
    )
    .unwrap();
    let holed = boolean::boolean(&mut topo, BooleanOp::Cut, plate, hole).unwrap();
    assert_strictly_valid(&topo, holed, "rect through-hole cut");

    let fused = boolean::boolean(&mut topo, BooleanOp::Fuse, holed, block).unwrap();
    assert_strictly_valid(&topo, fused, "rect interface fuse");
    let vol = brepkit_operations::measure::oriented_solid_volume(&topo, fused, 0.05).unwrap();
    assert!((vol - 62000.0).abs() < 0.5, "fuse volume {vol:.3}");
}

#[test]
fn circle_through_hole_cut_and_interface_fuse_have_valid_winding() {
    let mut topo = Topology::new();
    let (plate, block) = plate_and_block(&mut topo);
    let hole = brepkit_operations::primitives::make_cylinder(&mut topo, 10.0, 7.0).unwrap();
    brepkit_operations::transform::transform_solid(
        &mut topo,
        hole,
        &Mat4::translation(40.0, 40.0, 4.0),
    )
    .unwrap();
    let holed = boolean::boolean(&mut topo, BooleanOp::Cut, plate, hole).unwrap();
    assert_strictly_valid(&topo, holed, "circle through-hole cut");

    let fused = boolean::boolean(&mut topo, BooleanOp::Fuse, holed, block).unwrap();
    assert_strictly_valid(&topo, fused, "circle interface fuse");
}

/// A cutter whose bottom cap is COINCIDENT with the plate's bottom plane
/// (the circle-insert cutDepth == floor configuration). The kept band's
/// original rim merges with the section circle parameterized the other way;
/// the direction map must come from tangents at the shared point, not from
/// parameter-frame evaluation (a closed circle's domain anchors at its own
/// reference direction).
#[test]
fn coincident_cap_pocket_cut_has_valid_winding() {
    let mut topo = Topology::new();
    let (plate, _block) = plate_and_block(&mut topo);
    let hole = brepkit_operations::primitives::make_cylinder(&mut topo, 10.0, 6.0).unwrap();
    brepkit_operations::transform::transform_solid(
        &mut topo,
        hole,
        &Mat4::translation(40.0, 40.0, 5.0),
    )
    .unwrap();
    let holed = boolean::boolean(&mut topo, BooleanOp::Cut, plate, hole).unwrap();
    assert_strictly_valid(&topo, holed, "coincident-cap pocket cut");
}

/// A CW-wound 4-arc circle profile (the way the layout tool's extruded
/// insert profiles arrive) extruded into the coincident-cap cutter of
/// `coincident_cap_pocket_cut_has_valid_winding`. Extrude must rewind the
/// profile: compensating with flipped surface normals leaves every wire
/// winding against its face flags, and the cut then mints eight
/// same-direction rim arcs (the captured circle-insert floor cut).
#[test]
fn cw_wound_extruded_profile_cut_has_valid_winding() {
    use brepkit_math::curves::Circle3D;
    use brepkit_math::vec::{Point3, Vec3};
    use brepkit_topology::edge::{Edge, EdgeCurve};
    use brepkit_topology::face::{Face, FaceSurface};
    use brepkit_topology::vertex::Vertex;
    use brepkit_topology::wire::{OrientedEdge, Wire};

    let mut topo = Topology::new();
    let (plate, block) = plate_and_block(&mut topo);

    let (cx, cy, r, z0) = (40.0, 40.0, 10.0, 5.0);
    let z = Vec3::new(0.0, 0.0, 1.0);
    let v = |topo: &mut Topology, x: f64, y: f64| {
        topo.add_vertex(Vertex::new(Point3::new(x, y, z0), 1e-7))
    };
    let v0 = v(&mut topo, cx + r, cy);
    let v1 = v(&mut topo, cx, cy + r);
    let v2 = v(&mut topo, cx - r, cy);
    let v3 = v(&mut topo, cx, cy - r);
    let arc = |topo: &mut Topology, a, b| {
        let circle = Circle3D::new(Point3::new(cx, cy, z0), z, r).unwrap();
        topo.add_edge(Edge::new(a, b, EdgeCurve::Circle(circle)))
    };
    let edges = [
        arc(&mut topo, v0, v1),
        arc(&mut topo, v1, v2),
        arc(&mut topo, v2, v3),
        arc(&mut topo, v3, v0),
    ];
    // CW traversal of CCW-stored arcs: v0 -> v3 -> v2 -> v1 -> v0.
    let oes: Vec<OrientedEdge> = edges
        .iter()
        .rev()
        .map(|&e| OrientedEdge::new(e, false))
        .collect();
    let wid = topo.add_wire(Wire::new(oes, true).unwrap());
    let fid = topo.add_face(Face::new(
        wid,
        vec![],
        FaceSurface::Plane {
            normal: Vec3::new(0.0, 0.0, 1.0),
            d: z0,
        },
    ));
    let hole = brepkit_operations::extrude::extrude(&mut topo, fid, z, 6.0).unwrap();
    assert_strictly_valid(&topo, hole, "cw-profile extruded tool");

    let holed = boolean::boolean(&mut topo, BooleanOp::Cut, plate, hole).unwrap();
    assert_strictly_valid(&topo, holed, "cw-profile coincident-cap cut");

    let fused = boolean::boolean(&mut topo, BooleanOp::Fuse, holed, block).unwrap();
    assert_strictly_valid(&topo, fused, "cw-profile interface fuse");
}