as7265x 0.1.0

#![no_std]

#[cfg(feature = "sync")]
use embedded_hal::{
    delay::DelayNs,
    i2c::{self},
};

#[cfg(not(feature = "sync"))]
use embedded_hal_async::{
    delay::DelayNs,
    i2c::{self},
};
use maybe_async::maybe_async;

const AS7265X_ADDR: u8 = 0x49;
const STATUS_REG: u8 = 0x00;
const WRITE_REG: u8 = 0x01;
const READ_REG: u8 = 0x02;

const TX_VALID: u8 = 0x02;
const RX_VALID: u8 = 0x01;

const HW_VERSION_HIGH_ADDR: u8 = 0x00;
const HW_VERSION_LOW_ADDR: u8 = 0x01;
const FW_VERSION_HIGH_ADDR: u8 = 0x02;
const FW_VERSION_LOW_ADDR: u8 = 0x03;
const CONFIG_ADDR: u8 = 0x04;
const INTEGRATION_ADDR: u8 = 0x05;
const TEMP_ADDR: u8 = 0x06;
const LED_ADDR: u8 = 0x07;
const DEV_SELECT_ADDR: u8 = 0x4F;

const SOFT_RESET: u8 = 0b10000000;
const ENABLE_INTERRUPT: u8 = 0b01000000;

const CONFIG_GAIN_MASK: u8 = 0x30;
const CONFIG_GAIN_SHIFT: u8 = 4;
const CONFIG_BANK_MASK: u8 = 0x0C;
const CONFIG_BANK_SHIFT: u8 = 2;
const CONFIG_DATA_RDY: u8 = 0x02;

const LED_DRV_ICL_MASK: u8 = 0x30;
const LED_DRV_ICL_SHIFT: u8 = 4;
const LED_DRV_ENABLE: u8 = 0x08;
const LED_IND_ICL_MASK: u8 = 0x06;
const LED_IND_ICL_SHIFT: u8 = 1;
const LED_IND_ENABLE: u8 = 0x01;

#[derive(Debug, Clone, Copy)]
pub enum Channel {
    /// 410nm - AS72653
    A,
    /// 435nm - AS72653
    B,
    /// 460nm - AS72653
    C,
    /// 485nm - AS72653
    D,
    /// 510nm - AS72653
    E,
    /// 535nm - AS72653
    F,
    /// 560nm - AS72652
    G,
    /// 585nm - AS72652
    H,
    /// 610nm - AS72651
    R,
    /// 645nm - AS72652
    I,
    /// 680nm - AS72651
    S,
    /// 705nm - AS72652
    J,
    /// 730nm - AS72651
    T,
    /// 760nm - AS72651
    U,
    /// 810nm - AS72651
    V,
    /// 860nm - AS72651
    W,
    /// 900nm - AS72652
    K,
    /// 940nm - AS72652
    L,
}

impl Channel {
    /// Each channel is only read from one of three sensors
    pub fn get_device_for_channel(&self) -> Device {
        match self {
            Channel::A | Channel::B | Channel::C | Channel::D | Channel::E | Channel::F => {
                Device::Uv
            }
            Channel::G | Channel::H | Channel::I | Channel::J | Channel::K | Channel::L => {
                Device::Visable
            }
            Channel::R | Channel::S | Channel::T | Channel::U | Channel::V | Channel::W => {
                Device::Nir
            }
        }
    }

    /// Get the virtual register address for the raw value of the channel
    fn get_raw_address(&self) -> u8 {
        match self {
            Channel::A | Channel::G | Channel::R => 0x08,
            Channel::B | Channel::H | Channel::S => 0x0A,
            Channel::C | Channel::I | Channel::T => 0x0C,
            Channel::D | Channel::J | Channel::U => 0x0E,
            Channel::E | Channel::K | Channel::V => 0x10,
            Channel::F | Channel::L | Channel::W => 0x12,
        }
    }

    /// Get the virtual register address for the calibrated value of the channel
    fn get_cal_address(&self) -> u8 {
        let raw = self.get_raw_address();
        ((raw - 0x08) / 2) * 4 + 0x14
    }
}

/// The AS7265X has three sensor devices
#[derive(Debug, Clone, Copy)]
pub enum Device {
    Visable = 0x00,
    Nir = 0x01,
    Uv = 0x02,
}

/// The three main LEDs on the device
#[derive(Debug, Clone, Copy)]
pub enum Led {
    White,
    Ir,
    Uv,
}

impl Led {
    /// Apparently the LEDs don't match the device the are for
    fn get_device(&self) -> Device {
        match self {
            Led::White => Device::Nir,
            Led::Ir => Device::Visable,
            Led::Uv => Device::Uv,
        }
    }
}

#[derive(Debug, Clone, Copy)]
pub enum GainConfig {
    /// x1
    Gain1x,

    /// x3.7
    Gain3_7x,

    /// x16
    Gain16x,

    /// x64
    Gain64x,
}

impl GainConfig {
    /// To byte that can be written to the virtual register
    fn to_byte(self) -> u8 {
        match self {
            GainConfig::Gain1x => 0b00,
            GainConfig::Gain3_7x => 0b01,
            GainConfig::Gain16x => 0b10,
            GainConfig::Gain64x => 0b11,
        }
    }
}

#[derive(Debug, Clone, Copy)]
pub enum MeasurementMode {
    /// 4 channels
    Mode0,

    /// 4 channels
    Mode1,

    /// All 6 channels
    Mode2Continuous,

    /// One-Shot operation of mode 2
    Mode3OneShot,
}

impl MeasurementMode {
    /// To byte that can be written to the virtual register
    fn to_byte(self) -> u8 {
        match self {
            MeasurementMode::Mode0 => 0b00,
            MeasurementMode::Mode1 => 0b01,
            MeasurementMode::Mode2Continuous => 0b10,
            MeasurementMode::Mode3OneShot => 0b11,
        }
    }
}

#[derive(Debug, Clone)]
pub struct AS7265XConfig {
    /// Enable the onboard interrupt pin
    pub enable_interrupt: bool,
    pub gain: GainConfig,
    pub measurement_mode: MeasurementMode,
    /// Integration time: value * 2.8ms
    pub integration_time: u8,
}

impl Default for AS7265XConfig {
    fn default() -> Self {
        Self {
            enable_interrupt: true,
            gain: GainConfig::Gain64x,
            measurement_mode: MeasurementMode::Mode3OneShot,
            integration_time: 49,
        }
    }
}

impl AS7265XConfig {
    /// Convert to byte to write to the config virtual register
    fn to_byte(&self) -> u8 {
        let mut byte = 0u8;

        if self.enable_interrupt {
            byte |= ENABLE_INTERRUPT;
        }

        byte |= (self.gain.to_byte() << CONFIG_GAIN_SHIFT) & CONFIG_GAIN_MASK;
        byte |= (self.measurement_mode.to_byte() << CONFIG_BANK_SHIFT) & CONFIG_BANK_MASK;

        byte
    }
}

#[derive(Debug, Clone, Copy)]
pub enum LedDriverCurrent {
    /// 12.5 mA
    Ma12_5,
    /// 25 mA
    Ma25,
    /// 50 mA
    Ma50,
    /// 100 mA
    Ma100,
}

impl LedDriverCurrent {
    fn to_bits(self) -> u8 {
        match self {
            LedDriverCurrent::Ma12_5 => 0b00,
            LedDriverCurrent::Ma25 => 0b01,
            LedDriverCurrent::Ma50 => 0b10,
            LedDriverCurrent::Ma100 => 0b11,
        }
    }
}

#[derive(Debug, Clone, Copy)]
pub enum LedIndicatorCurrent {
    /// 1 mA
    Ma1,
    /// 2 mA
    Ma2,
    /// 4 mA
    Ma4,
    /// 8 mA
    Ma8,
}

impl LedIndicatorCurrent {
    fn to_bits(self) -> u8 {
        match self {
            LedIndicatorCurrent::Ma1 => 0b00,
            LedIndicatorCurrent::Ma2 => 0b01,
            LedIndicatorCurrent::Ma4 => 0b10,
            LedIndicatorCurrent::Ma8 => 0b11,
        }
    }
}

#[derive(Debug, Clone, Copy)]
pub struct LedConfig {
    pub drv_enabled: bool,
    pub drv_current: LedDriverCurrent,
    pub ind_enabled: bool,
    pub ind_current: LedIndicatorCurrent,
}

impl LedConfig {
    /// To byte that can be written to the virtual register
    fn to_byte(self) -> u8 {
        let mut byte = 0u8;

        if self.drv_enabled {
            byte |= LED_DRV_ENABLE;
        }
        byte |= (self.drv_current.to_bits() << LED_DRV_ICL_SHIFT) & LED_DRV_ICL_MASK;

        if self.ind_enabled {
            byte |= LED_IND_ENABLE;
        }
        byte |= (self.ind_current.to_bits() << LED_IND_ICL_SHIFT) & LED_IND_ICL_MASK;

        byte
    }
}

impl Default for LedConfig {
    fn default() -> Self {
        Self {
            drv_enabled: false,
            drv_current: LedDriverCurrent::Ma12_5,
            ind_enabled: false,
            ind_current: LedIndicatorCurrent::Ma8,
        }
    }
}

#[derive(Debug)]
pub enum Error<E> {
    I2c(E),
    Timeout,
}

impl<E> From<E> for Error<E> {
    fn from(e: E) -> Self {
        Error::I2c(e)
    }
}

/// The AS7265X device
pub struct AS7265X<I, D>
where
    I: i2c::I2c,
    D: DelayNs,
{
    device: I,
    delay: D,
    config: AS7265XConfig,
}

#[maybe_async]
impl<I, D> AS7265X<I, D>
where
    I: i2c::I2c,
    D: DelayNs,
{
    /// Create a new AS7265X device
    pub fn new(device: I, config: AS7265XConfig, delay: D) -> Self {
        Self {
            device,
            config,
            delay,
        }
    }

    /// Initialize the device.
    /// Writes config, integration time and led config.
    /// Ok to call multiple times & most likly not need but the cpp driver also does this.
    #[maybe_async]
    pub async fn init(&mut self) -> Result<(), Error<I::Error>> {
        self.write_config().await?;

        self.set_integration_time(self.config.integration_time)
            .await?;

        self.set_led_config(
            Led::White,
            LedConfig {
                ..Default::default()
            },
        )
        .await?;

        self.set_led_config(
            Led::Ir,
            LedConfig {
                ..Default::default()
            },
        )
        .await?;

        self.set_led_config(
            Led::Uv,
            LedConfig {
                ..Default::default()
            },
        )
        .await?;

        Ok(())
    }

    /// Perform a soft reset
    #[maybe_async]
    pub async fn soft_reset(&mut self) -> Result<(), Error<I::Error>> {
        self.write_virtual_register(CONFIG_ADDR, SOFT_RESET).await?;
        self.delay.delay_ms(100).await;
        Ok(())
    }

    /// Write the config to the device
    /// Also need to fire the oneshot mode again
    #[maybe_async]
    async fn write_config(&mut self) -> Result<(), Error<I::Error>> {
        let config_byte = self.config.to_byte();
        self.write_virtual_register(CONFIG_ADDR, config_byte).await
    }

    /// Sets the integration time value
    /// value * 2.8ms
    #[maybe_async]
    pub async fn set_integration_time(&mut self, time: u8) -> Result<(), Error<I::Error>> {
        self.config.integration_time = time;
        self.write_virtual_register(INTEGRATION_ADDR, time).await
    }

    /// Write the LED specific config
    #[maybe_async]
    async fn set_led_config(&mut self, led: Led, config: LedConfig) -> Result<(), Error<I::Error>> {
        self.select_device(led.get_device()).await?;
        let config_byte = config.to_byte();
        self.write_virtual_register(LED_ADDR, config_byte).await
    }

    /// Get the hardware info from the hw version register
    #[maybe_async]
    pub async fn get_device_type(&mut self) -> Result<u8, Error<I::Error>> {
        self.read_virtual_register(HW_VERSION_HIGH_ADDR).await
    }

    /// Get the hardware info from the hw version register
    #[maybe_async]
    pub async fn get_hardware_version(&mut self) -> Result<u8, Error<I::Error>> {
        self.read_virtual_register(HW_VERSION_LOW_ADDR).await
    }

    /// Alot of function only work if you have the correct device selected
    #[maybe_async]
    async fn select_device(&mut self, device: Device) -> Result<(), Error<I::Error>> {
        self.write_virtual_register(DEV_SELECT_ADDR, device as u8)
            .await
    }

    /// Read the integrated temperature sensor in °C
    #[maybe_async]
    pub async fn read_temperature(&mut self) -> Result<i8, Error<I::Error>> {
        let temp = self.read_virtual_register(TEMP_ADDR).await?;
        Ok(temp as i8)
    }

    /// Check if the internal register reports data ready
    #[maybe_async]
    pub async fn is_data_ready(&mut self) -> Result<bool, Error<I::Error>> {
        let config = self.read_virtual_register(CONFIG_ADDR).await?;
        Ok((config & CONFIG_DATA_RDY) != 0)
    }

    /// Run a messurement
    /// Only needed if messurement mode is set to One-Shot
    /// Basicly rewrites the config and waits the current integration time
    #[maybe_async]
    pub async fn measure(&mut self) -> Result<(), Error<I::Error>> {
        self.write_config().await?;
        let wait_time = (self.config.integration_time as u32) * 28 / 10 * 2;
        self.delay.delay_ms(wait_time).await;
        Ok(())
    }

    /// Same as measure but enable LED befor and disable after
    #[maybe_async]
    pub async fn mesure_with_bulb(&mut self) -> Result<(), Error<I::Error>> {
        self.set_led_config(
            Led::White,
            LedConfig {
                drv_enabled: true,
                ..Default::default()
            },
        )
        .await?;

        self.set_led_config(
            Led::Ir,
            LedConfig {
                drv_enabled: true,
                ..Default::default()
            },
        )
        .await?;

        self.set_led_config(
            Led::Uv,
            LedConfig {
                drv_enabled: true,
                ..Default::default()
            },
        )
        .await?;

        self.measure().await?;

        self.set_led_config(
            Led::White,
            LedConfig {
                ..Default::default()
            },
        )
        .await?;

        self.set_led_config(
            Led::Ir,
            LedConfig {
                ..Default::default()
            },
        )
        .await?;

        self.set_led_config(
            Led::Uv,
            LedConfig {
                ..Default::default()
            },
        )
        .await?;

        Ok(())
    }

    /// Read the raw value for a channel
    #[maybe_async]
    pub async fn read_raw_measurement(&mut self, channel: Channel) -> Result<u16, Error<I::Error>> {
        let dev = channel.get_device_for_channel();
        self.select_device(dev).await?;
        self.read_raw_channel(channel.get_raw_address()).await
    }

    /// Read the calibrated value for a channel
    #[maybe_async]
    pub async fn read_calibrated_messurement(
        &mut self,
        channel: Channel,
    ) -> Result<f32, Error<I::Error>> {
        let dev = channel.get_device_for_channel();
        self.select_device(dev).await?;

        self.read_calibrated_channel(channel.get_cal_address())
            .await
    }

    /// Read u16 value from address
    #[maybe_async]
    async fn read_raw_channel(&mut self, high_byte_addr: u8) -> Result<u16, Error<I::Error>> {
        let high = self.read_virtual_register(high_byte_addr).await?;
        let low = self.read_virtual_register(high_byte_addr + 1).await?;

        Ok(((high as u16) << 8) | (low as u16))
    }

    /// Read f32 value from address
    #[maybe_async]
    async fn read_calibrated_channel(
        &mut self,
        high_byte_addr: u8,
    ) -> Result<f32, Error<I::Error>> {
        let b0 = self.read_virtual_register(high_byte_addr).await?;
        let b1 = self.read_virtual_register(high_byte_addr + 1).await?;
        let b2 = self.read_virtual_register(high_byte_addr + 2).await?;
        let b3 = self.read_virtual_register(high_byte_addr + 3).await?;

        let bits = u32::from_be_bytes([b0, b1, b2, b3]);
        Ok(f32::from_bits(bits))
    }

    /// Write to a virtual register
    #[maybe_async]
    async fn write_virtual_register(
        &mut self,
        virtual_addr: u8,
        data: u8,
    ) -> Result<(), Error<I::Error>> {
        const MAX_RETRIES: u8 = 100;

        for _ in 0..MAX_RETRIES {
            let mut status = [0u8; 1];
            self.device
                .write_read(AS7265X_ADDR, &[STATUS_REG], &mut status)
                .await?;
            if (status[0] & TX_VALID) == 0 {
                break;
            }
            self.delay.delay_ms(5).await;
        }

        self.device
            .write(AS7265X_ADDR, &[WRITE_REG, 0x80 | virtual_addr])
            .await?;

        for _ in 0..MAX_RETRIES {
            let mut status = [0u8; 1];
            self.device
                .write_read(AS7265X_ADDR, &[STATUS_REG], &mut status)
                .await?;
            if (status[0] & TX_VALID) == 0 {
                break;
            }
            self.delay.delay_ms(5).await;
        }

        self.device.write(AS7265X_ADDR, &[WRITE_REG, data]).await?;

        Ok(())
    }

    /// Read from a virtual register
    #[maybe_async]
    async fn read_virtual_register(&mut self, virtual_addr: u8) -> Result<u8, Error<I::Error>> {
        const MAX_RETRIES: u8 = 100;

        for _ in 0..MAX_RETRIES {
            let mut status = [0u8; 1];
            self.device
                .write_read(AS7265X_ADDR, &[STATUS_REG], &mut status)
                .await?;
            if (status[0] & TX_VALID) == 0 {
                break;
            }
            self.delay.delay_ms(5).await;
        }

        self.device
            .write(AS7265X_ADDR, &[WRITE_REG, virtual_addr])
            .await?;

        for _ in 0..MAX_RETRIES {
            let mut status = [0u8; 1];
            self.device
                .write_read(AS7265X_ADDR, &[STATUS_REG], &mut status)
                .await?;
            if (status[0] & RX_VALID) != 0 {
                break;
            }
            self.delay.delay_ms(5).await;
        }

        let mut data = [0u8; 1];
        self.device
            .write_read(AS7265X_ADDR, &[READ_REG], &mut data)
            .await?;

        Ok(data[0])
    }
}