Struct GovGAST1 

pub struct GovGAST1 {

    pub base: TurbineGovernorDynamics,
    pub a: Option<f64>,
    pub b: Option<f64>,
    pub db1: Option<f64>,
    pub db2: Option<f64>,
    pub eps: Option<f64>,
    pub fidle: Option<f64>,
    pub gv1: Option<f64>,
    pub gv2: Option<f64>,
    pub gv3: Option<f64>,
    pub gv4: Option<f64>,
    pub gv5: Option<f64>,
    pub gv6: Option<f64>,
    pub ka: Option<f64>,
    pub kt: Option<f64>,
    pub lmax: Option<f64>,
    pub loadinc: Option<f64>,
    pub ltrate: Option<f64>,
    pub mwbase: Option<f64>,
    pub pgv1: Option<f64>,
    pub pgv2: Option<f64>,
    pub pgv3: Option<f64>,
    pub pgv4: Option<f64>,
    pub pgv5: Option<f64>,
    pub pgv6: Option<f64>,
    pub r: Option<f64>,
    pub rmax: Option<f64>,
    pub t1: Option<f64>,
    pub t2: Option<f64>,
    pub t3: Option<f64>,
    pub t4: Option<f64>,
    pub t5: Option<f64>,
    pub tltr: Option<f64>,
    pub vmax: Option<f64>,
    pub vmin: Option<f64>,
}

Modified single shaft gas turbine.

Fields

base: TurbineGovernorDynamics

a: Option<f64>

Turbine power time constant numerator scale factor (a). Typical value = 0,8.

b: Option<f64>

Turbine power time constant denominator scale factor (b) (>0). Typical value = 1.

db1: Option<f64>

Intentional dead-band width (db1). Unit = Hz. Typical value = 0.

db2: Option<f64>

Unintentional dead-band (db2). Unit = MW. Typical value = 0.

eps: Option<f64>

Intentional db hysteresis (eps). Unit = Hz. Typical value = 0.

fidle: Option<f64>

Fuel flow at zero power output (Fidle). Typical value = 0,18.

gv1: Option<f64>

Nonlinear gain point 1, PU gv (Gv1). Typical value = 0.

gv2: Option<f64>

Nonlinear gain point 2,PU gv (Gv2). Typical value = 0.

gv3: Option<f64>

Nonlinear gain point 3, PU gv (Gv3). Typical value = 0.

gv4: Option<f64>

Nonlinear gain point 4, PU gv (Gv4). Typical value = 0.

gv5: Option<f64>

Nonlinear gain point 5, PU gv (Gv5). Typical value = 0.

gv6: Option<f64>

Nonlinear gain point 6, PU gv (Gv6). Typical value = 0.

ka: Option<f64>

Governor gain (Ka). Typical value = 0.

kt: Option<f64>

Temperature limiter gain (Kt). Typical value = 3.

lmax: Option<f64>

Ambient temperature load limit (Lmax). Lmax is the turbine power output corresponding to the limiting exhaust gas temperature. Typical value = 1.

loadinc: Option<f64>

Valve position change allowed at fast rate (Loadinc). Typical value = 0,05.

ltrate: Option<f64>

Maximum long term fuel valve opening rate (Ltrate). Typical value = 0,02.

mwbase: Option<f64>

Base for power values (MWbase) (> 0). Unit = MW.

pgv1: Option<f64>

Nonlinear gain point 1, PU power (Pgv1). Typical value = 0.

pgv2: Option<f64>

Nonlinear gain point 2, PU power (Pgv2). Typical value = 0.

pgv3: Option<f64>

Nonlinear gain point 3, PU power (Pgv3). Typical value = 0.

pgv4: Option<f64>

Nonlinear gain point 4, PU power (Pgv4). Typical value = 0.

pgv5: Option<f64>

Nonlinear gain point 5, PU power (Pgv5). Typical value = 0.

pgv6: Option<f64>

Nonlinear gain point 6, PU power (Pgv6). Typical value = 0.

r: Option<f64>

Permanent droop (R) (>0). Typical value = 0,04.

rmax: Option<f64>

Maximum fuel valve opening rate (Rmax). Unit = PU / s. Typical value = 1.

t1: Option<f64>

Governor mechanism time constant (T1) (>= 0). T1 represents the natural valve positioning time constant of the governor for small disturbances, as seen when rate limiting is not in effect. Typical value = 0,5.

t2: Option<f64>

Turbine power time constant (T2) (>= 0). T2 represents delay due to internal energy storage of the gas turbine engine. T2 can be used to give a rough approximation to the delay associated with acceleration of the compressor spool of a multi-shaft engine, or with the compressibility of gas in the plenum of the free power turbine of an aero-derivative unit, for example. Typical value = 0,5.

t3: Option<f64>

Turbine exhaust temperature time constant (T3) (>= 0). T3 represents delay in the exhaust temperature and load limiting system. Typical value = 3.

t4: Option<f64>

Governor lead time constant (T4) (>= 0). Typical value = 0.

t5: Option<f64>

Governor lag time constant (T5) (>= 0). If = 0, entire gain and lead-lag block is bypassed. Typical value = 0.

tltr: Option<f64>

Valve position averaging time constant (Tltr) (>= 0). Typical value = 10.

vmax: Option<f64>

Maximum turbine power, PU of MWbase (Vmax) (> GovGAST1.vmin). Typical value = 1.

vmin: Option<f64>

Minimum turbine power, PU of MWbase (Vmin) (< GovGAST1.vmax). Typical value = 0.

Implementations

impl GovGAST1

pub fn from_block(b: &RdfBlock) -> Self

Trait Implementations

impl CimElement for GovGAST1

fn mrid(&self) -> &str

fn type_name(&self) -> &'static str

fn as_any(&self) -> &dyn Any

fn to_json_value(&self) -> Value

fn to_block(&self) -> RdfBlock

impl Clone for GovGAST1

fn clone(&self) -> GovGAST1

Returns a duplicate of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for GovGAST1

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for GovGAST1

fn default() -> GovGAST1

Returns the “default value” for a type.

impl<'de> Deserialize<'de> for GovGAST1

fn deserialize<__D>(__deserializer: __D) -> Result<Self, __D::Error>

where __D: Deserializer<'de>,

Deserialize this value from the given Serde deserializer.

impl Serialize for GovGAST1

fn serialize<__S>(&self, __serializer: __S) -> Result<__S::Ok, __S::Error>

where __S: Serializer,

Serialize this value into the given Serde serializer.