Struct WindContPType3IEC 

pub struct WindContPType3IEC {

    pub base: IdentifiedObject,
    pub dpmax: Option<f64>,
    pub dprefmax: Option<f64>,
    pub dprefmin: Option<f64>,
    pub dthetamax: Option<f64>,
    pub dthetamaxuvrt: Option<f64>,
    pub kdtd: Option<f64>,
    pub kip: Option<f64>,
    pub kpp: Option<f64>,
    pub mpuvrt: Option<bool>,
    pub omegadtd: Option<f64>,
    pub omegaoffset: Option<f64>,
    pub pdtdmax: Option<f64>,
    pub tdvs: Option<f64>,
    pub thetaemin: Option<f64>,
    pub thetauscale: Option<f64>,
    pub tomegafiltp3: Option<f64>,
    pub tomegaref: Option<f64>,
    pub tpfiltp3: Option<f64>,
    pub tpord: Option<f64>,
    pub tufiltp3: Option<f64>,
    pub udvs: Option<f64>,
    pub updip: Option<f64>,
    pub zeta: Option<f64>,
}

P control model type 3. Reference: IEC 61400-27-1:2015, 5.6.5.4.

Fields

base: IdentifiedObject

dpmax: Option<f64>

Maximum wind turbine power ramp rate (dpmax). It is a type-dependent parameter.

dprefmax: Option<f64>

Maximum ramp rate of wind turbine reference power (dprefmax). It is a project-dependent parameter.

dprefmin: Option<f64>

Minimum ramp rate of wind turbine reference power (dprefmin). It is a project-dependent parameter.

dthetamax: Option<f64>

Ramp limitation of torque, required in some grid codes (dtmax). It is a project-dependent parameter.

dthetamaxuvrt: Option<f64>

Limitation of torque rise rate during UVRT (dthetamaxUVRT). It is a project-dependent parameter.

kdtd: Option<f64>

Gain for active drive train damping (KDTD). It is a type-dependent parameter.

kip: Option<f64>

PI controller integration parameter (KIp). It is a type-dependent parameter.

kpp: Option<f64>

PI controller proportional gain (KPp). It is a type-dependent parameter.

mpuvrt: Option<bool>

Enable UVRT power control mode (MpUVRT). It is a project-dependent parameter. true = voltage control (1 in the IEC model) false = reactive power control (0 in the IEC model).

omegadtd: Option<f64>

Active drive train damping frequency (omegaDTD). It can be calculated from two mass model parameters. It is a type-dependent parameter.

omegaoffset: Option<f64>

Offset to reference value that limits controller action during rotor speed changes (omegaoffset). It is a case-dependent parameter.

pdtdmax: Option<f64>

Maximum active drive train damping power (pDTDmax). It is a type-dependent parameter.

tdvs: Option<f64>

Time delay after deep voltage sags (TDVS) (>= 0). It is a project-dependent parameter.

thetaemin: Option<f64>

Minimum electrical generator torque (temin). It is a type-dependent parameter.

thetauscale: Option<f64>

Voltage scaling factor of reset-torque (tuscale). It is a project-dependent parameter.

tomegafiltp3: Option<f64>

Filter time constant for generator speed measurement (Tomegafiltp3) (>= 0). It is a type-dependent parameter.

tomegaref: Option<f64>

Time constant in speed reference filter (Tomega,ref) (>= 0). It is a type-dependent parameter.

tpfiltp3: Option<f64>

Filter time constant for power measurement (Tpfiltp3) (>= 0). It is a type-dependent parameter.

tpord: Option<f64>

Time constant in power order lag (Tpord). It is a type-dependent parameter.

tufiltp3: Option<f64>

Filter time constant for voltage measurement (Tufiltp3) (>= 0). It is a type-dependent parameter.

udvs: Option<f64>

Voltage limit for hold UVRT status after deep voltage sags (uDVS). It is a project-dependent parameter.

updip: Option<f64>

Voltage dip threshold for P-control (uPdip). Part of turbine control, often different (e.g 0.8) from converter thresholds. It is a project-dependent parameter.

zeta: Option<f64>

Coefficient for active drive train damping (zeta). It is a type-dependent parameter.

Implementations

impl WindContPType3IEC

pub fn from_block(b: &RdfBlock) -> Self

Trait Implementations

impl CimElement for WindContPType3IEC

fn mrid(&self) -> &str

fn type_name(&self) -> &'static str

fn as_any(&self) -> &dyn Any

fn to_json_value(&self) -> Value

fn to_block(&self) -> RdfBlock

impl Clone for WindContPType3IEC

fn clone(&self) -> WindContPType3IEC

Returns a duplicate of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for WindContPType3IEC

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for WindContPType3IEC

fn default() -> WindContPType3IEC

Returns the “default value” for a type.

impl<'de> Deserialize<'de> for WindContPType3IEC

fn deserialize<__D>(__deserializer: __D) -> Result<Self, __D::Error>

where __D: Deserializer<'de>,

Deserialize this value from the given Serde deserializer.

impl Serialize for WindContPType3IEC

fn serialize<__S>(&self, __serializer: __S) -> Result<__S::Ok, __S::Error>

where __S: Serializer,

Serialize this value into the given Serde serializer.