[−][src]Struct cc13x2_cc26x2_hal::crypto::irqstat::W
Value to write to the register
Methods
impl W
[src]
pub fn reset_value() -> W
[src]
Reset value of the register
pub unsafe fn bits(&mut self, bits: u32) -> &mut Self
[src]
Writes raw bits to the register
pub fn dma_bus_err(&mut self) -> _DMA_BUS_ERRW
[src]
Bit 31 - 31:31] This bit is set when a DMA bus error is detected during a DMA operation. The value of this register is held until it is cleared through the IRQCLR.DMA_BUS_ERR Note: This error is asserted if an error is detected on the AHB master interface during a DMA operation.
pub fn key_st_wr_err(&mut self) -> _KEY_ST_WR_ERRW
[src]
Bit 30 - 30:30] This bit is set when a write error is detected during the DMA write operation to the key store memory. The value of this register is held until it is cleared through the IRQCLR.KEY_ST_WR_ERR register. Note: This error is asserted if a DMA operation does not cover a full key area or more areas are written than expected.
pub fn key_st_rd_err(&mut self) -> _KEY_ST_RD_ERRW
[src]
Bit 29 - 29:29] This bit is set when a read error is detected during the read of a key from the key store, while copying it to the AES core. The value of this register is held until it is cleared through the IRQCLR.KEY_ST_RD_ERR register. Note: This error is asserted if a key location is selected in the key store that is not available.
pub fn reserved2(&mut self) -> _RESERVED2W
[src]
Bits 2:28 - 28:2] Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
pub fn dma_in_done(&mut self) -> _DMA_IN_DONEW
[src]
Bit 1 - 1:1] This read only bit returns the actual DMA data in done (irq_data_in_done) interrupt status of the DMA data in done interrupt output pin (irq_data_in_done).
pub fn result_avail(&mut self) -> _RESULT_AVAILW
[src]
Bit 0 - 0:0] This read only bit returns the actual result available (irq_result_av) interrupt status of the result available interrupt output pin (irq_result_av).
Auto Trait Implementations
Blanket Implementations
impl<T> From for T
[src]
impl<T, U> TryFrom for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> TryInto for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
impl<T, U> Into for T where
U: From<T>,
[src]
U: From<T>,
impl<T> Borrow for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut for T where
T: ?Sized,
[src]
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<T> Same for T
type Output = T
Should always be Self