Struct UpdateResolverEndpointInput

#[non_exhaustive]
pub struct UpdateResolverEndpointInput {
    pub resolver_endpoint_id: Option<String>,
    pub name: Option<String>,
    pub resolver_endpoint_type: Option<ResolverEndpointType>,
    pub update_ip_addresses: Option<Vec<UpdateIpAddress>>,
    pub protocols: Option<Vec<Protocol>>,
}

Fields (Non-exhaustive)

Non-exhaustive structs could have additional fields added in future. Therefore, non-exhaustive structs cannot be constructed in external crates using the traditional Struct { .. } syntax; cannot be matched against without a wildcard ..; and struct update syntax will not work.

resolver_endpoint_id: Option<String>

The ID of the Resolver endpoint that you want to update.

name: Option<String>

The name of the Resolver endpoint that you want to update.

resolver_endpoint_type: Option<ResolverEndpointType>

Specifies the endpoint type for what type of IP address the endpoint uses to forward DNS queries.

Updating to IPV6 type isn't currently supported.

update_ip_addresses: Option<Vec<UpdateIpAddress>>

Specifies the IPv6 address when you update the Resolver endpoint from IPv4 to dual-stack. If you don't specify an IPv6 address, one will be automatically chosen from your subnet.

protocols: Option<Vec<Protocol>>

The protocols you want to use for the endpoint. DoH-FIPS is applicable for default inbound endpoints only.

For a default inbound endpoint you can apply the protocols as follows:

• Do53 and DoH in combination.

• Do53 and DoH-FIPS in combination.

• Do53 alone.

• DoH alone.

• DoH-FIPS alone.

• None, which is treated as Do53.

For a delegation inbound endpoint you can use Do53 only.

For an outbound endpoint you can apply the protocols as follows:

• Do53 and DoH in combination.

• Do53 alone.

• DoH alone.

• None, which is treated as Do53.

You can't change the protocol of an inbound endpoint directly from only Do53 to only DoH, or DoH-FIPS. This is to prevent a sudden disruption to incoming traffic that relies on Do53. To change the protocol from Do53 to DoH, or DoH-FIPS, you must first enable both Do53 and DoH, or Do53 and DoH-FIPS, to make sure that all incoming traffic has transferred to using the DoH protocol, or DoH-FIPS, and then remove the Do53.

Implementations

impl UpdateResolverEndpointInput

pub fn resolver_endpoint_id(&self) -> Option<&str>

The ID of the Resolver endpoint that you want to update.

pub fn name(&self) -> Option<&str>

The name of the Resolver endpoint that you want to update.

pub fn resolver_endpoint_type(&self) -> Option<&ResolverEndpointType>

Specifies the endpoint type for what type of IP address the endpoint uses to forward DNS queries.

Updating to IPV6 type isn't currently supported.

pub fn update_ip_addresses(&self) -> &[UpdateIpAddress]

Specifies the IPv6 address when you update the Resolver endpoint from IPv4 to dual-stack. If you don't specify an IPv6 address, one will be automatically chosen from your subnet.

If no value was sent for this field, a default will be set. If you want to determine if no value was sent, use .update_ip_addresses.is_none().

pub fn protocols(&self) -> &[Protocol]

The protocols you want to use for the endpoint. DoH-FIPS is applicable for default inbound endpoints only.

For a default inbound endpoint you can apply the protocols as follows:

• Do53 and DoH in combination.

• Do53 and DoH-FIPS in combination.

• Do53 alone.

• DoH alone.

• DoH-FIPS alone.

• None, which is treated as Do53.

For a delegation inbound endpoint you can use Do53 only.

For an outbound endpoint you can apply the protocols as follows:

• Do53 and DoH in combination.

• Do53 alone.

• DoH alone.

• None, which is treated as Do53.

You can't change the protocol of an inbound endpoint directly from only Do53 to only DoH, or DoH-FIPS. This is to prevent a sudden disruption to incoming traffic that relies on Do53. To change the protocol from Do53 to DoH, or DoH-FIPS, you must first enable both Do53 and DoH, or Do53 and DoH-FIPS, to make sure that all incoming traffic has transferred to using the DoH protocol, or DoH-FIPS, and then remove the Do53.

If no value was sent for this field, a default will be set. If you want to determine if no value was sent, use .protocols.is_none().

impl UpdateResolverEndpointInput

pub fn builder() -> UpdateResolverEndpointInputBuilder

Creates a new builder-style object to manufacture UpdateResolverEndpointInput.

Trait Implementations

impl Clone for UpdateResolverEndpointInput

fn clone(&self) -> UpdateResolverEndpointInput

Returns a duplicate of the value.

const fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for UpdateResolverEndpointInput

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl PartialEq for UpdateResolverEndpointInput

fn eq(&self, other: &UpdateResolverEndpointInput) -> bool

Tests for self and other values to be equal, and is used by ==.

const fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl StructuralPartialEq for UpdateResolverEndpointInput