Struct UpdateResolverEndpointInput 

#[non_exhaustive]
pub struct UpdateResolverEndpointInput {
    pub resolver_endpoint_id: Option<String>,
    pub name: Option<String>,
    pub resolver_endpoint_type: Option<ResolverEndpointType>,
    pub update_ip_addresses: Option<Vec<UpdateIpAddress>>,
    pub protocols: Option<Vec<Protocol>>,
    pub rni_enhanced_metrics_enabled: Option<bool>,
    pub target_name_server_metrics_enabled: Option<bool>,
}

Fields (Non-exhaustive)

Non-exhaustive structs could have additional fields added in future. Therefore, non-exhaustive structs cannot be constructed in external crates using the traditional Struct { .. } syntax; cannot be matched against without a wildcard ..; and struct update syntax will not work.

resolver_endpoint_id: Option<String>

The ID of the Resolver endpoint that you want to update.

name: Option<String>

The name of the Resolver endpoint that you want to update.

resolver_endpoint_type: Option<ResolverEndpointType>

Specifies the endpoint type for what type of IP address the endpoint uses to forward DNS queries.

Updating to IPV6 type isn't currently supported.

update_ip_addresses: Option<Vec<UpdateIpAddress>>

Specifies the IPv6 address when you update the Resolver endpoint from IPv4 to dual-stack. If you don't specify an IPv6 address, one will be automatically chosen from your subnet.

protocols: Option<Vec<Protocol>>

The protocols you want to use for the endpoint. DoH-FIPS is applicable for default inbound endpoints only.

For a default inbound endpoint you can apply the protocols as follows:

• Do53 and DoH in combination.

• Do53 and DoH-FIPS in combination.

• Do53 alone.

• DoH alone.

• DoH-FIPS alone.

• None, which is treated as Do53.

For a delegation inbound endpoint you can use Do53 only.

For an outbound endpoint you can apply the protocols as follows:

• Do53 and DoH in combination.

• Do53 alone.

• DoH alone.

• None, which is treated as Do53.

You can't change the protocol of an inbound endpoint directly from only Do53 to only DoH, or DoH-FIPS. This is to prevent a sudden disruption to incoming traffic that relies on Do53. To change the protocol from Do53 to DoH, or DoH-FIPS, you must first enable both Do53 and DoH, or Do53 and DoH-FIPS, to make sure that all incoming traffic has transferred to using the DoH protocol, or DoH-FIPS, and then remove the Do53.

rni_enhanced_metrics_enabled: Option<bool>

Updates whether RNI enhanced metrics are enabled for the Resolver endpoints. When set to true, one-minute granular metrics are published in CloudWatch for each RNI associated with this endpoint. When set to false, metrics are not published.

Standard CloudWatch pricing and charges are applied for using the Route 53 Resolver endpoint RNI enhanced metrics. For more information, see Detailed metrics.

target_name_server_metrics_enabled: Option<bool>

Updates whether target name server metrics are enabled for the outbound Resolver endpoints. When set to true, one-minute granular metrics are published in CloudWatch for each target name server associated with this endpoint. When set to false, metrics are not published. This setting is not supported for inbound Resolver endpoints.

Standard CloudWatch pricing and charges are applied for using the Route 53 Resolver endpoint target name server metrics. For more information, see Detailed metrics.

Implementations

impl UpdateResolverEndpointInput

pub fn resolver_endpoint_id(&self) -> Option<&str>

The ID of the Resolver endpoint that you want to update.

pub fn name(&self) -> Option<&str>

The name of the Resolver endpoint that you want to update.

pub fn resolver_endpoint_type(&self) -> Option<&ResolverEndpointType>

Specifies the endpoint type for what type of IP address the endpoint uses to forward DNS queries.

Updating to IPV6 type isn't currently supported.

pub fn update_ip_addresses(&self) -> &[UpdateIpAddress]

Specifies the IPv6 address when you update the Resolver endpoint from IPv4 to dual-stack. If you don't specify an IPv6 address, one will be automatically chosen from your subnet.

If no value was sent for this field, a default will be set. If you want to determine if no value was sent, use .update_ip_addresses.is_none().

pub fn protocols(&self) -> &[Protocol]

The protocols you want to use for the endpoint. DoH-FIPS is applicable for default inbound endpoints only.

For a default inbound endpoint you can apply the protocols as follows:

• Do53 and DoH in combination.

• Do53 and DoH-FIPS in combination.

• Do53 alone.

• DoH alone.

• DoH-FIPS alone.

• None, which is treated as Do53.

For a delegation inbound endpoint you can use Do53 only.

For an outbound endpoint you can apply the protocols as follows:

• Do53 and DoH in combination.

• Do53 alone.

• DoH alone.

• None, which is treated as Do53.

You can't change the protocol of an inbound endpoint directly from only Do53 to only DoH, or DoH-FIPS. This is to prevent a sudden disruption to incoming traffic that relies on Do53. To change the protocol from Do53 to DoH, or DoH-FIPS, you must first enable both Do53 and DoH, or Do53 and DoH-FIPS, to make sure that all incoming traffic has transferred to using the DoH protocol, or DoH-FIPS, and then remove the Do53.

If no value was sent for this field, a default will be set. If you want to determine if no value was sent, use .protocols.is_none().

pub fn rni_enhanced_metrics_enabled(&self) -> Option<bool>

Updates whether RNI enhanced metrics are enabled for the Resolver endpoints. When set to true, one-minute granular metrics are published in CloudWatch for each RNI associated with this endpoint. When set to false, metrics are not published.

Standard CloudWatch pricing and charges are applied for using the Route 53 Resolver endpoint RNI enhanced metrics. For more information, see Detailed metrics.

pub fn target_name_server_metrics_enabled(&self) -> Option<bool>

Updates whether target name server metrics are enabled for the outbound Resolver endpoints. When set to true, one-minute granular metrics are published in CloudWatch for each target name server associated with this endpoint. When set to false, metrics are not published. This setting is not supported for inbound Resolver endpoints.

Standard CloudWatch pricing and charges are applied for using the Route 53 Resolver endpoint target name server metrics. For more information, see Detailed metrics.

impl UpdateResolverEndpointInput

pub fn builder() -> UpdateResolverEndpointInputBuilder

Creates a new builder-style object to manufacture UpdateResolverEndpointInput.

Trait Implementations

impl Clone for UpdateResolverEndpointInput

fn clone(&self) -> UpdateResolverEndpointInput

Returns a duplicate of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for UpdateResolverEndpointInput

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl PartialEq for UpdateResolverEndpointInput

fn eq(&self, other: &UpdateResolverEndpointInput) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl StructuralPartialEq for UpdateResolverEndpointInput