Struct aws_sdk_ec2::client::fluent_builders::CreateRoute

pub struct CreateRoute { /* private fields */ }

Fluent builder constructing a request to CreateRoute.

Creates a route in a route table within a VPC.

You must specify either a destination CIDR block or a prefix list ID. You must also specify exactly one of the resources from the parameter list.

When determining how to route traffic, we use the route with the most specific match. For example, traffic is destined for the IPv4 address 192.0.2.3, and the route table includes the following two IPv4 routes:

• 192.0.2.0/24 (goes to some target A)

• 192.0.2.0/28 (goes to some target B)

Both routes apply to the traffic destined for 192.0.2.3. However, the second route in the list covers a smaller number of IP addresses and is therefore more specific, so we use that route to determine where to target the traffic.

For more information about route tables, see Route tables in the Amazon Virtual Private Cloud User Guide.

Implementations

impl CreateRoute

pub async fn customize(
    self
) -> Result<CustomizableOperation<CreateRoute, AwsResponseRetryClassifier>, SdkError<CreateRouteError>>

Consume this builder, creating a customizable operation that can be modified before being sent. The operation’s inner http::Request can be modified as well.

pub async fn send(self) -> Result<CreateRouteOutput, SdkError<CreateRouteError>>

Sends the request and returns the response.

If an error occurs, an SdkError will be returned with additional details that can be matched against.

By default, any retryable failures will be retried twice. Retry behavior is configurable with the RetryConfig, which can be set when configuring the client.

pub fn destination_cidr_block(self, input: impl Into<String>) -> Self

The IPv4 CIDR address block used for the destination match. Routing decisions are based on the most specific match. We modify the specified CIDR block to its canonical form; for example, if you specify 100.68.0.18/18, we modify it to 100.68.0.0/18.

pub fn set_destination_cidr_block(self, input: Option<String>) -> Self

The IPv4 CIDR address block used for the destination match. Routing decisions are based on the most specific match. We modify the specified CIDR block to its canonical form; for example, if you specify 100.68.0.18/18, we modify it to 100.68.0.0/18.

pub fn destination_ipv6_cidr_block(self, input: impl Into<String>) -> Self

The IPv6 CIDR block used for the destination match. Routing decisions are based on the most specific match.

pub fn set_destination_ipv6_cidr_block(self, input: Option<String>) -> Self

The IPv6 CIDR block used for the destination match. Routing decisions are based on the most specific match.

pub fn destination_prefix_list_id(self, input: impl Into<String>) -> Self

The ID of a prefix list used for the destination match.

pub fn set_destination_prefix_list_id(self, input: Option<String>) -> Self

The ID of a prefix list used for the destination match.

pub fn dry_run(self, input: bool) -> Self

Checks whether you have the required permissions for the action, without actually making the request, and provides an error response. If you have the required permissions, the error response is DryRunOperation. Otherwise, it is UnauthorizedOperation.

pub fn set_dry_run(self, input: Option<bool>) -> Self

Checks whether you have the required permissions for the action, without actually making the request, and provides an error response. If you have the required permissions, the error response is DryRunOperation. Otherwise, it is UnauthorizedOperation.

pub fn vpc_endpoint_id(self, input: impl Into<String>) -> Self

The ID of a VPC endpoint. Supported for Gateway Load Balancer endpoints only.

pub fn set_vpc_endpoint_id(self, input: Option<String>) -> Self

The ID of a VPC endpoint. Supported for Gateway Load Balancer endpoints only.

pub fn egress_only_internet_gateway_id(self, input: impl Into<String>) -> Self

[IPv6 traffic only] The ID of an egress-only internet gateway.

pub fn set_egress_only_internet_gateway_id(self, input: Option<String>) -> Self

[IPv6 traffic only] The ID of an egress-only internet gateway.

pub fn gateway_id(self, input: impl Into<String>) -> Self

The ID of an internet gateway or virtual private gateway attached to your VPC.

pub fn set_gateway_id(self, input: Option<String>) -> Self

The ID of an internet gateway or virtual private gateway attached to your VPC.

pub fn instance_id(self, input: impl Into<String>) -> Self

The ID of a NAT instance in your VPC. The operation fails if you specify an instance ID unless exactly one network interface is attached.

pub fn set_instance_id(self, input: Option<String>) -> Self

The ID of a NAT instance in your VPC. The operation fails if you specify an instance ID unless exactly one network interface is attached.

pub fn nat_gateway_id(self, input: impl Into<String>) -> Self

[IPv4 traffic only] The ID of a NAT gateway.

pub fn set_nat_gateway_id(self, input: Option<String>) -> Self

[IPv4 traffic only] The ID of a NAT gateway.

pub fn transit_gateway_id(self, input: impl Into<String>) -> Self

The ID of a transit gateway.

pub fn set_transit_gateway_id(self, input: Option<String>) -> Self

The ID of a transit gateway.

pub fn local_gateway_id(self, input: impl Into<String>) -> Self

The ID of the local gateway.

pub fn set_local_gateway_id(self, input: Option<String>) -> Self

The ID of the local gateway.

pub fn carrier_gateway_id(self, input: impl Into<String>) -> Self

The ID of the carrier gateway.

You can only use this option when the VPC contains a subnet which is associated with a Wavelength Zone.

pub fn set_carrier_gateway_id(self, input: Option<String>) -> Self

The ID of the carrier gateway.

You can only use this option when the VPC contains a subnet which is associated with a Wavelength Zone.

pub fn network_interface_id(self, input: impl Into<String>) -> Self

The ID of a network interface.

pub fn set_network_interface_id(self, input: Option<String>) -> Self

The ID of a network interface.

pub fn route_table_id(self, input: impl Into<String>) -> Self

The ID of the route table for the route.

pub fn set_route_table_id(self, input: Option<String>) -> Self

The ID of the route table for the route.

pub fn vpc_peering_connection_id(self, input: impl Into<String>) -> Self

The ID of a VPC peering connection.

pub fn set_vpc_peering_connection_id(self, input: Option<String>) -> Self

The ID of a VPC peering connection.

pub fn core_network_arn(self, input: impl Into<String>) -> Self

The Amazon Resource Name (ARN) of the core network.

pub fn set_core_network_arn(self, input: Option<String>) -> Self

The Amazon Resource Name (ARN) of the core network.

Trait Implementations

impl Clone for CreateRoute

fn clone(&self) -> CreateRoute

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for CreateRoute

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.