Struct aws_sdk_ec2::model::nat_gateway::Builder

#[non_exhaustive]
pub struct Builder { /* fields omitted */ }

A builder for NatGateway

Implementations

impl Builder

pub fn create_time(self, input: Instant) -> Self

The date and time the NAT gateway was created.

pub fn set_create_time(self, input: Option<Instant>) -> Self

The date and time the NAT gateway was created.

pub fn delete_time(self, input: Instant) -> Self

The date and time the NAT gateway was deleted, if applicable.

pub fn set_delete_time(self, input: Option<Instant>) -> Self

The date and time the NAT gateway was deleted, if applicable.

pub fn failure_code(self, input: impl Into<String>) -> Self

If the NAT gateway could not be created, specifies the error code for the failure. (InsufficientFreeAddressesInSubnet | Gateway.NotAttached | InvalidAllocationID.NotFound | Resource.AlreadyAssociated | InternalError | InvalidSubnetID.NotFound)

pub fn set_failure_code(self, input: Option<String>) -> Self

If the NAT gateway could not be created, specifies the error code for the failure. (InsufficientFreeAddressesInSubnet | Gateway.NotAttached | InvalidAllocationID.NotFound | Resource.AlreadyAssociated | InternalError | InvalidSubnetID.NotFound)

pub fn failure_message(self, input: impl Into<String>) -> Self

If the NAT gateway could not be created, specifies the error message for the failure, that corresponds to the error code.

• For InsufficientFreeAddressesInSubnet: "Subnet has insufficient free addresses to create this NAT gateway"

• For Gateway.NotAttached: "Network vpc-xxxxxxxx has no Internet gateway attached"

• For InvalidAllocationID.NotFound: "Elastic IP address eipalloc-xxxxxxxx could not be associated with this NAT gateway"

• For Resource.AlreadyAssociated: "Elastic IP address eipalloc-xxxxxxxx is already associated"

• For InternalError: "Network interface eni-xxxxxxxx, created and used internally by this NAT gateway is in an invalid state. Please try again."

• For InvalidSubnetID.NotFound: "The specified subnet subnet-xxxxxxxx does not exist or could not be found."

pub fn set_failure_message(self, input: Option<String>) -> Self

If the NAT gateway could not be created, specifies the error message for the failure, that corresponds to the error code.

• For InsufficientFreeAddressesInSubnet: "Subnet has insufficient free addresses to create this NAT gateway"

• For Gateway.NotAttached: "Network vpc-xxxxxxxx has no Internet gateway attached"

• For InvalidAllocationID.NotFound: "Elastic IP address eipalloc-xxxxxxxx could not be associated with this NAT gateway"

• For Resource.AlreadyAssociated: "Elastic IP address eipalloc-xxxxxxxx is already associated"

• For InternalError: "Network interface eni-xxxxxxxx, created and used internally by this NAT gateway is in an invalid state. Please try again."

• For InvalidSubnetID.NotFound: "The specified subnet subnet-xxxxxxxx does not exist or could not be found."

pub fn nat_gateway_addresses(self, input: impl Into<NatGatewayAddress>) -> Self

Appends an item to nat_gateway_addresses.

To override the contents of this collection use set_nat_gateway_addresses.

Information about the IP addresses and network interface associated with the NAT gateway.

pub fn set_nat_gateway_addresses(
    self,
    input: Option<Vec<NatGatewayAddress>>
) -> Self

Information about the IP addresses and network interface associated with the NAT gateway.

pub fn nat_gateway_id(self, input: impl Into<String>) -> Self

The ID of the NAT gateway.

pub fn set_nat_gateway_id(self, input: Option<String>) -> Self

The ID of the NAT gateway.

pub fn provisioned_bandwidth(self, input: ProvisionedBandwidth) -> Self

Reserved. If you need to sustain traffic greater than the documented limits, contact us through the Support Center.

pub fn set_provisioned_bandwidth(
    self,
    input: Option<ProvisionedBandwidth>
) -> Self

Reserved. If you need to sustain traffic greater than the documented limits, contact us through the Support Center.

pub fn state(self, input: NatGatewayState) -> Self

The state of the NAT gateway.

• pending: The NAT gateway is being created and is not ready to process traffic.

• failed: The NAT gateway could not be created. Check the failureCode and failureMessage fields for the reason.

• available: The NAT gateway is able to process traffic. This status remains until you delete the NAT gateway, and does not indicate the health of the NAT gateway.

• deleting: The NAT gateway is in the process of being terminated and may still be processing traffic.

• deleted: The NAT gateway has been terminated and is no longer processing traffic.

pub fn set_state(self, input: Option<NatGatewayState>) -> Self

The state of the NAT gateway.

• pending: The NAT gateway is being created and is not ready to process traffic.

• failed: The NAT gateway could not be created. Check the failureCode and failureMessage fields for the reason.

• available: The NAT gateway is able to process traffic. This status remains until you delete the NAT gateway, and does not indicate the health of the NAT gateway.

• deleting: The NAT gateway is in the process of being terminated and may still be processing traffic.

• deleted: The NAT gateway has been terminated and is no longer processing traffic.

pub fn subnet_id(self, input: impl Into<String>) -> Self

The ID of the subnet in which the NAT gateway is located.

pub fn set_subnet_id(self, input: Option<String>) -> Self

The ID of the subnet in which the NAT gateway is located.

pub fn vpc_id(self, input: impl Into<String>) -> Self

The ID of the VPC in which the NAT gateway is located.

pub fn set_vpc_id(self, input: Option<String>) -> Self

The ID of the VPC in which the NAT gateway is located.

pub fn tags(self, input: impl Into<Tag>) -> Self

Appends an item to tags.

To override the contents of this collection use set_tags.

The tags for the NAT gateway.

pub fn set_tags(self, input: Option<Vec<Tag>>) -> Self

The tags for the NAT gateway.

pub fn connectivity_type(self, input: ConnectivityType) -> Self

Indicates whether the NAT gateway supports public or private connectivity.

pub fn set_connectivity_type(self, input: Option<ConnectivityType>) -> Self

Indicates whether the NAT gateway supports public or private connectivity.

pub fn build(self) -> NatGateway

Consumes the builder and constructs a NatGateway

Trait Implementations

impl Clone for Builder

fn clone(&self) -> Builder

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for Builder

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for Builder

fn default() -> Builder

Returns the “default value” for a type.

impl PartialEq<Builder> for Builder

fn eq(&self, other: &Builder) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Builder) -> bool

This method tests for !=.

impl StructuralPartialEq for Builder