Struct aws_sdk_directconnect::output::UpdateConnectionOutput

#[non_exhaustive]
pub struct UpdateConnectionOutput { /* private fields */ }

Information about an Direct Connect connection.

Implementations

impl UpdateConnectionOutput

pub fn owner_account(&self) -> Option<&str>

The ID of the Amazon Web Services account that owns the connection.

pub fn connection_id(&self) -> Option<&str>

The ID of the connection.

pub fn connection_name(&self) -> Option<&str>

The name of the connection.

pub fn connection_state(&self) -> Option<&ConnectionState>

The state of the connection. The following are the possible values:

• ordering: The initial state of a hosted connection provisioned on an interconnect. The connection stays in the ordering state until the owner of the hosted connection confirms or declines the connection order.

• requested: The initial state of a standard connection. The connection stays in the requested state until the Letter of Authorization (LOA) is sent to the customer.

• pending: The connection has been approved and is being initialized.

• available: The network link is up and the connection is ready for use.

• down: The network link is down.

• deleting: The connection is being deleted.

• deleted: The connection has been deleted.

• rejected: A hosted connection in the ordering state enters the rejected state if it is deleted by the customer.

• unknown: The state of the connection is not available.

pub fn region(&self) -> Option<&str>

The Amazon Web Services Region where the connection is located.

pub fn location(&self) -> Option<&str>

The location of the connection.

pub fn bandwidth(&self) -> Option<&str>

The bandwidth of the connection.

pub fn vlan(&self) -> i32

The ID of the VLAN.

pub fn partner_name(&self) -> Option<&str>

The name of the Direct Connect service provider associated with the connection.

pub fn loa_issue_time(&self) -> Option<&DateTime>

The time of the most recent call to DescribeLoa for this connection.

pub fn lag_id(&self) -> Option<&str>

The ID of the LAG.

pub fn aws_device(&self) -> Option<&str>

The Direct Connect endpoint on which the physical connection terminates.

pub fn jumbo_frame_capable(&self) -> Option<bool>

Indicates whether jumbo frames (9001 MTU) are supported.

pub fn aws_device_v2(&self) -> Option<&str>

The Direct Connect endpoint that terminates the physical connection.

pub fn aws_logical_device_id(&self) -> Option<&str>

The Direct Connect endpoint that terminates the logical connection. This device might be different than the device that terminates the physical connection.

pub fn has_logical_redundancy(&self) -> Option<&HasLogicalRedundancy>

Indicates whether the connection supports a secondary BGP peer in the same address family (IPv4/IPv6).

pub fn tags(&self) -> Option<&[Tag]>

The tags associated with the connection.

pub fn provider_name(&self) -> Option<&str>

The name of the service provider associated with the connection.

pub fn mac_sec_capable(&self) -> Option<bool>

Indicates whether the connection supports MAC Security (MACsec).

pub fn port_encryption_status(&self) -> Option<&str>

The MAC Security (MACsec) port link status of the connection.

The valid values are Encryption Up, which means that there is an active Connection Key Name, or Encryption Down.

pub fn encryption_mode(&self) -> Option<&str>

The MAC Security (MACsec) connection encryption mode.

The valid values are no_encrypt, should_encrypt, and must_encrypt.

pub fn mac_sec_keys(&self) -> Option<&[MacSecKey]>

The MAC Security (MACsec) security keys associated with the connection.

impl UpdateConnectionOutput

pub fn builder() -> Builder

Creates a new builder-style object to manufacture UpdateConnectionOutput.

Trait Implementations

impl Clone for UpdateConnectionOutput

fn clone(&self) -> UpdateConnectionOutput

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for UpdateConnectionOutput

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl PartialEq<UpdateConnectionOutput> for UpdateConnectionOutput

fn eq(&self, other: &UpdateConnectionOutput) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl StructuralPartialEq for UpdateConnectionOutput