Enum stm32wl::stm32wl5x_cm4::tim1::cr2::MMS2_A

#[repr(u8)]
pub enum MMS2_A {
    Reset,
    Enable,
    Update,
    ComparePulse,
    CompareOc1,
    CompareOc2,
    CompareOc3,
    CompareOc4,
    CompareOc5,
    CompareOc6,
    PulseOc4,
    PulseOc6,
    RisingOc46,
    RisingOc4FallingOc6,
    RisingOc56,
    RisingOc5FallingOc6,
}

Master mode selection 2

Value on reset: 0

Variants

Reset

0: Reset - the UG bit from the TIMx_EGR register is used as trigger output (TRGO2). If the reset is generated by the trigger input (slave mode controller configured in reset mode), the signal on TRGO2 is delayed compared to the actual reset

Enable

1: Enable - the Counter Enable signal CNT_EN is used as trigger output (TRGO2). It is useful to start several timers at the same time or to control a window in which a slave timer is enabled. The Counter Enable signal is generated by a logic AND between the CEN control bit and the trigger input when configured in Gated mode. When the Counter Enable signal is controlled by the trigger input, there is a delay on TRGO2, except if the Master/Slave mode is selected (see the MSM bit description in TIMx_SMCR register)

Update

2: Update - the update event is selected as trigger output (TRGO2). For instance, a master timer can then be used as a prescaler for a slave timer

ComparePulse

3: Compare pulse - the trigger output sends a positive pulse when the CC1IF flag is to be set (even if it was already high), as soon as a capture or compare match occurs (TRGO2)

CompareOc1

4: Compare - OC1REFC signal is used as trigger output (TRGO2)

CompareOc2

5: Compare - OC2REFC signal is used as trigger output (TRGO2)

CompareOc3

6: Compare - OC3REFC signal is used as trigger output (TRGO2)

CompareOc4

7: Compare - OC4REFC signal is used as trigger output (TRGO2)

CompareOc5

8: Compare - OC5REFC signal is used as trigger output (TRGO2)

CompareOc6

9: Compare - OC6REFC signal is used as trigger output (TRGO2)

PulseOc4

10: Compare Pulse - OC4REFC rising or falling edges generate pulses on TRGO2

PulseOc6

11: Compare Pulse - OC6REFC rising or falling edges generate pulses on TRGO2

RisingOc46

12: Compare Pulse - OC4REFC or OC6REFC rising edges generate pulses on TRGO2

RisingOc4FallingOc6

13: Compare Pulse - OC4REFC rising or OC6REFC falling edges generate pulses on TRGO2

RisingOc56

14: Compare Pulse - OC5REFC or OC6REFC rising edges generate pulses on TRGO2

RisingOc5FallingOc6

15: Compare Pulse - OC5REFC rising or OC6REFC falling edges generate pulses on TRGO2

Trait Implementations

impl Clone for MMS2_A

fn clone(&self) -> MMS2_A

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for MMS2_A

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl From<MMS2_A> for u8

fn from(variant: MMS2_A) -> Self

Converts to this type from the input type.

impl PartialEq<MMS2_A> for MMS2_A

fn eq(&self, other: &MMS2_A) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=.

impl Copy for MMS2_A

impl StructuralPartialEq for MMS2_A