Struct stm32h7::stm32h743v::pwr::wkupepr::R

pub struct R { /* fields omitted */ }

Value read from the register

Methods

impl R

pub fn bits(&self) -> u32

Value of the register as raw bits

pub fn wkupen1(&self) -> WKUPEN1R

Bit 0 - Enable Wakeup Pin WKUPn+1 Each bit is set and cleared by software. Note: An additional wakeup event is detected if WKUPn+1 pin is enabled (by setting the WKUPENn+1 bit) when WKUPn+1 pin level is already high when WKUPPn+1 selects rising edge, or low when WKUPPn+1 selects falling edge.

pub fn wkupen2(&self) -> WKUPEN2R

Bit 1 - Enable Wakeup Pin WKUPn+1 Each bit is set and cleared by software. Note: An additional wakeup event is detected if WKUPn+1 pin is enabled (by setting the WKUPENn+1 bit) when WKUPn+1 pin level is already high when WKUPPn+1 selects rising edge, or low when WKUPPn+1 selects falling edge.

pub fn wkupen3(&self) -> WKUPEN3R

Bit 2 - Enable Wakeup Pin WKUPn+1 Each bit is set and cleared by software. Note: An additional wakeup event is detected if WKUPn+1 pin is enabled (by setting the WKUPENn+1 bit) when WKUPn+1 pin level is already high when WKUPPn+1 selects rising edge, or low when WKUPPn+1 selects falling edge.

pub fn wkupen4(&self) -> WKUPEN4R

Bit 3 - Enable Wakeup Pin WKUPn+1 Each bit is set and cleared by software. Note: An additional wakeup event is detected if WKUPn+1 pin is enabled (by setting the WKUPENn+1 bit) when WKUPn+1 pin level is already high when WKUPPn+1 selects rising edge, or low when WKUPPn+1 selects falling edge.

pub fn wkupen5(&self) -> WKUPEN5R

Bit 4 - Enable Wakeup Pin WKUPn+1 Each bit is set and cleared by software. Note: An additional wakeup event is detected if WKUPn+1 pin is enabled (by setting the WKUPENn+1 bit) when WKUPn+1 pin level is already high when WKUPPn+1 selects rising edge, or low when WKUPPn+1 selects falling edge.

pub fn wkupen6(&self) -> WKUPEN6R

Bit 5 - Enable Wakeup Pin WKUPn+1 Each bit is set and cleared by software. Note: An additional wakeup event is detected if WKUPn+1 pin is enabled (by setting the WKUPENn+1 bit) when WKUPn+1 pin level is already high when WKUPPn+1 selects rising edge, or low when WKUPPn+1 selects falling edge.

pub fn wkupp1(&self) -> WKUPP1R

Bit 8 - Wakeup pin polarity bit for WKUPn-7 These bits define the polarity used for event detection on WKUPn-7 external wakeup pin.

pub fn wkupp2(&self) -> WKUPP2R

Bit 9 - Wakeup pin polarity bit for WKUPn-7 These bits define the polarity used for event detection on WKUPn-7 external wakeup pin.

pub fn wkupp3(&self) -> WKUPP3R

Bit 10 - Wakeup pin polarity bit for WKUPn-7 These bits define the polarity used for event detection on WKUPn-7 external wakeup pin.

pub fn wkupp4(&self) -> WKUPP4R

Bit 11 - Wakeup pin polarity bit for WKUPn-7 These bits define the polarity used for event detection on WKUPn-7 external wakeup pin.

pub fn wkupp5(&self) -> WKUPP5R

Bit 12 - Wakeup pin polarity bit for WKUPn-7 These bits define the polarity used for event detection on WKUPn-7 external wakeup pin.

pub fn wkupp6(&self) -> WKUPP6R

Bit 13 - Wakeup pin polarity bit for WKUPn-7 These bits define the polarity used for event detection on WKUPn-7 external wakeup pin.

pub fn wkuppupd1(&self) -> WKUPPUPD1R

Bits 16:17 - Wakeup pin pull configuration

pub fn wkuppupd2(&self) -> WKUPPUPD2R

Bits 18:19 - Wakeup pin pull configuration

pub fn wkuppupd3(&self) -> WKUPPUPD3R

Bits 20:21 - Wakeup pin pull configuration

pub fn wkuppupd4(&self) -> WKUPPUPD4R

Bits 22:23 - Wakeup pin pull configuration

pub fn wkuppupd5(&self) -> WKUPPUPD5R

Bits 24:25 - Wakeup pin pull configuration

pub fn wkuppupd6(&self) -> WKUPPUPD6R

Bits 26:27 - Wakeup pin pull configuration for WKUP(truncate(n/2)-7) These bits define the I/O pad pull configuration used when WKUPEN(truncate(n/2)-7) = 1. The associated GPIO port pull configuration shall be set to the same value or to 00. The Wakeup pin pull configuration is kept in Standby mode.