Struct stm32h7::stm32h743v::sdmmc1::clkcr::R

pub struct R { /* fields omitted */ }

Value read from the register

Methods

impl R

pub fn bits(&self) -> u32

Value of the register as raw bits

pub fn clkdiv(&self) -> CLKDIVR

Bits 0:9 - Clock divide factor This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0). This field defines the divide factor between the input clock (SDMMCCLK) and the output clock (SDMMC_CK): SDMMC_CK frequency = SDMMCCLK / [2 * CLKDIV]. 0xx: etc.. xxx: etc..

pub fn pwrsav(&self) -> PWRSAVR

Bit 12 - Power saving configuration bit This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) For power saving, the SDMMC_CK clock output can be disabled when the bus is idle by setting PWRSAV:

pub fn widbus(&self) -> WIDBUSR

Bits 14:15 - Wide bus mode enable bit This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0)

pub fn negedge(&self) -> NEGEDGER

Bit 16 - SDMMC_CK dephasing selection bit for data and Command. This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0). When clock division = 1 (CLKDIV = 0), this bit has no effect. Data and Command change on SDMMC_CK falling edge. When clock division >1 (CLKDIV > 0) & DDR = 0: - SDMMC_CK edge occurs on SDMMCCLK rising edge. When clock division >1 (CLKDIV > 0) & DDR = 1: - Data changed on the SDMMCCLK falling edge succeeding a SDMMC_CK edge. - SDMMC_CK edge occurs on SDMMCCLK rising edge. - Data changed on the SDMMC_CK falling edge succeeding a SDMMC_CK edge. - SDMMC_CK edge occurs on SDMMCCLK rising edge.

pub fn hwfc_en(&self) -> HWFC_ENR

Bit 17 - Hardware flow control enable This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) When Hardware flow control is enabled, the meaning of the TXFIFOE and RXFIFOF flags change, please see SDMMC status register definition in Section56.8.11.

pub fn ddr(&self) -> DDRR

Bit 18 - Data rate signaling selection This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) DDR rate shall only be selected with 4-bit or 8-bit wide bus mode. (WIDBUS > 00). DDR = 1 has no effect when WIDBUS = 00 (1-bit wide bus). DDR rate shall only be selected with clock division >1. (CLKDIV > 0)

pub fn busspeed(&self) -> BUSSPEEDR

Bit 19 - Bus speed mode selection between DS, HS, SDR12, SDR25 and SDR50, DDR50, SDR104. This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0)

pub fn selclkrx(&self) -> SELCLKRXR

Bits 20:21 - Receive clock selection. These bits can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0)