[−][src]Struct stm32h7::stm32h743::sdmmc1::RegisterBlock
Register block
Fields
power: POWER
0x00 - SDMMC power control register
clkcr: CLKCR
0x04 - The SDMMC_CLKCR register controls the SDMMC_CK output clock, the SDMMC_RX_CLK receive clock, and the bus width.
argr: ARGR
0x08 - The SDMMC_ARGR register contains a 32-bit command argument, which is sent to a card as part of a command message.
cmdr: CMDR
0x0c - The SDMMC_CMDR register contains the command index and command type bits. The command index is sent to a card as part of a command message. The command type bits control the command path state machine (CPSM).
respcmdr: RESPCMDR
0x10 - SDMMC command response register
resp1r: RESP1R
0x14 - The SDMMC_RESP1/2/3/4R registers contain the status of a card, which is part of the received response.
resp2r: RESP2R
0x18 - The SDMMC_RESP1/2/3/4R registers contain the status of a card, which is part of the received response.
resp3r: RESP3R
0x1c - The SDMMC_RESP1/2/3/4R registers contain the status of a card, which is part of the received response.
resp4r: RESP4R
0x20 - The SDMMC_RESP1/2/3/4R registers contain the status of a card, which is part of the received response.
dtimer: DTIMER
0x24 - The SDMMC_DTIMER register contains the data timeout period, in card bus clock periods. A counter loads the value from the SDMMC_DTIMER register, and starts decrementing when the data path state machine (DPSM) enters the Wait_R or Busy state. If the timer reaches 0 while the DPSM is in either of these states, the timeout status flag is set.
dlenr: DLENR
0x28 - The SDMMC_DLENR register contains the number of data bytes to be transferred. The value is loaded into the data counter when data transfer starts.
dctrl: DCTRL
0x2c - The SDMMC_DCTRL register control the data path state machine (DPSM).
dcntr: DCNTR
0x30 - The SDMMC_DCNTR register loads the value from the data length register (see SDMMC_DLENR) when the DPSM moves from the Idle state to the Wait_R or Wait_S state. As data is transferred, the counter decrements the value until it reaches 0. The DPSM then moves to the Idle state and when there has been no error, the data status end flag (DATAEND) is set.
star: STAR
0x34 - The SDMMC_STAR register is a read-only register. It contains two types of flag:Static flags (bits [29,21,11:0]): these bits remain asserted until they are cleared by writing to the SDMMC interrupt Clear register (see SDMMC_ICR)Dynamic flags (bits [20:12]): these bits change state depending on the state of the underlying logic (for example, FIFO full and empty flags are asserted and de-asserted as data while written to the FIFO)
icr: ICR
0x38 - The SDMMC_ICR register is a write-only register. Writing a bit with 1 clears the corresponding bit in the SDMMC_STAR status register.
maskr: MASKR
0x3c - The interrupt mask register determines which status flags generate an interrupt request by setting the corresponding bit to 1.
acktimer: ACKTIMER
0x40 - The SDMMC_ACKTIMER register contains the acknowledgment timeout period, in SDMMC_CK bus clock periods. A counter loads the value from the SDMMC_ACKTIMER register, and starts decrementing when the data path state machine (DPSM) enters the Wait_Ack state. If the timer reaches 0 while the DPSM is in this states, the acknowledgment timeout status flag is set.
idmactrlr: IDMACTRLR
0x50 - The receive and transmit FIFOs can be read or written as 32-bit wide registers. The FIFOs contain 32 entries on 32 sequential addresses. This allows the CPU to use its load and store multiple operands to read from/write to the FIFO.
idmabsizer: IDMABSIZER
0x54 - The SDMMC_IDMABSIZER register contains the buffers size when in double buffer configuration.
idmabase0r: IDMABASE0R
0x58 - The SDMMC_IDMABASE0R register contains the memory buffer base address in single buffer configuration and the buffer 0 base address in double buffer configuration.
idmabase1r: IDMABASE1R
0x5c - The SDMMC_IDMABASE1R register contains the double buffer configuration second buffer memory base address.
fifor: FIFOR
0x80 - The receive and transmit FIFOs can be only read or written as word (32-bit) wide registers. The FIFOs contain 16 entries on sequential addresses. This allows the CPU to use its load and store multiple operands to read from/write to the FIFO.When accessing SDMMC_FIFOR with half word or byte access an AHB bus fault is generated.
ver: VER
0x3f4 - SDMMC IP version register
id: ID
0x3f8 - SDMMC IP identification register
Auto Trait Implementations
Blanket Implementations
impl<T, U> TryFrom<U> for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> Into<U> for T where
U: From<T>,
[src]
U: From<T>,
impl<T> From<T> for T
[src]
impl<T, U> TryInto<U> for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
impl<T> Borrow<T> for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut<T> for T where
T: ?Sized,
[src]
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<T> Same<T> for T
type Output = T
Should always be Self