[−][src]Struct stm32h7::stm32h743::sdmmc1::clkcr::R
Value read from the register
Methods
impl R
[src]
pub fn bits(&self) -> u32
[src]
Value of the register as raw bits
pub fn clkdiv(&self) -> CLKDIVR
[src]
Bits 0:9 - Clock divide factor This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0). This field defines the divide factor between the input clock (SDMMCCLK) and the output clock (SDMMC_CK): SDMMC_CK frequency = SDMMCCLK / [2 * CLKDIV]. 0xx: etc.. xxx: etc..
pub fn pwrsav(&self) -> PWRSAVR
[src]
Bit 12 - Power saving configuration bit This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) For power saving, the SDMMC_CK clock output can be disabled when the bus is idle by setting PWRSAV:
pub fn widbus(&self) -> WIDBUSR
[src]
Bits 14:15 - Wide bus mode enable bit This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0)
pub fn negedge(&self) -> NEGEDGER
[src]
Bit 16 - SDMMC_CK dephasing selection bit for data and Command. This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0). When clock division = 1 (CLKDIV = 0), this bit has no effect. Data and Command change on SDMMC_CK falling edge. When clock division >1 (CLKDIV > 0) & DDR = 0: - SDMMC_CK edge occurs on SDMMCCLK rising edge. When clock division >1 (CLKDIV > 0) & DDR = 1: - Data changed on the SDMMCCLK falling edge succeeding a SDMMC_CK edge. - SDMMC_CK edge occurs on SDMMCCLK rising edge. - Data changed on the SDMMC_CK falling edge succeeding a SDMMC_CK edge. - SDMMC_CK edge occurs on SDMMCCLK rising edge.
pub fn hwfc_en(&self) -> HWFC_ENR
[src]
Bit 17 - Hardware flow control enable This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) When Hardware flow control is enabled, the meaning of the TXFIFOE and RXFIFOF flags change, please see SDMMC status register definition in Section56.8.11.
pub fn ddr(&self) -> DDRR
[src]
Bit 18 - Data rate signaling selection This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) DDR rate shall only be selected with 4-bit or 8-bit wide bus mode. (WIDBUS > 00). DDR = 1 has no effect when WIDBUS = 00 (1-bit wide bus). DDR rate shall only be selected with clock division >1. (CLKDIV > 0)
pub fn busspeed(&self) -> BUSSPEEDR
[src]
Bit 19 - Bus speed mode selection between DS, HS, SDR12, SDR25 and SDR50, DDR50, SDR104. This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0)
pub fn selclkrx(&self) -> SELCLKRXR
[src]
Bits 20:21 - Receive clock selection. These bits can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0)
Auto Trait Implementations
Blanket Implementations
impl<T, U> TryFrom<U> for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> Into<U> for T where
U: From<T>,
[src]
U: From<T>,
impl<T> From<T> for T
[src]
impl<T, U> TryInto<U> for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
impl<T> Borrow<T> for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut<T> for T where
T: ?Sized,
[src]
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<T> Same<T> for T
type Output = T
Should always be Self