pub struct R(_);
Expand description
Register DAC_CR
reader
Implementations
sourceimpl R
impl R
sourcepub fn en1(&self) -> EN1_R
pub fn en1(&self) -> EN1_R
Bit 0 - DAC channel1 enable This bit is set and cleared by software to enable/disable DAC channel1.
sourcepub fn tsel1(&self) -> TSEL1_R
pub fn tsel1(&self) -> TSEL1_R
Bits 2:5 - DAC channel1 trigger selection These bits select the external event used to trigger DAC channel1. Note: Only used if bit TEN1 = 1 (DAC channel1 trigger enabled).
sourcepub fn wave1(&self) -> WAVE1_R
pub fn wave1(&self) -> WAVE1_R
Bits 6:7 - DAC channel1 noise/triangle wave generation enable These bits are set and cleared by software. Note: Only used if bit TEN1 = 1 (DAC channel1 trigger enabled).
sourcepub fn mamp1(&self) -> MAMP1_R
pub fn mamp1(&self) -> MAMP1_R
Bits 8:11 - DAC channel1 mask/amplitude selector These bits are written by software to select mask in wave generation mode or amplitude in triangle generation mode. = 1011: Unmask bits[11:0] of LFSR/ triangle amplitude equal to 4095
sourcepub fn dmaen1(&self) -> DMAEN1_R
pub fn dmaen1(&self) -> DMAEN1_R
Bit 12 - DAC channel1 DMA enable This bit is set and cleared by software.
sourcepub fn dmaudrie1(&self) -> DMAUDRIE1_R
pub fn dmaudrie1(&self) -> DMAUDRIE1_R
Bit 13 - DAC channel1 DMA Underrun Interrupt enable This bit is set and cleared by software.
sourcepub fn cen1(&self) -> CEN1_R
pub fn cen1(&self) -> CEN1_R
Bit 14 - DAC Channel 1 calibration enable This bit is set and cleared by software to enable/disable DAC channel 1 calibration, it can be written only if bit EN1=0 into DAC_CR (the calibration mode can be entered/exit only when the DAC channel is disabled) Otherwise, the write operation is ignored.
sourcepub fn en2(&self) -> EN2_R
pub fn en2(&self) -> EN2_R
Bit 16 - DAC channel2 enable This bit is set and cleared by software to enable/disable DAC channel2.
sourcepub fn tsel2(&self) -> TSEL2_R
pub fn tsel2(&self) -> TSEL2_R
Bits 18:21 - DAC channel2 trigger selection These bits select the external event used to trigger DAC channel2 Note: Only used if bit TEN2 = 1 (DAC channel2 trigger enabled).
sourcepub fn wave2(&self) -> WAVE2_R
pub fn wave2(&self) -> WAVE2_R
Bits 22:23 - DAC channel2 noise/triangle wave generation enable These bits are set/reset by software. 1x: Triangle wave generation enabled Note: Only used if bit TEN2 = 1 (DAC channel2 trigger enabled)
sourcepub fn mamp2(&self) -> MAMP2_R
pub fn mamp2(&self) -> MAMP2_R
Bits 24:27 - DAC channel2 mask/amplitude selector These bits are written by software to select mask in wave generation mode or amplitude in triangle generation mode. = 1011: Unmask bits[11:0] of LFSR/ triangle amplitude equal to 4095
sourcepub fn dmaen2(&self) -> DMAEN2_R
pub fn dmaen2(&self) -> DMAEN2_R
Bit 28 - DAC channel2 DMA enable This bit is set and cleared by software.
sourcepub fn dmaudrie2(&self) -> DMAUDRIE2_R
pub fn dmaudrie2(&self) -> DMAUDRIE2_R
Bit 29 - DAC channel2 DMA underrun interrupt enable This bit is set and cleared by software.
sourcepub fn cen2(&self) -> CEN2_R
pub fn cen2(&self) -> CEN2_R
Bit 30 - DAC Channel 2 calibration enable This bit is set and cleared by software to enable/disable DAC channel 2 calibration, it can be written only if bit EN2=0 into DAC_CR (the calibration mode can be entered/exit only when the DAC channel is disabled) Otherwise, the write operation is ignored.
Methods from Deref<Target = R<DAC_CR_SPEC>>
Trait Implementations
sourceimpl From<R<DAC_CR_SPEC>> for R
impl From<R<DAC_CR_SPEC>> for R
sourcefn from(reader: R<DAC_CR_SPEC>) -> Self
fn from(reader: R<DAC_CR_SPEC>) -> Self
Converts to this type from the input type.
Auto Trait Implementations
Blanket Implementations
sourceimpl<T> BorrowMut<T> for T where
T: ?Sized,
impl<T> BorrowMut<T> for T where
T: ?Sized,
const: unstable · sourcefn borrow_mut(&mut self) -> &mut T
fn borrow_mut(&mut self) -> &mut T
Mutably borrows from an owned value. Read more