pub struct W(/* private fields */);Expand description
Register DAC_CR writer
Implementations§
Source§impl W
impl W
Sourcepub fn en1(&mut self) -> EN1_W<'_>
pub fn en1(&mut self) -> EN1_W<'_>
Bit 0 - DAC channel1 enable This bit is set and cleared by software to enable/disable DAC channel1.
Sourcepub fn tsel1(&mut self) -> TSEL1_W<'_>
pub fn tsel1(&mut self) -> TSEL1_W<'_>
Bits 2:5 - DAC channel1 trigger selection These bits select the external event used to trigger DAC channel1. Note: Only used if bit TEN1 = 1 (DAC channel1 trigger enabled).
Sourcepub fn wave1(&mut self) -> WAVE1_W<'_>
pub fn wave1(&mut self) -> WAVE1_W<'_>
Bits 6:7 - DAC channel1 noise/triangle wave generation enable These bits are set and cleared by software. Note: Only used if bit TEN1 = 1 (DAC channel1 trigger enabled).
Sourcepub fn mamp1(&mut self) -> MAMP1_W<'_>
pub fn mamp1(&mut self) -> MAMP1_W<'_>
Bits 8:11 - DAC channel1 mask/amplitude selector These bits are written by software to select mask in wave generation mode or amplitude in triangle generation mode. = 1011: Unmask bits[11:0] of LFSR/ triangle amplitude equal to 4095
Sourcepub fn dmaen1(&mut self) -> DMAEN1_W<'_>
pub fn dmaen1(&mut self) -> DMAEN1_W<'_>
Bit 12 - DAC channel1 DMA enable This bit is set and cleared by software.
Sourcepub fn dmaudrie1(&mut self) -> DMAUDRIE1_W<'_>
pub fn dmaudrie1(&mut self) -> DMAUDRIE1_W<'_>
Bit 13 - DAC channel1 DMA Underrun Interrupt enable This bit is set and cleared by software.
Sourcepub fn cen1(&mut self) -> CEN1_W<'_>
pub fn cen1(&mut self) -> CEN1_W<'_>
Bit 14 - DAC Channel 1 calibration enable This bit is set and cleared by software to enable/disable DAC channel 1 calibration, it can be written only if bit EN1=0 into DAC_CR (the calibration mode can be entered/exit only when the DAC channel is disabled) Otherwise, the write operation is ignored.
Sourcepub fn en2(&mut self) -> EN2_W<'_>
pub fn en2(&mut self) -> EN2_W<'_>
Bit 16 - DAC channel2 enable This bit is set and cleared by software to enable/disable DAC channel2.
Sourcepub fn tsel2(&mut self) -> TSEL2_W<'_>
pub fn tsel2(&mut self) -> TSEL2_W<'_>
Bits 18:21 - DAC channel2 trigger selection These bits select the external event used to trigger DAC channel2 Note: Only used if bit TEN2 = 1 (DAC channel2 trigger enabled).
Sourcepub fn wave2(&mut self) -> WAVE2_W<'_>
pub fn wave2(&mut self) -> WAVE2_W<'_>
Bits 22:23 - DAC channel2 noise/triangle wave generation enable These bits are set/reset by software. 1x: Triangle wave generation enabled Note: Only used if bit TEN2 = 1 (DAC channel2 trigger enabled)
Sourcepub fn mamp2(&mut self) -> MAMP2_W<'_>
pub fn mamp2(&mut self) -> MAMP2_W<'_>
Bits 24:27 - DAC channel2 mask/amplitude selector These bits are written by software to select mask in wave generation mode or amplitude in triangle generation mode. = 1011: Unmask bits[11:0] of LFSR/ triangle amplitude equal to 4095
Sourcepub fn dmaen2(&mut self) -> DMAEN2_W<'_>
pub fn dmaen2(&mut self) -> DMAEN2_W<'_>
Bit 28 - DAC channel2 DMA enable This bit is set and cleared by software.
Sourcepub fn dmaudrie2(&mut self) -> DMAUDRIE2_W<'_>
pub fn dmaudrie2(&mut self) -> DMAUDRIE2_W<'_>
Bit 29 - DAC channel2 DMA underrun interrupt enable This bit is set and cleared by software.
Sourcepub fn cen2(&mut self) -> CEN2_W<'_>
pub fn cen2(&mut self) -> CEN2_W<'_>
Bit 30 - DAC Channel 2 calibration enable This bit is set and cleared by software to enable/disable DAC channel 2 calibration, it can be written only if bit EN2=0 into DAC_CR (the calibration mode can be entered/exit only when the DAC channel is disabled) Otherwise, the write operation is ignored.
Methods from Deref<Target = W<DAC_CR_SPEC>>§
Sourcepub unsafe fn bits(&mut self, bits: <REG as RegisterSpec>::Ux) -> &mut W<REG>
pub unsafe fn bits(&mut self, bits: <REG as RegisterSpec>::Ux) -> &mut W<REG>
Writes raw bits to the register.