[−][src]Struct stm32f1xx_hal::gpio::gpioe::PE3

pub struct PE3<MODE> { /* fields omitted */ }

Pin

Methods

impl<MODE> PE3<MODE>[src]

pub fn into_alternate_push_pull(self, cr: &mut CRL) -> PE3<Alternate<PushPull>>[src]

Configures the pin to operate as an alternate function push-pull output pin.

pub fn into_alternate_open_drain(
    self,
    cr: &mut CRL
) -> PE3<Alternate<OpenDrain>>[src]

Configures the pin to operate as an alternate function open-drain output pin.

pub fn into_floating_input(self, cr: &mut CRL) -> PE3<Input<Floating>>[src]

Configures the pin to operate as a floating input pin

pub fn into_pull_down_input(self, cr: &mut CRL) -> PE3<Input<PullDown>>[src]

Configures the pin to operate as a pulled down input pin

pub fn into_pull_up_input(self, cr: &mut CRL) -> PE3<Input<PullUp>>[src]

Configures the pin to operate as a pulled up input pin

pub fn into_open_drain_output(self, cr: &mut CRL) -> PE3<Output<OpenDrain>>[src]

Configures the pin to operate as an open-drain output pin. Initial state will be low.

pub fn into_open_drain_output_with_state(
    self,
    cr: &mut CRL,
    initial_state: State
) -> PE3<Output<OpenDrain>>[src]

Configures the pin to operate as an open-drain output pin. initial_state specifies whether the pin should be initially high or low.

pub fn into_push_pull_output(self, cr: &mut CRL) -> PE3<Output<PushPull>>[src]

Configures the pin to operate as an push-pull output pin. Initial state will be low.

pub fn into_push_pull_output_with_state(
    self,
    cr: &mut CRL,
    initial_state: State
) -> PE3<Output<PushPull>>[src]

Configures the pin to operate as an push-pull output pin. initial_state specifies whether the pin should be initially high or low.

pub fn into_analog(self, cr: &mut CRL) -> PE3<Analog>[src]

Configures the pin to operate as an analog input pin

impl<MODE> PE3<MODE>[src]

pub fn downgrade(self) -> PEx<MODE>[src]

Erases the pin number from the type

This is useful when you want to collect the pins into an array where you need all the elements to have the same type

Trait Implementations

impl<MODE> OutputPin for PE3<Output<MODE>>[src]

impl<MODE> OutputPin for PE3<Alternate<MODE>>[src]

impl<MODE> StatefulOutputPin for PE3<Output<MODE>>[src]

impl<MODE> StatefulOutputPin for PE3<Alternate<MODE>>[src]

impl<MODE> Default for PE3<Output<MODE>>[src]

impl<MODE> InputPin for PE3<Input<MODE>>[src]

impl InputPin for PE3<Output<OpenDrain>>[src]

Auto Trait Implementations

impl<MODE> Send for PE3<MODE> where
    MODE: Send, 

impl<MODE> Sync for PE3<MODE> where
    MODE: Sync, 

Blanket Implementations

impl<T, U> TryFrom for T where
    U: Into<T>, [src]

type Error = Infallible

The type returned in the event of a conversion error.

impl<T> From for T[src]

impl<T, U> TryInto for T where
    U: TryFrom<T>, [src]

type Error = <U as TryFrom<T>>::Error

The type returned in the event of a conversion error.

impl<T, U> Into for T where
    U: From<T>, [src]

impl<T> Borrow for T where
    T: ?Sized, [src]

impl<T> BorrowMut for T where
    T: ?Sized, [src]

impl<T> Any for T where
    T: 'static + ?Sized, [src]

impl<P> ToggleableOutputPin for P where
    P: Default, [src]

fn toggle(&mut self)[src]

Toggle pin output

impl<T> Same for T

type Output = T

Should always be Self