stm32f1_hal/timer/

timer1.rs

type TimerX = pac::TIM1;
type Width = u16;

// sync begin

use super::*;
use crate::{Mcu, pac};

impl Instance for TimerX {}

impl TimerInit<TimerX> for TimerX {
    fn constrain(self, mcu: &mut Mcu) -> Timer<TimerX> {
        Timer::new(self, mcu)
    }
}

impl GeneralTimer for TimerX {
    #[inline(always)]
    fn reset_config(&mut self) {
        self.cr1().reset();
    }

    #[inline(always)]
    fn enable_counter(&mut self) {
        self.cr1().modify(|_, w| w.cen().set_bit());
    }

    #[inline(always)]
    fn disable_counter(&mut self) {
        self.cr1().modify(|_, w| w.cen().clear_bit());
    }

    #[inline(always)]
    fn is_counter_enabled(&self) -> bool {
        self.cr1().read().cen().is_enabled()
    }

    #[inline(always)]
    fn reset_counter(&mut self) {
        self.cnt().reset();
    }

    #[inline(always)]
    fn max_auto_reload() -> u32 {
        Width::MAX as u32
    }

    #[inline(always)]
    unsafe fn set_auto_reload_unchecked(&mut self, arr: u32) {
        unsafe {
            self.arr().write(|w| w.bits(arr));
        }
    }

    #[inline(always)]
    fn set_auto_reload(&mut self, arr: u32) -> Result<(), Error> {
        // Note: Make it impossible to set the ARR value to 0, since this
        // would cause an infinite loop.
        if arr > 0 && arr <= Self::max_auto_reload() {
            unsafe { self.set_auto_reload_unchecked(arr) }
            Ok(())
        } else {
            Err(Error::WrongAutoReload)
        }
    }

    #[inline(always)]
    fn read_auto_reload(&self) -> u32 {
        self.arr().read().bits()
    }

    #[inline(always)]
    fn set_prescaler(&mut self, psc: u16) {
        self.psc().write(|w| w.psc().set(psc));
    }

    #[inline(always)]
    fn read_prescaler(&self) -> u16 {
        self.psc().read().psc().bits()
    }

    #[inline(always)]
    fn read_count(&self) -> u32 {
        self.cnt().read().bits()
    }

    #[inline(always)]
    fn trigger_update(&mut self) {
        // Sets the URS bit to prevent an interrupt from being triggered by
        // the UG bit
        self.cr1().modify(|_, w| w.urs().set_bit());
        self.egr().write(|w| w.ug().set_bit());
        self.cr1().modify(|_, w| w.urs().clear_bit());
    }

    #[inline]
    fn config_freq(&mut self, clock: Hertz, update_freq: Hertz) {
        let (prescaler, arr) = compute_prescaler_arr(clock.raw(), update_freq.raw());
        self.set_prescaler(prescaler as u16);
        self.set_auto_reload(arr).unwrap();
        // Trigger update event to load the registers
        self.trigger_update();
    }

    #[inline(always)]
    fn clear_interrupt_flag(&mut self, event: Event) {
        self.sr()
            .write(|w| unsafe { w.bits(0xffff & !event.bits()) });
    }

    #[inline(always)]
    fn listen_interrupt(&mut self, event: Event, b: bool) {
        self.dier().modify(|r, w| unsafe {
            w.bits(if b {
                r.bits() | event.bits()
            } else {
                r.bits() & !event.bits()
            })
        });
    }

    #[inline(always)]
    fn get_interrupt_flag(&self) -> Event {
        Event::from_bits_truncate(self.sr().read().bits())
    }

    #[inline(always)]
    fn start_one_pulse(&mut self) {
        self.cr1().modify(|_, w| w.opm().set_bit().cen().set_bit());
    }

    #[inline(always)]
    fn stop_in_debug(&mut self, state: bool) {
        let dbg = unsafe { DBG::steal() };
        // sync dbg_t1
        dbg.cr().modify(|_, w| w.dbg_tim1_stop().bit(state));
        // sync dbg_end
    }

    #[inline(always)]
    fn enable_preload(&mut self, b: bool) {
        self.cr1().modify(|_, w| w.arpe().bit(b));
    }
}

// sync pwm
// PWM ------------------------------------------------------------------------

impl TimerWithPwm for TimerX {
    fn stop_pwm(&mut self) {
        self.disable_counter();
    }

    // sync start_pwm_aoe

    #[inline(always)]
    fn start_pwm(&mut self) {
        // self.bdtr().modify(|_, w| w.moe().set_bit());
        self.bdtr().modify(|_, w| w.aoe().set_bit());
        self.reset_counter();
        self.enable_counter();
    }

    // sync pwm_cfg_4

    #[inline(always)]
    fn preload_output_channel_in_mode(&mut self, channel: Channel, mode: PwmMode) {
        let mode = Ocm::from(mode);
        match channel {
            Channel::C1 => {
                self.ccmr1_output()
                    .modify(|_, w| w.oc1pe().set_bit().oc1m().set(mode as _));
            }
            Channel::C2 => {
                self.ccmr1_output()
                    .modify(|_, w| w.oc2pe().set_bit().oc2m().set(mode as _));
            }
            Channel::C3 => {
                self.ccmr2_output()
                    .modify(|_, w| w.oc3pe().set_bit().oc3m().set(mode as _));
            }
            Channel::C4 => {
                self.ccmr2_output()
                    .modify(|_, w| w.oc4pe().set_bit().oc4m().set(mode as _));
            }
        }
    }

    fn set_polarity(&mut self, channel: Channel, polarity: PwmPolarity) {
        match channel {
            Channel::C1 => {
                self.ccer()
                    .modify(|_, w| w.cc1p().bit(polarity == PwmPolarity::ActiveLow));
            }
            Channel::C2 => {
                self.ccer()
                    .modify(|_, w| w.cc2p().bit(polarity == PwmPolarity::ActiveLow));
            }
            Channel::C3 => {
                self.ccer()
                    .modify(|_, w| w.cc3p().bit(polarity == PwmPolarity::ActiveLow));
            }
            Channel::C4 => {
                self.ccer()
                    .modify(|_, w| w.cc4p().bit(polarity == PwmPolarity::ActiveLow));
            }
        }
    }
}

// sync pwm_ch1
// PWM Channels ---------------------------------------------------------------

impl TimerWithPwm1Ch for TimerX {
    #[inline(always)]
    fn enable_ch1(&mut self, en: bool) {
        self.ccer().modify(|_, w| w.cc1e().bit(en));
    }

    #[inline(always)]
    fn set_ch1_cc_value(&mut self, value: u32) {
        unsafe { self.ccr1().write(|w| w.bits(value)) };
    }

    #[inline(always)]
    fn get_ch1_cc_value(&self) -> u32 {
        self.ccr1().read().bits()
    }
}

// sync pwm_ch2

impl TimerWithPwm2Ch for TimerX {
    #[inline(always)]
    fn enable_ch2(&mut self, en: bool) {
        self.ccer().modify(|_, w| w.cc2e().bit(en));
    }

    #[inline(always)]
    fn set_ch2_cc_value(&mut self, value: u32) {
        unsafe { self.ccr2().write(|w| w.bits(value)) };
    }

    #[inline(always)]
    fn get_ch2_cc_value(&self) -> u32 {
        self.ccr2().read().bits()
    }
}

// sync pwm_ch4

impl TimerWithPwm3Ch for TimerX {
    #[inline(always)]
    fn enable_ch3(&mut self, en: bool) {
        self.ccer().modify(|_, w| w.cc3e().bit(en));
    }

    #[inline(always)]
    fn set_ch3_cc_value(&mut self, value: u32) {
        unsafe { self.ccr3().write(|w| w.bits(value)) };
    }

    #[inline(always)]
    fn get_ch3_cc_value(&self) -> u32 {
        self.ccr3().read().bits()
    }
}

impl TimerWithPwm4Ch for TimerX {
    #[inline(always)]
    fn enable_ch4(&mut self, en: bool) {
        self.ccer().modify(|_, w| w.cc4e().bit(en));
    }

    #[inline(always)]
    fn set_ch4_cc_value(&mut self, value: u32) {
        unsafe { self.ccr4().write(|w| w.bits(value)) };
    }

    #[inline(always)]
    fn get_ch4_cc_value(&self) -> u32 {
        self.ccr4().read().bits()
    }
}

// Other ----------------------------------------------------------------------

// sync master
impl MasterTimer for TimerX {
    #[inline(always)]
    fn master_mode(&mut self, mode: MasterMode) {
        self.cr2().modify(|_, w| w.mms().variant(mode.into()));
    }
}

// sync dir

impl TimerDirection for TimerX {
    #[inline(always)]
    fn set_count_direction(&mut self, dir: CountDirection) {
        self.cr1()
            .modify(|_, w| w.dir().bit(dir == CountDirection::Down));
    }
}

// sync RTIC
#[cfg(feature = "rtic")]
mod timer_rtic {
    use super::*;
    use crate::Mcu;
    use rtic_monotonic::Monotonic;

    impl MonoTimerExt for TimerX {
        fn monotonic<const FREQ: u32>(self, mcu: &mut Mcu) -> MonoTimer<Self, FREQ> {
            mcu.rcc.enable(&self);
            mcu.rcc.reset(&self);
            let clk = mcu.rcc.get_timer_clock(&self);
            FTimer::new(self, clk).monotonic()
        }
    }

    impl<const FREQ: u32> FTimer<TimerX, FREQ> {
        pub fn monotonic(self) -> MonoTimer<TimerX, FREQ> {
            MonoTimer::<TimerX, FREQ>::_new(self)
        }
    }

    impl<const FREQ: u32> MonoTimer<TimerX, FREQ> {
        fn _new(timer: FTimer<TimerX, FREQ>) -> Self {
            // Set auto-reload value.
            timer.tim.arr().write(|w| w.arr().set(u16::MAX));
            // Generate interrupt on overflow.
            timer.tim.egr().write(|w| w.ug().set_bit());

            // Start timer.
            // Clear interrupt flag.
            timer.tim.sr().modify(|_, w| w.uif().clear_bit());
            timer.tim.cr1().modify(|_, w| {
                // Enable counter.
                w.cen().set_bit();
                // Overflow should trigger update event.
                w.udis().clear_bit();
                // Only overflow triggers interrupt.
                w.urs().set_bit()
            });

            Self { timer, ovf: 0 }
        }
    }

    impl<const FREQ: u32> Monotonic for MonoTimer<TimerX, FREQ> {
        type Instant = fugit::TimerInstantU32<FREQ>;
        type Duration = fugit::TimerDurationU32<FREQ>;

        unsafe fn reset(&mut self) {
            self.tim.dier().modify(|_, w| w.cc1ie().set_bit());
        }

        #[inline(always)]
        fn now(&mut self) -> Self::Instant {
            let cnt = self.tim.cnt().read().cnt().bits() as u32;

            // If the overflow bit is set, we add this to the timer value. It means the `on_interrupt`
            // has not yet happened, and we need to compensate here.
            let ovf = if self.tim.sr().read().uif().bit_is_set() {
                0x10000
            } else {
                0
            };

            Self::Instant::from_ticks(cnt.wrapping_add(ovf).wrapping_add(self.ovf))
        }

        fn set_compare(&mut self, instant: Self::Instant) {
            let now = self.now();
            let cnt = self.tim.cnt().read().cnt().bits();

            // Since the timer may or may not overflow based on the requested compare val, we check
            // how many ticks are left.
            let val = match instant.checked_duration_since(now) {
                None => cnt.wrapping_add(0xffff), // In the past, RTIC will handle this
                Some(x) if x.ticks() <= 0xffff => instant.duration_since_epoch().ticks() as u16, // Will not overflow
                Some(_) => cnt.wrapping_add(0xffff), // Will overflow, run for as long as possible
            };

            self.tim.ccr1().write(|w| w.ccr().set(val));
        }

        fn clear_compare_flag(&mut self) {
            self.tim.sr().modify(|_, w| w.cc1if().clear_bit());
        }

        fn on_interrupt(&mut self) {
            // If there was an overflow, increment the overflow counter.
            if self.tim.sr().read().uif().bit_is_set() {
                self.tim.sr().modify(|_, w| w.uif().clear_bit());

                self.ovf += 0x10000;
            }
        }

        #[inline(always)]
        fn zero() -> Self::Instant {
            Self::Instant::from_ticks(0)
        }
    }
}

// sync end

use pac::tim1::cr2::MMS;
impl From<MasterMode> for MMS {
    fn from(value: MasterMode) -> Self {
        match value {
            MasterMode::Reset => MMS::Reset,
            MasterMode::Enable => MMS::Enable,
            MasterMode::Update => MMS::Update,
            MasterMode::ComparePulse => MMS::ComparePulse,
            MasterMode::CompareOc1 => MMS::CompareOc1,
            MasterMode::CompareOc2 => MMS::CompareOc2,
            MasterMode::CompareOc3 => MMS::CompareOc3,
            MasterMode::CompareOc4 => MMS::CompareOc4,
        }
    }
}