Struct stm32_metapac::pwr::regs::Cr2

#[repr(transparent)]
pub struct Cr2(pub u32);
Expand description

This register is not reset by wakeup from Standby mode, RESET signal and VDD POR. It is only reset by VSW POR and VSWRST reset. This register shall not be accessed when VSWRST bit in RCC_BDCR register resets the VSW domain.After reset, PWR_CR2 register is write-protected. Prior to modifying its content, the DBP bit in PWR_CR1 register must be set to disable the write protection.

Tuple Fields§

§0: u32

Implementations§

§

impl Cr2

pub const fn bren(&self) -> bool

Backup regulator enable When set, the Backup regulator (used to maintain the backup RAM content in Standby and VBAT modes) is enabled. If BREN is reset, the backup regulator is switched off. The backup RAM can still be used in Run and Stop modes. However, its content will be lost in Standby and VBAT modes. If BREN is set, the application must wait till the Backup Regulator Ready flag (BRRDY) is set to indicate that the data written into the SRAM will be maintained in Standby and VBAT modes.

pub fn set_bren(&mut self, val: bool)

Backup regulator enable When set, the Backup regulator (used to maintain the backup RAM content in Standby and VBAT modes) is enabled. If BREN is reset, the backup regulator is switched off. The backup RAM can still be used in Run and Stop modes. However, its content will be lost in Standby and VBAT modes. If BREN is set, the application must wait till the Backup Regulator Ready flag (BRRDY) is set to indicate that the data written into the SRAM will be maintained in Standby and VBAT modes.

pub const fn monen(&self) -> bool

VBAT and temperature monitoring enable When set, the VBAT supply and temperature monitoring is enabled.

pub fn set_monen(&mut self, val: bool)

VBAT and temperature monitoring enable When set, the VBAT supply and temperature monitoring is enabled.

pub const fn brrdy(&self) -> bool

Backup regulator ready This bit is set by hardware to indicate that the Backup regulator is ready.

pub fn set_brrdy(&mut self, val: bool)

Backup regulator ready This bit is set by hardware to indicate that the Backup regulator is ready.

pub const fn vbatl(&self) -> bool

VBAT level monitoring versus low threshold

pub fn set_vbatl(&mut self, val: bool)

VBAT level monitoring versus low threshold

pub const fn vbath(&self) -> bool

VBAT level monitoring versus high threshold

pub fn set_vbath(&mut self, val: bool)

VBAT level monitoring versus high threshold

pub const fn templ(&self) -> bool

Temperature level monitoring versus low threshold

pub fn set_templ(&mut self, val: bool)

Temperature level monitoring versus low threshold

pub const fn temph(&self) -> bool

Temperature level monitoring versus high threshold

pub fn set_temph(&mut self, val: bool)

Temperature level monitoring versus high threshold

Trait Implementations§

§

impl Clone for Cr2

§

fn clone(&self) -> Cr2

Returns a copy of the value. Read more
1.0.0 · source§

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source. Read more
§

impl Default for Cr2

§

fn default() -> Cr2

Returns the “default value” for a type. Read more
§

impl PartialEq for Cr2

§

fn eq(&self, other: &Cr2) -> bool

This method tests for self and other values to be equal, and is used by ==.
1.0.0 · source§

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.
§

impl Copy for Cr2

§

impl Eq for Cr2

§

impl StructuralEq for Cr2

§

impl StructuralPartialEq for Cr2

Auto Trait Implementations§

§

impl RefUnwindSafe for Cr2

§

impl Send for Cr2

§

impl Sync for Cr2

§

impl Unpin for Cr2

§

impl UnwindSafe for Cr2

Blanket Implementations§

source§

impl<T> Any for T
where T: 'static + ?Sized,

source§

fn type_id(&self) -> TypeId

Gets the TypeId of self. Read more
source§

impl<T> Borrow<T> for T
where T: ?Sized,

source§

fn borrow(&self) -> &T

Immutably borrows from an owned value. Read more
source§

impl<T> BorrowMut<T> for T
where T: ?Sized,

source§

fn borrow_mut(&mut self) -> &mut T

Mutably borrows from an owned value. Read more
source§

impl<T> From<T> for T

source§

fn from(t: T) -> T

Returns the argument unchanged.

source§

impl<T, U> Into<U> for T
where U: From<T>,

source§

fn into(self) -> U

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

source§

impl<T, U> TryFrom<U> for T
where U: Into<T>,

§

type Error = Infallible

The type returned in the event of a conversion error.
source§

fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>

Performs the conversion.
source§

impl<T, U> TryInto<U> for T
where U: TryFrom<T>,

§

type Error = <U as TryFrom<T>>::Error

The type returned in the event of a conversion error.
source§

fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>

Performs the conversion.