Trait probe_rs::architecture::arm::RawDapAccess

pub trait RawDapAccess {
    // Required methods
    fn raw_read_register(
        &mut self,
        port: PortType,
        addr: u8
    ) -> Result<u32, ArmError>;
    fn raw_write_register(
        &mut self,
        port: PortType,
        addr: u8,
        value: u32
    ) -> Result<(), ArmError>;
    fn jtag_sequence(
        &mut self,
        cycles: u8,
        tms: bool,
        tdi: u64
    ) -> Result<(), DebugProbeError>;
    fn swj_sequence(
        &mut self,
        bit_len: u8,
        bits: u64
    ) -> Result<(), DebugProbeError>;
    fn swj_pins(
        &mut self,
        pin_out: u32,
        pin_select: u32,
        pin_wait: u32
    ) -> Result<u32, DebugProbeError>;
    fn into_probe(self: Box<Self>) -> Box<dyn DebugProbe>;
    fn core_status_notification(
        &mut self,
        state: CoreStatus
    ) -> Result<(), DebugProbeError>;

    // Provided methods
    fn raw_read_block(
        &mut self,
        port: PortType,
        addr: u8,
        values: &mut [u32]
    ) -> Result<(), ArmError> { ... }
    fn raw_write_block(
        &mut self,
        port: PortType,
        addr: u8,
        values: &[u32]
    ) -> Result<(), ArmError> { ... }
    fn raw_flush(&mut self) -> Result<(), ArmError> { ... }
    fn configure_jtag(&mut self) -> Result<(), DebugProbeError> { ... }
}

Low-level DAP register access.

Operations on this trait closely match the transactions on the wire. Implementors only do basic error handling, such as retrying WAIT errors.

Almost everything is the responsibility of the caller. For example, the caller must handle bank switching and AP selection.

Required Methods

fn raw_read_register( &mut self, port: PortType, addr: u8 ) -> Result<u32, ArmError>

Read a DAP register.

Only the lowest 4 bits of addr are used. Bank switching is the caller’s responsibility.

fn raw_write_register( &mut self, port: PortType, addr: u8, value: u32 ) -> Result<(), ArmError>

Write a value to a DAP register.

Only the lowest 4 bits of addr are used. Bank switching is the caller’s responsibility.

fn jtag_sequence( &mut self, cycles: u8, tms: bool, tdi: u64 ) -> Result<(), DebugProbeError>

Send a specific output sequence over JTAG.

This can only be used for output, and should be used to generate the initial reset sequence, for example.

fn swj_sequence( &mut self, bit_len: u8, bits: u64 ) -> Result<(), DebugProbeError>

Send a specific output sequence over JTAG or SWD.

This can only be used for output, and should be used to generate the initial reset sequence, for example.

fn swj_pins( &mut self, pin_out: u32, pin_select: u32, pin_wait: u32 ) -> Result<u32, DebugProbeError>

Set the state of debugger output pins directly.

The bits have the following meaning:

Bit 0: SWCLK/TCK Bit 1: SWDIO/TMS Bit 2: TDI Bit 3: TDO Bit 5: nTRST Bit 7: nRESET

fn into_probe(self: Box<Self>) -> Box<dyn DebugProbe>

Cast this interface into a generic DebugProbe.

fn core_status_notification( &mut self, state: CoreStatus ) -> Result<(), DebugProbeError>

Inform the probe of the CoreStatus of the chip attached to the probe.

Provided Methods

fn raw_read_block( &mut self, port: PortType, addr: u8, values: &mut [u32] ) -> Result<(), ArmError>

Read multiple values from the same DAP register.

If possible, this uses optimized read functions, otherwise it falls back to the read_register function.

Only the lowest 4 bits of addr are used. Bank switching is the caller’s responsibility.

fn raw_write_block( &mut self, port: PortType, addr: u8, values: &[u32] ) -> Result<(), ArmError>

Write multiple values to the same DAP register.

If possible, this uses optimized write functions, otherwise it falls back to the write_register function.

Only the lowest 4 bits of addr are used. Bank switching is the caller’s responsibility.

fn raw_flush(&mut self) -> Result<(), ArmError>

Flush any outstanding writes.

By default, this does nothing – but in probes that implement write batching, this needs to flush any pending writes.

fn configure_jtag(&mut self) -> Result<(), DebugProbeError>

Configures the probe for JTAG use (specifying IR lengths of each DAP).

Implementors

impl RawDapAccess for CmsisDap

impl RawDapAccess for FakeProbe

impl<Probe: DebugProbe + RawProtocolIo + JTAGAccess + 'static> RawDapAccess for Probe