Struct probe_rs::architecture::arm::m33::M33

pub struct M33<'probe> { /* fields omitted */ }

Trait Implementations

impl<'probe> CoreInterface for M33<'probe>

fn get_hw_breakpoints(&mut self) -> Result<Vec<Option<u32>>, Error>

See docs on the CoreInterface::get_hw_breakpoints trait

fn wait_for_core_halted(&mut self, timeout: Duration) -> Result<(), Error>

Wait until the core is halted. If the core does not halt on its own, a [DebugProbeError::Timeout] error will be returned.

fn core_halted(&mut self) -> Result<bool, Error>

Check if the core is halted. If the core does not halt on its own, a [DebugProbeError::Timeout] error will be returned.

fn halt(&mut self, timeout: Duration) -> Result<CoreInformation, Error>

Try to halt the core. This function ensures the core is actually halted, and returns a [DebugProbeError::Timeout] otherwise.

fn run(&mut self) -> Result<(), Error>

fn reset(&mut self) -> Result<(), Error>

Reset the core, and then continue to execute instructions. If the core should be halted after reset, use the reset_and_halt function.

fn reset_and_halt(
    &mut self,
    timeout: Duration
) -> Result<CoreInformation, Error>

Reset the core, and then immediately halt. To continue execution after reset, use the reset function.

fn step(&mut self) -> Result<CoreInformation, Error>

Steps one instruction and then enters halted state again.

fn read_core_reg(&mut self, address: CoreRegisterAddress) -> Result<u32, Error>

fn write_core_reg(
    &mut self,
    address: CoreRegisterAddress,
    value: u32
) -> Result<()>

fn get_available_breakpoint_units(&mut self) -> Result<u32, Error>

fn enable_breakpoints(&mut self, state: bool) -> Result<(), Error>

fn set_hw_breakpoint(
    &mut self,
    bp_unit_index: usize,
    addr: u32
) -> Result<(), Error>

fn registers(&self) -> &'static RegisterFile

fn clear_hw_breakpoint(&mut self, bp_unit_index: usize) -> Result<(), Error>

fn hw_breakpoints_enabled(&self) -> bool

fn architecture(&self) -> Architecture

Get the Architecture of the Core.

fn status(&mut self) -> Result<CoreStatus, Error>

impl<'probe> MemoryInterface for M33<'probe>

fn read_word_32(&mut self, address: u32) -> Result<u32, Error>

Read a 32bit word of at address.

fn read_word_8(&mut self, address: u32) -> Result<u8, Error>

Read an 8bit word of at address.

fn read_32(&mut self, address: u32, data: &mut [u32]) -> Result<(), Error>

Read a block of 32bit words at address.

fn read_8(&mut self, address: u32, data: &mut [u8]) -> Result<(), Error>

Read a block of 8bit words at address.

fn write_word_32(&mut self, address: u32, data: u32) -> Result<(), Error>

Write a 32bit word at address.

fn write_word_8(&mut self, address: u32, data: u8) -> Result<(), Error>

Write an 8bit word at address.

fn write_32(&mut self, address: u32, data: &[u32]) -> Result<(), Error>

Write a block of 32bit words at address.

fn write_8(&mut self, address: u32, data: &[u8]) -> Result<(), Error>

Write a block of 8bit words at address.

fn flush(&mut self) -> Result<(), Error>

Flush any outstanding operations.

fn read_mem_32bit(&mut self, address: u32, data: &mut [u8]) -> Result<(), Error>

Reads bytes using 32 bit memory access. Address must be 32 bit aligned and data must be an exact multiple of 4.

fn read(&mut self, address: u32, data: &mut [u8]) -> Result<(), Error>

Read a block of 8bit words at address. May use 32 bit memory access, so should only be used if reading memory locations that don’t have side effects. Generally faster than read_8.