Struct nrf5340_app_pac::saadc_ns::RegisterBlock

#[repr(C)]
pub struct RegisterBlock {
    pub tasks_start: TASKS_START,
    pub tasks_sample: TASKS_SAMPLE,
    pub tasks_stop: TASKS_STOP,
    pub tasks_calibrateoffset: TASKS_CALIBRATEOFFSET,
    pub subscribe_start: SUBSCRIBE_START,
    pub subscribe_sample: SUBSCRIBE_SAMPLE,
    pub subscribe_stop: SUBSCRIBE_STOP,
    pub subscribe_calibrateoffset: SUBSCRIBE_CALIBRATEOFFSET,
    pub events_started: EVENTS_STARTED,
    pub events_end: EVENTS_END,
    pub events_done: EVENTS_DONE,
    pub events_resultdone: EVENTS_RESULTDONE,
    pub events_calibratedone: EVENTS_CALIBRATEDONE,
    pub events_stopped: EVENTS_STOPPED,
    pub events_ch: [EVENTS_CH; 8],
    pub publish_started: PUBLISH_STARTED,
    pub publish_end: PUBLISH_END,
    pub publish_done: PUBLISH_DONE,
    pub publish_resultdone: PUBLISH_RESULTDONE,
    pub publish_calibratedone: PUBLISH_CALIBRATEDONE,
    pub publish_stopped: PUBLISH_STOPPED,
    pub publish_ch: [PUBLISH_CH; 8],
    pub inten: INTEN,
    pub intenset: INTENSET,
    pub intenclr: INTENCLR,
    pub status: STATUS,
    pub enable: ENABLE,
    pub ch: [CH; 8],
    pub resolution: RESOLUTION,
    pub oversample: OVERSAMPLE,
    pub samplerate: SAMPLERATE,
    pub result: RESULT,
    // some fields omitted
}

Register block

Fields

tasks_start: TASKS_START

0x00 - Start the ADC and prepare the result buffer in RAM

tasks_sample: TASKS_SAMPLE

0x04 - Take one ADC sample, if scan is enabled all channels are sampled

tasks_stop: TASKS_STOP

0x08 - Stop the ADC and terminate any on-going conversion

tasks_calibrateoffset: TASKS_CALIBRATEOFFSET

0x0c - Starts offset auto-calibration

subscribe_start: SUBSCRIBE_START

0x80 - Subscribe configuration for task START

subscribe_sample: SUBSCRIBE_SAMPLE

0x84 - Subscribe configuration for task SAMPLE

subscribe_stop: SUBSCRIBE_STOP

0x88 - Subscribe configuration for task STOP

subscribe_calibrateoffset: SUBSCRIBE_CALIBRATEOFFSET

0x8c - Subscribe configuration for task CALIBRATEOFFSET

events_started: EVENTS_STARTED

0x100 - The ADC has started

events_end: EVENTS_END

0x104 - The ADC has filled up the Result buffer

events_done: EVENTS_DONE

0x108 - A conversion task has been completed. Depending on the mode, multiple conversions might be needed for a result to be transferred to RAM.

events_resultdone: EVENTS_RESULTDONE

0x10c - A result is ready to get transferred to RAM.

events_calibratedone: EVENTS_CALIBRATEDONE

0x110 - Calibration is complete

events_stopped: EVENTS_STOPPED

0x114 - The ADC has stopped

events_ch: [EVENTS_CH; 8]

0x118 - Peripheral events.

publish_started: PUBLISH_STARTED

0x180 - Publish configuration for event STARTED

publish_end: PUBLISH_END

0x184 - Publish configuration for event END

publish_done: PUBLISH_DONE

0x188 - Publish configuration for event DONE

publish_resultdone: PUBLISH_RESULTDONE

0x18c - Publish configuration for event RESULTDONE

publish_calibratedone: PUBLISH_CALIBRATEDONE

0x190 - Publish configuration for event CALIBRATEDONE

publish_stopped: PUBLISH_STOPPED

0x194 - Publish configuration for event STOPPED

publish_ch: [PUBLISH_CH; 8]

0x198 - Publish configuration for events

inten: INTEN

0x300 - Enable or disable interrupt

intenset: INTENSET

0x304 - Enable interrupt

intenclr: INTENCLR

0x308 - Disable interrupt

status: STATUS

0x400 - Status

enable: ENABLE

0x500 - Enable or disable ADC

ch: [CH; 8]

0x510 - Unspecified

resolution: RESOLUTION

0x5f0 - Resolution configuration

oversample: OVERSAMPLE

0x5f4 - Oversampling configuration. OVERSAMPLE should not be combined with SCAN. The RESOLUTION is applied before averaging, thus for high OVERSAMPLE a higher RESOLUTION should be used.

samplerate: SAMPLERATE

0x5f8 - Controls normal or continuous sample rate

result: RESULT

0x62c - RESULT EasyDMA channel