Struct nrf52810_pac::uarte0::RegisterBlock

#[repr(C)]
pub struct RegisterBlock {
    pub tasks_startrx: TASKS_STARTRX,
    pub tasks_stoprx: TASKS_STOPRX,
    pub tasks_starttx: TASKS_STARTTX,
    pub tasks_stoptx: TASKS_STOPTX,
    pub tasks_flushrx: TASKS_FLUSHRX,
    pub events_cts: EVENTS_CTS,
    pub events_ncts: EVENTS_NCTS,
    pub events_rxdrdy: EVENTS_RXDRDY,
    pub events_endrx: EVENTS_ENDRX,
    pub events_txdrdy: EVENTS_TXDRDY,
    pub events_endtx: EVENTS_ENDTX,
    pub events_error: EVENTS_ERROR,
    pub events_rxto: EVENTS_RXTO,
    pub events_rxstarted: EVENTS_RXSTARTED,
    pub events_txstarted: EVENTS_TXSTARTED,
    pub events_txstopped: EVENTS_TXSTOPPED,
    pub shorts: SHORTS,
    pub inten: INTEN,
    pub intenset: INTENSET,
    pub intenclr: INTENCLR,
    pub errorsrc: ERRORSRC,
    pub enable: ENABLE,
    pub psel: PSEL,
    pub baudrate: BAUDRATE,
    pub rxd: RXD,
    pub txd: TXD,
    pub config: CONFIG,
    // some fields omitted
}

Register block

Fields

tasks_startrx: TASKS_STARTRX

0x00 - Start UART receiver

tasks_stoprx: TASKS_STOPRX

0x04 - Stop UART receiver

tasks_starttx: TASKS_STARTTX

0x08 - Start UART transmitter

tasks_stoptx: TASKS_STOPTX

0x0c - Stop UART transmitter

tasks_flushrx: TASKS_FLUSHRX

0x2c - Flush RX FIFO into RX buffer

events_cts: EVENTS_CTS

0x100 - CTS is activated (set low). Clear To Send.

events_ncts: EVENTS_NCTS

0x104 - CTS is deactivated (set high). Not Clear To Send.

events_rxdrdy: EVENTS_RXDRDY

0x108 - Data received in RXD (but potentially not yet transferred to Data RAM)

events_endrx: EVENTS_ENDRX

0x110 - Receive buffer is filled up

events_txdrdy: EVENTS_TXDRDY

0x11c - Data sent from TXD

events_endtx: EVENTS_ENDTX

0x120 - Last TX byte transmitted

events_error: EVENTS_ERROR

0x124 - Error detected

events_rxto: EVENTS_RXTO

0x144 - Receiver timeout

events_rxstarted: EVENTS_RXSTARTED

0x14c - UART receiver has started

events_txstarted: EVENTS_TXSTARTED

0x150 - UART transmitter has started

events_txstopped: EVENTS_TXSTOPPED

0x158 - Transmitter stopped

shorts: SHORTS

0x200 - Shortcuts between local events and tasks

inten: INTEN

0x300 - Enable or disable interrupt

intenset: INTENSET

0x304 - Enable interrupt

intenclr: INTENCLR

0x308 - Disable interrupt

errorsrc: ERRORSRC

0x480 - Error source Note : this register is read / write one to clear.

enable: ENABLE

0x500 - Enable UART

psel: PSEL

0x508 - Unspecified

baudrate: BAUDRATE

0x524 - Baud rate. Accuracy depends on the HFCLK source selected.

rxd: RXD

0x534 - RXD EasyDMA channel

txd: TXD

0x544 - TXD EasyDMA channel

config: CONFIG

0x56c - Configuration of parity and hardware flow control