pub struct R(_);
Expand description
Register CTRL
reader
Implementations§
source§impl R
impl R
sourcepub fn down_l(&self) -> DOWN_L_R
pub fn down_l(&self) -> DOWN_L_R
Bit 0 - This bit is 1 when the L or unified counter is counting down. Hardware sets this bit when the counter is counting up, counter limit occurs, and BIDIR = 1.Hardware clears this bit when the counter is counting down and a limit condition occurs or when the counter reaches 0.
sourcepub fn stop_l(&self) -> STOP_L_R
pub fn stop_l(&self) -> STOP_L_R
Bit 1 - When this bit is 1 and HALT is 0, the L or unified counter does not run, but I/O events related to the counter can occur. If a designated start event occurs, this bit is cleared and counting resumes.
sourcepub fn halt_l(&self) -> HALT_L_R
pub fn halt_l(&self) -> HALT_L_R
Bit 2 - When this bit is 1, the L or unified counter does not run and no events can occur. A reset sets this bit. When the HALT_L bit is one, the STOP_L bit is cleared. It is possible to remove the halt condition while keeping the SCT in the stop condition (not running) with a single write to this register to simultaneously clear the HALT bit and set the STOP bit. Once set, only software can clear this bit to restore counter operation. This bit is set on reset.
sourcepub fn clrctr_l(&self) -> CLRCTR_L_R
pub fn clrctr_l(&self) -> CLRCTR_L_R
Bit 3 - Writing a 1 to this bit clears the L or unified counter. This bit always reads as 0.
sourcepub fn pre_l(&self) -> PRE_L_R
pub fn pre_l(&self) -> PRE_L_R
Bits 5:12 - Specifies the factor by which the SCT clock is prescaled to produce the L or unified counter clock. The counter clock is clocked at the rate of the SCT clock divided by PRE_L+1. Clear the counter (by writing a 1 to the CLRCTR bit) whenever changing the PRE value.
sourcepub fn down_h(&self) -> DOWN_H_R
pub fn down_h(&self) -> DOWN_H_R
Bit 16 - This bit is 1 when the H counter is counting down. Hardware sets this bit when the counter is counting, a counter limit condition occurs, and BIDIR is 1. Hardware clears this bit when the counter is counting down and a limit condition occurs or when the counter reaches 0.
sourcepub fn stop_h(&self) -> STOP_H_R
pub fn stop_h(&self) -> STOP_H_R
Bit 17 - When this bit is 1 and HALT is 0, the H counter does not, run but I/O events related to the counter can occur. If such an event matches the mask in the Start register, this bit is cleared and counting resumes.
sourcepub fn halt_h(&self) -> HALT_H_R
pub fn halt_h(&self) -> HALT_H_R
Bit 18 - When this bit is 1, the H counter does not run and no events can occur. A reset sets this bit. When the HALT_H bit is one, the STOP_H bit is cleared. It is possible to remove the halt condition while keeping the SCT in the stop condition (not running) with a single write to this register to simultaneously clear the HALT bit and set the STOP bit. Once set, this bit can only be cleared by software to restore counter operation. This bit is set on reset.
sourcepub fn clrctr_h(&self) -> CLRCTR_H_R
pub fn clrctr_h(&self) -> CLRCTR_H_R
Bit 19 - Writing a 1 to this bit clears the H counter. This bit always reads as 0.
sourcepub fn pre_h(&self) -> PRE_H_R
pub fn pre_h(&self) -> PRE_H_R
Bits 21:28 - Specifies the factor by which the SCT clock is prescaled to produce the H counter clock. The counter clock is clocked at the rate of the SCT clock divided by PRELH+1. Clear the counter (by writing a 1 to the CLRCTR bit) whenever changing the PRE value.