Struct lpc55_pac::usbphy::ctrl::R

pub struct R(_);

Register CTRL reader

Implementations

impl R

pub fn enhostdiscondetect(&self) -> ENHOSTDISCONDETECT_R

Bit 1 - For host mode, enables high-speed disconnect detector

pub fn enirqhostdiscon(&self) -> ENIRQHOSTDISCON_R

Bit 2 - Enable IRQ for Host disconnect: Enables interrupt for detection of disconnection to Device when in high-speed host mode

pub fn hostdiscondetect_irq(&self) -> HOSTDISCONDETECT_IRQ_R

Bit 3 - Indicates that the device has disconnected in High-Speed mode

pub fn endevplugindet(&self) -> ENDEVPLUGINDET_R

Bit 4 - Enables non-standard resistive plugged-in detection This bit field controls connection of nominal 200kohm resistors to both the USB_DP and USB_DM pins as one method of detecting when a USB cable is attached in device mode

pub fn devplugin_polarity(&self) -> DEVPLUGIN_POLARITY_R

Bit 5 - Device plugin polarity: For device mode, if this bit is cleared to 0, then it trips the interrupt if the device is plugged in

pub fn resumeirqsticky(&self) -> RESUMEIRQSTICKY_R

Bit 8 - Resume IRQ: Set to 1 will make RESUME_IRQ bit a sticky bit until software clear it

pub fn enirqresumedetect(&self) -> ENIRQRESUMEDETECT_R

Bit 9 - Enable IRQ Resume detect: Enables interrupt for detection of a non-J state on the USB line

pub fn resume_irq(&self) -> RESUME_IRQ_R

Bit 10 - Resume IRQ: Indicates that the host is sending a wake-up after suspend

pub fn devplugin_irq(&self) -> DEVPLUGIN_IRQ_R

Bit 12 - Indicates that the device is connected

pub fn enutmilevel2(&self) -> ENUTMILEVEL2_R

Bit 14 - Enables UTMI+ Level 2 operation for the USB HS PHY

pub fn enutmilevel3(&self) -> ENUTMILEVEL3_R

Bit 15 - Enables UTMI+ Level 3 operation for the USB HS PHY

pub fn enirqwakeup(&self) -> ENIRQWAKEUP_R

Bit 16 - Enable wake-up IRQ: Enables interrupt for the wake-up events.

pub fn wakeup_irq(&self) -> WAKEUP_IRQ_R

Bit 17 - Wake-up IRQ: Indicates that there is a wak-eup event

pub fn autoresume_en(&self) -> AUTORESUME_EN_R

Bit 18 - Enable the auto resume feature, when set, HW will use 32KHz clock to send Resume to respond to the device remote wakeup(for host mode only)

pub fn enautoclr_clkgate(&self) -> ENAUTOCLR_CLKGATE_R

Bit 19 - Enables the feature to auto-clear the CLKGATE bit if there is wakeup event while USB is suspended

pub fn enautoclr_phy_pwd(&self) -> ENAUTOCLR_PHY_PWD_R

Bit 20 - Enables the feature to auto-clear the PWD register bits in PWD if there is wakeup event while USB is suspended

pub fn endpdmchg_wkup(&self) -> ENDPDMCHG_WKUP_R

Bit 21 - Enable DP DM change wake-up: Not for customer use

pub fn envbuschg_wkup(&self) -> ENVBUSCHG_WKUP_R

Bit 23 - Enable VBUS change wake-up: Enables the feature to wake-up USB if VBUS is toggled when USB is suspended

pub fn enautoclr_usbclkgate(&self) -> ENAUTOCLR_USBCLKGATE_R

Bit 25 - Enable auto-clear USB Clock gate: Enables the feature to auto-clear the USB0_CLKGATE/USB1_CLKGATE register bit in HW_DIGCTL_CTRL if there is wake-up event on USB0/USB1 while USB0/USB1 is suspended

pub fn enautoset_usbclks(&self) -> ENAUTOSET_USBCLKS_R

Bit 26 - Enable auto-set of USB clocks: Enables the feature to auto-clear the EN_USB_CLKS register bits in HW_CLKCTRL_PLL1CTRL0/HW_CLKCTRL_P LL1CTRL1 if there is wake-up event on USB0/USB1 while USB0/USB1 is suspended

pub fn host_force_ls_se0(&self) -> HOST_FORCE_LS_SE0_R

Bit 28 - Forces the next FS packet that is transmitted to have a EOP with low-speed timing

pub fn utmi_suspendm(&self) -> UTMI_SUSPENDM_R

Bit 29 - Used by the PHY to indicate a powered-down state

pub fn clkgate(&self) -> CLKGATE_R

Bit 30 - Gate UTMI Clocks

pub fn sftrst(&self) -> SFTRST_R

Bit 31 - Writing a 1 to this bit will soft-reset the PWD, TX, RX, and CTRL registers

Methods from Deref<Target = R<CTRL_SPEC>>

pub fn bits(&self) -> REG::Ux

Reads raw bits from register.

Trait Implementations

impl Deref for R

type Target = R<CTRL_SPEC>

The resulting type after dereferencing.

fn deref(&self) -> &Self::Target

Dereferences the value.

impl From<R<CTRL_SPEC>> for R

fn from(reader: R<CTRL_SPEC>) -> Self

Performs the conversion.