Struct linuxfb::Framebuffer

pub struct Framebuffer { /* fields omitted */ }

Represents a single framebuffer device

Example usage:

// Instead of hardcoding the path, you could also use `Framebuffer::list()`
// to find paths to available devices.
let fb = linuxfb::Framebuffer::new("/dev/fb0").unwrap();

println!("Size in pixels: {:?}", fb.get_size());

println!("Bytes per pixel: {:?}", fb.get_bytes_per_pixel());

println!("Physical size in mm: {:?}", fb.get_physical_size());

// Map the framebuffer into memory, so we can write to it:
let mut data = fb.map().unwrap();

// Make everything black:
for i in 0..data.len() {
  data[i] = 0;
}

// Make everything white:
for i in 0..data.len() {
  data[i] = 0xFF;
}

Implementations

impl Framebuffer

pub fn list() -> Result<Vec<PathBuf>>

Returns a list of paths to device nodes, which are handled by the "fb" driver.

Relies on /proc/devices to discover the major number of the device, and on the device nodes to exist in /dev.

Example, assuming there is one framebuffer named fb0:

let devices = linuxfb::Framebuffer::list().unwrap();
println!("Devices: {:?}", devices);
// prints:
//   Devices: ["/dev/fb0"]

pub fn new(path: impl AsRef<Path>) -> Result<Framebuffer, Error>

Attempts to open the framebuffer device at the given path, and query it's properties.

This operation can fail for one of these reasons:

• The device cannot be opened. In this case the error has ErrorKind::Io, and error.io is set. This can happen for example when given a path to a file that does not exist, or when the user lacks permission to open the device.
• Any of the ioctl calls querying device properties fails. In this case the error has ErrorKind::Fb, and error.fb is set. Use error.fb.errno and error.fb.message to find out what failed. This can happen for example when the given path does not refer to a framebuffer device, or when the driver encounters an error.

pub fn map(&self) -> Result<MmapMut, Error>

Maps the framebuffer device into memory.

Returns a memory mapped region, which can be used to modify screen contents.

The size of the region is chosen based on the current virtual size of the display, and the bytes per pixel. Therefore this method should be called after configuring the device.

Since the returned memmap::MmapMut object implements the Drop trait, the region is automatically unmapped, when the returned map goes out of scope.

Note that changes to the data directly appear on screen, so you will most likely see flicker, if you write to a visible region.

To avoid this, you can set the virtual size to be twice as large as the actual size of the display, then only draw to the part of that region that's currently not shown. Once done drawing, use set_offset to make the drawn region appear on screen.

See the double module for a convenient wrapper that does exactly that.

pub fn get_bytes_per_pixel(&self) -> u32

Returns the number of bytes used to represent one pixel.

This can be used to narrow down the format.

pub fn set_bytes_per_pixel(&mut self, value: u32) -> Result<(), Error>

Sets the number of bytes per pixel.

This modifies the bits_per_pixel attribute of the underlying device. The actual consequence of this action depends on the driver.

For at least some drivers, setting a different number of pixels changes the color mode.

Make sure to use get_bytes_per_pixel afterwards to check if the value was changed.

Also use get_pixel_layout, to find out more about the format being used.

This operation fails, when any of the underlying ioctl calls fail. After a failure, the device may be in an undefined state.

pub fn get_pixel_layout(&self) -> PixelLayout

Returns the pixel layout, as reported by the driver.

This value may change, after calling set_bytes_per_pixel.

Some examples:

16-bit, RGB565, meaning rrrrrggggggrrrrr, with LSB right, aka HighColor:

PixelLayout {
  red: PixelLayoutChannel { offset: 11, length: 5, msb_right: false },
  green: PixelLayoutChannel { offset: 5, length: 6, msb_right: false },
  blue: PixelLayoutChannel { offset: 0, length: 5, msb_right: false },
  alpha: PixelLayoutChannel { offset: 0, length: 0, msb_right: false },
};

32-bit, ABGR, meaning aaaaaaaabbbbbbbbbggggggggrrrrrrrr, with LSB right:

PixelLayout {
  red: PixelLayoutChannel { offset: 0, length: 8, msb_right: false },
  green: PixelLayoutChannel { offset: 8, length: 8, msb_right: false },
  blue: PixelLayoutChannel { offset: 16, length: 8, msb_right: false },
  alpha: PixelLayoutChannel { offset: 24, length: 8, msb_right: false },
};

32-bit, RGBA, meaning: rrrrrrrrggggggggbbbbbbbbaaaaaaaa, with LSB right:

PixelLayout {
  red: PixelLayoutChannel { offset: 24, length: 8, msb_right: false },
  green: PixelLayoutChannel { offset: 16, length: 8, msb_right: false },
  blue: PixelLayoutChannel { offset: 8, length: 8, msb_right: false },
  alpha: PixelLayoutChannel { offset: 0, length: 8, msb_right: false },
};

Note that on most devices, setting alpha data does not have any effect, even when an alpha channel is specified in the layout.

pub fn get_size(&self) -> (u32, u32)

Returns the size of the display, in pixels.

pub fn get_virtual_size(&self) -> (u32, u32)

Returns the virtual size of the display, in pixels.

See set_virtual_size for details.

pub fn set_virtual_size(&mut self, w: u32, h: u32) -> Result<(), Error>

Sets the virtual size of the display.

The virtual size defines the area where pixel data can be written to. It should always be equal to or larger than the values returned from get_size.

After setting the virtual size, you can use set_offset to control what region of the "virtual display" is actually shown on screen.

This operation fails, when any of the underlying ioctl calls fail. After a failure, the device may be in an undefined state.

pub fn get_offset(&self) -> (u32, u32)

Returns the current xoffset and yoffset of the underlying device.

pub fn set_offset(&mut self, x: u32, y: u32) -> Result<(), Error>

Sets the xoffset and yoffset of the underlying device.

This can be used to pan the display.

This operation fails, when any of the underlying ioctl calls fail. After a failure, the device may be in an undefined state.

pub fn get_physical_size(&self) -> (u32, u32)

Returns the physical size of the device in millimeters, as reported by the driver.

pub fn get_id(&self) -> String

Get identifier string of the device, as reported by the driver.