Crate imxrt_dcd

i.MX RT1060 Device Configuration Data (DCD) Generator

The i.MX RT1050/1060 series of MCUs feature a ROM bootloader. As a part of the boot process, it interprets the Device Configuration Data (DCD) section in the firmware image to perform limited initialization and validation of peripheral registers, e.g. to set up external memory controllers, before any ARM instructions from the firmware image is run.

This crate allows you to generate a DCD binary (byte array) from its semantic description. This is useful e.g. in a build.rs script to generate a static variable to be linked to the firmware image. (Shameless plug: See static-include-bytes.)

What does the DCD do exactly?

Reference: i.MX RT1060 Reference Manual (rev. 3), §9.7.2 .

The DCD section in the firmware image is a serialized byte array of one or more commands:

• Write: Write value (1/2/4-byte) to address.

  • *address = value — direct write
  • *address &= !value — read-modify-write clear bits
  • *address |= value — read-modify-write set bits

• Check: Read from address until the value satisfies the condition or too many attempts.

  • (*address & mask) == 0 — all clear
  • (*address & mask) == mask — all set
  • (*address & mask) != mask — any clear
  • (*address & mask) != 0 — any set

• NOP: Ignored (might act as a delay?)

Write command compression

Multiple Write commands with the same bit width and operation (i.e. write/clear/set) can be merged (sharing the same command header) to save some bytes. This might be helpful as there is a hardcoded byte length limit in the ROM (1768 bytes for RT1060, including headers).

This crate automatically performs this compression but does not enforce any byte size limit.

Valid Write command address ranges

The ROM only allows Write commands to a limited number of address ranges:

Begin	End (inclusive)	Description
0x400A_4000	0x400A_7FFF	IOMUX Control SNVS GPR
0x400A_8000	0x400A_BFFF	IOMUX Control SNVS
0x400A_C000	0x400A_FFFF	IOMUX Control GPR
0x401F_8000	0x401F_BFFF	IOMUX Control
0x400D_8000	0x400D_BFFF	CCM Analog
0x400F_C000	0x400F_FFFF	CCM
0x402F_0000	0x402F_3FFF	SEMC

Writing to anywhere outside these ranges will cause the ROM to immediately abandon interpreting the rest of your DCD.

Again, this crate does not enforce any address range limitations.

Check command polling count

The Check command may specify one of the following:

• Omitted max polling count: ROM will poll indefinitely as long as the condition remains unsatisfied.
• max polling count == 0: Equivalent to NOP.
• max polling count > 0: If the max polling count is hit, the ROM will immediately abandon interpreting the rest of your DCD.

Note that the ROM does not seem to limit the address range of Check commands.

Toy Example

use imxrt_dcd::*;

let mut buf = std::io::Cursor::new(vec![]);
let byte_len = serialize(
    &mut buf,
    &[
        Command::Nop,
        Command::Write(Write {
            width: Width::B4,
            op: WriteOp::Write,
            address: 0x01234567,
            value: 0xdeadbeef,
        }),
        Command::Check(Check {
            width: Width::B2,
            cond: CheckCond::AnySet,
            address: 0x89abcdef,
            mask: 0x55aa55aa,
            count: Some(16),
        }),
        Command::Check(Check {
            width: Width::B1,
            cond: CheckCond::AnyClear,
            address: 0x89abcdef,
            mask: 0x55aa55aa,
            count: None,
        }),
    ],
)
.expect("IO failure");
assert_eq!(byte_len, 48);
assert_eq!(
    &buf.get_ref()[0..48],
    &[
        // DCD header
        0xD2, 0, 48, 0x41,
        // nop
        0xC0, 0x00, 0x04, 0x00,
        // write
        0xCC, 0, 12, 0x04, 0x01, 0x23, 0x45, 0x67, 0xde, 0xad, 0xbe, 0xef,
        // check with count
        0xCF, 0, 16, 0x1a, 0x89, 0xab, 0xcd, 0xef, 0x55, 0xaa, 0x55, 0xaa, 0, 0, 0, 16,
        // check without
        0xCF, 0, 12, 0x09, 0x89, 0xab, 0xcd, 0xef, 0x55, 0xaa, 0x55, 0xaa,
    ]
);

Structs

• Check
  Command for polling an address until the value matches a given bitmask condition.
• Write
  Command for writing a value to an address.

Enums

• CheckCond
  Check condition variant.
• Command
  A DCD command.
• Width
  Byte width of the bus read/write.
• WriteOp
  Write operation variant.

Functions

• serialize
  Serializes given commands as a complete DCD block into a byte stream. Consecutive write commands with the same width and op are automatically combined.