Module ctrl

configure apb saradc controller

Structs

CTRL_SPEC

configure apb saradc controller

Type Aliases

DATA_SAR_SEL_R

Field DATA_SAR_SEL reader - 1: sar_sel will be coded by the MSB of the 16-bit output data, in this case the resolution should not be larger than 11 bits.

DATA_SAR_SEL_W

Field DATA_SAR_SEL writer - 1: sar_sel will be coded by the MSB of the 16-bit output data, in this case the resolution should not be larger than 11 bits.

DATA_TO_I2S_R

Field DATA_TO_I2S reader - 1: I2S input data is from SAR ADC (for DMA), 0: I2S input data is from GPIO matrix

DATA_TO_I2S_W

Field DATA_TO_I2S writer - 1: I2S input data is from SAR ADC (for DMA), 0: I2S input data is from GPIO matrix

R

Register CTRL reader

SAR1_PATT_LEN_R

Field SAR1_PATT_LEN reader - 0 ~ 15 means length 1 ~ 16

SAR1_PATT_LEN_W

Field SAR1_PATT_LEN writer - 0 ~ 15 means length 1 ~ 16

SAR1_PATT_P_CLEAR_R

Field SAR1_PATT_P_CLEAR reader - clear the pointer of pattern table for DIG ADC1 CTRL

SAR1_PATT_P_CLEAR_W

Field SAR1_PATT_P_CLEAR writer - clear the pointer of pattern table for DIG ADC1 CTRL

SAR2_PATT_LEN_R

Field SAR2_PATT_LEN reader - 0 ~ 15 means length 1 ~ 16

SAR2_PATT_LEN_W

Field SAR2_PATT_LEN writer - 0 ~ 15 means length 1 ~ 16

SAR2_PATT_P_CLEAR_R

Field SAR2_PATT_P_CLEAR reader - clear the pointer of pattern table for DIG ADC2 CTRL

SAR2_PATT_P_CLEAR_W

Field SAR2_PATT_P_CLEAR writer - clear the pointer of pattern table for DIG ADC2 CTRL

SAR_CLK_DIV_R

Field SAR_CLK_DIV reader - SAR clock divider

SAR_CLK_DIV_W

Field SAR_CLK_DIV writer - SAR clock divider

SAR_CLK_GATED_R

Field SAR_CLK_GATED reader - enable SAR CLK gate when saradc idle

SAR_CLK_GATED_W

Field SAR_CLK_GATED writer - enable SAR CLK gate when saradc idle

SAR_SEL_R

Field SAR_SEL reader - 0: SAR1, 1: SAR2, only work for single SAR mode

SAR_SEL_W

Field SAR_SEL writer - 0: SAR1, 1: SAR2, only work for single SAR mode

START_FORCE_R

Field START_FORCE reader - enable start saradc by sw

START_FORCE_W

Field START_FORCE writer - enable start saradc by sw

START_R

Field START reader - start saradc by sw

START_W

Field START writer - start saradc by sw

W

Register CTRL writer

WAIT_ARB_CYCLE_R

Field WAIT_ARB_CYCLE reader - wait arbit signal stable after sar_done

WAIT_ARB_CYCLE_W

Field WAIT_ARB_CYCLE writer - wait arbit signal stable after sar_done

WORK_MODE_R

Field WORK_MODE reader - 0: single mode, 1: double mode, 2: alternate mode

WORK_MODE_W

Field WORK_MODE writer - 0: single mode, 1: double mode, 2: alternate mode

XPD_SAR_FORCE_R

Field XPD_SAR_FORCE reader - force option to xpd sar blocks

XPD_SAR_FORCE_W

Field XPD_SAR_FORCE writer - force option to xpd sar blocks