Module conf0

Configuration register 0 for unit

Re-exports

pub use CH_NEG_MODE_R as CH_POS_MODE_R;

pub use CH_NEG_MODE_W as CH_POS_MODE_W;

pub use CH_HCTRL_MODE_R as CH_LCTRL_MODE_R;

pub use CH_HCTRL_MODE_W as CH_LCTRL_MODE_W;

Structs

CONF0_SPEC

Configuration register 0 for unit

Enums

CTRL_MODE

Configures how the CHn_POS_MODE/CHn_NEG_MODE settings will be modified when the control signal is high.

EDGE_MODE

Configures the behavior when the signal input of channel %s detects a negative edge.

Type Aliases

CH_HCTRL_MODE_R

Field CH_HCTRL_MODE(0-1) reader - Configures how the CHn_POS_MODE/CHn_NEG_MODE settings will be modified when the control signal is high.

CH_HCTRL_MODE_W

Field CH_HCTRL_MODE(0-1) writer - Configures how the CHn_POS_MODE/CHn_NEG_MODE settings will be modified when the control signal is high.

CH_NEG_MODE_R

Field CH_NEG_MODE(0-1) reader - Configures the behavior when the signal input of channel %s detects a negative edge.

CH_NEG_MODE_W

Field CH_NEG_MODE(0-1) writer - Configures the behavior when the signal input of channel %s detects a negative edge.

FILTER_EN_R

Field FILTER_EN reader - This is the enable bit for unit %s’s input filter.

FILTER_EN_W

Field FILTER_EN writer - This is the enable bit for unit %s’s input filter.

FILTER_THRES_R

Field FILTER_THRES reader - This sets the maximum threshold, in APB_CLK cycles, for the filter. Any pulses with width less than this will be ignored when the filter is enabled.

FILTER_THRES_W

Field FILTER_THRES writer - This sets the maximum threshold, in APB_CLK cycles, for the filter. Any pulses with width less than this will be ignored when the filter is enabled.

R

Register CONF0 reader

THR_H_LIM_EN_R

Field THR_H_LIM_EN reader - This is the enable bit for unit %s’s thr_h_lim comparator. Configures it to enable the high limit interrupt.

THR_H_LIM_EN_W

Field THR_H_LIM_EN writer - This is the enable bit for unit %s’s thr_h_lim comparator. Configures it to enable the high limit interrupt.

THR_L_LIM_EN_R

Field THR_L_LIM_EN reader - This is the enable bit for unit %s’s thr_l_lim comparator. Configures it to enable the low limit interrupt.

THR_L_LIM_EN_W

Field THR_L_LIM_EN writer - This is the enable bit for unit %s’s thr_l_lim comparator. Configures it to enable the low limit interrupt.

THR_THRES0_EN_R

Field THR_THRES0_EN reader - This is the enable bit for unit %s’s thres0 comparator.

THR_THRES0_EN_W

Field THR_THRES0_EN writer - This is the enable bit for unit %s’s thres0 comparator.

THR_THRES1_EN_R

Field THR_THRES1_EN reader - This is the enable bit for unit %s’s thres1 comparator.

THR_THRES1_EN_W

Field THR_THRES1_EN writer - This is the enable bit for unit %s’s thres1 comparator.

THR_ZERO_EN_R

Field THR_ZERO_EN reader - This is the enable bit for unit %s’s zero comparator.

THR_ZERO_EN_W

Field THR_ZERO_EN writer - This is the enable bit for unit %s’s zero comparator.

W

Register CONF0 writer