Module user

SPI USER control register

Structs

USER_SPEC

SPI USER control register

Type Aliases

CK_OUT_EDGE_R

Field CK_OUT_EDGE reader - the bit combined with spi_mosi_delay_mode bits to set mosi signal delay mode. Can be configured in CONF state.

CK_OUT_EDGE_W

Field CK_OUT_EDGE writer - the bit combined with spi_mosi_delay_mode bits to set mosi signal delay mode. Can be configured in CONF state.

CS_HOLD_R

Field CS_HOLD reader - spi cs keep low when spi is in done phase. 1: enable 0: disable. Can be configured in CONF state.

CS_HOLD_W

Field CS_HOLD writer - spi cs keep low when spi is in done phase. 1: enable 0: disable. Can be configured in CONF state.

CS_SETUP_R

Field CS_SETUP reader - spi cs is enable when spi is in prepare phase. 1: enable 0: disable. Can be configured in CONF state.

CS_SETUP_W

Field CS_SETUP writer - spi cs is enable when spi is in prepare phase. 1: enable 0: disable. Can be configured in CONF state.

DOUTDIN_R

Field DOUTDIN reader - Set the bit to enable full duplex communication. 1: enable 0: disable. Can be configured in CONF state.

DOUTDIN_W

Field DOUTDIN writer - Set the bit to enable full duplex communication. 1: enable 0: disable. Can be configured in CONF state.

FWRITE_DUAL_R

Field FWRITE_DUAL reader - In the write operations read-data phase apply 2 signals. Can be configured in CONF state.

FWRITE_DUAL_W

Field FWRITE_DUAL writer - In the write operations read-data phase apply 2 signals. Can be configured in CONF state.

FWRITE_OCT_R

Field FWRITE_OCT reader - In the write operations read-data phase apply 8 signals. Can be configured in CONF state.

FWRITE_QUAD_R

Field FWRITE_QUAD reader - In the write operations read-data phase apply 4 signals. Can be configured in CONF state.

FWRITE_QUAD_W

Field FWRITE_QUAD writer - In the write operations read-data phase apply 4 signals. Can be configured in CONF state.

OPI_MODE_R

Field OPI_MODE reader - Just for master mode. 1: spi controller is in OPI mode (all in 8-b-m). 0: others. Can be configured in CONF state.

QPI_MODE_R

Field QPI_MODE reader - Both for master mode and slave mode. 1: spi controller is in QPI mode. 0: others. Can be configured in CONF state.

QPI_MODE_W

Field QPI_MODE writer - Both for master mode and slave mode. 1: spi controller is in QPI mode. 0: others. Can be configured in CONF state.

R

Register USER reader

RSCK_I_EDGE_R

Field RSCK_I_EDGE reader - In the slave mode, this bit can be used to change the polarity of rsck. 0: rsck = !spi_ck_i. 1:rsck = spi_ck_i.

RSCK_I_EDGE_W

Field RSCK_I_EDGE writer - In the slave mode, this bit can be used to change the polarity of rsck. 0: rsck = !spi_ck_i. 1:rsck = spi_ck_i.

SIO_R

Field SIO reader - Set the bit to enable 3-line half duplex communication mosi and miso signals share the same pin. 1: enable 0: disable. Can be configured in CONF state.

SIO_W

Field SIO writer - Set the bit to enable 3-line half duplex communication mosi and miso signals share the same pin. 1: enable 0: disable. Can be configured in CONF state.

TSCK_I_EDGE_R

Field TSCK_I_EDGE reader - In the slave mode, this bit can be used to change the polarity of tsck. 0: tsck = spi_ck_i. 1:tsck = !spi_ck_i.

TSCK_I_EDGE_W

Field TSCK_I_EDGE writer - In the slave mode, this bit can be used to change the polarity of tsck. 0: tsck = spi_ck_i. 1:tsck = !spi_ck_i.

USR_ADDR_R

Field USR_ADDR reader - This bit enable the address phase of an operation. Can be configured in CONF state.

USR_ADDR_W

Field USR_ADDR writer - This bit enable the address phase of an operation. Can be configured in CONF state.

USR_COMMAND_R

Field USR_COMMAND reader - This bit enable the command phase of an operation. Can be configured in CONF state.

USR_COMMAND_W

Field USR_COMMAND writer - This bit enable the command phase of an operation. Can be configured in CONF state.

USR_CONF_NXT_R

Field USR_CONF_NXT reader - 1: Enable the DMA CONF phase of next seg-trans operation, which means seg-trans will continue. 0: The seg-trans will end after the current SPI seg-trans or this is not seg-trans mode. Can be configured in CONF state.

USR_CONF_NXT_W

Field USR_CONF_NXT writer - 1: Enable the DMA CONF phase of next seg-trans operation, which means seg-trans will continue. 0: The seg-trans will end after the current SPI seg-trans or this is not seg-trans mode. Can be configured in CONF state.

USR_DUMMY_IDLE_R

Field USR_DUMMY_IDLE reader - spi clock is disable in dummy phase when the bit is enable. Can be configured in CONF state.

USR_DUMMY_IDLE_W

Field USR_DUMMY_IDLE writer - spi clock is disable in dummy phase when the bit is enable. Can be configured in CONF state.

USR_DUMMY_R

Field USR_DUMMY reader - This bit enable the dummy phase of an operation. Can be configured in CONF state.

USR_DUMMY_W

Field USR_DUMMY writer - This bit enable the dummy phase of an operation. Can be configured in CONF state.

USR_MISO_HIGHPART_R

Field USR_MISO_HIGHPART reader - read-data phase only access to high-part of the buffer spi_w8~spi_w15. 1: enable 0: disable. Can be configured in CONF state.

USR_MISO_HIGHPART_W

Field USR_MISO_HIGHPART writer - read-data phase only access to high-part of the buffer spi_w8~spi_w15. 1: enable 0: disable. Can be configured in CONF state.

USR_MISO_R

Field USR_MISO reader - This bit enable the read-data phase of an operation. Can be configured in CONF state.

USR_MISO_W

Field USR_MISO writer - This bit enable the read-data phase of an operation. Can be configured in CONF state.

USR_MOSI_HIGHPART_R

Field USR_MOSI_HIGHPART reader - write-data phase only access to high-part of the buffer spi_w8~spi_w15. 1: enable 0: disable. Can be configured in CONF state.

USR_MOSI_HIGHPART_W

Field USR_MOSI_HIGHPART writer - write-data phase only access to high-part of the buffer spi_w8~spi_w15. 1: enable 0: disable. Can be configured in CONF state.

USR_MOSI_R

Field USR_MOSI reader - This bit enable the write-data phase of an operation. Can be configured in CONF state.

USR_MOSI_W

Field USR_MOSI writer - This bit enable the write-data phase of an operation. Can be configured in CONF state.

W

Register USER writer