#[doc = r"Register block"]
#[repr(C)]
#[cfg_attr(feature = "impl-register-debug", derive(Debug))]
pub struct RegisterBlock {
    scl_low_period: SCL_LOW_PERIOD,
    ctr: CTR,
    sr: SR,
    to: TO,
    _reserved4: [u8; 0x04],
    fifo_st: FIFO_ST,
    fifo_conf: FIFO_CONF,
    data: DATA,
    int_raw: INT_RAW,
    int_clr: INT_CLR,
    int_ena: INT_ENA,
    int_status: INT_STATUS,
    sda_hold: SDA_HOLD,
    sda_sample: SDA_SAMPLE,
    scl_high_period: SCL_HIGH_PERIOD,
    _reserved14: [u8; 0x04],
    scl_start_hold: SCL_START_HOLD,
    scl_rstart_setup: SCL_RSTART_SETUP,
    scl_stop_hold: SCL_STOP_HOLD,
    scl_stop_setup: SCL_STOP_SETUP,
    filter_cfg: FILTER_CFG,
    clk_conf: CLK_CONF,
    comd0: COMD0,
    comd1: COMD1,
    comd2: COMD2,
    comd3: COMD3,
    comd4: COMD4,
    comd5: COMD5,
    comd6: COMD6,
    comd7: COMD7,
    scl_st_time_out: SCL_ST_TIME_OUT,
    scl_main_st_time_out: SCL_MAIN_ST_TIME_OUT,
    scl_sp_conf: SCL_SP_CONF,
    _reserved31: [u8; 0x74],
    date: DATE,
    _reserved32: [u8; 0x04],
    txfifo_start_addr: TXFIFO_START_ADDR,
    _reserved33: [u8; 0x7c],
    rxfifo_start_addr: RXFIFO_START_ADDR,
}
impl RegisterBlock {
    #[doc = "0x00 - Configures the low level width of the SCL Clock"]
    #[inline(always)]
    pub const fn scl_low_period(&self) -> &SCL_LOW_PERIOD {
        &self.scl_low_period
    }
    #[doc = "0x04 - Transmission setting"]
    #[inline(always)]
    pub const fn ctr(&self) -> &CTR {
        &self.ctr
    }
    #[doc = "0x08 - Describe I2C work status."]
    #[inline(always)]
    pub const fn sr(&self) -> &SR {
        &self.sr
    }
    #[doc = "0x0c - Setting time out control for receiving data."]
    #[inline(always)]
    pub const fn to(&self) -> &TO {
        &self.to
    }
    #[doc = "0x14 - FIFO status register."]
    #[inline(always)]
    pub const fn fifo_st(&self) -> &FIFO_ST {
        &self.fifo_st
    }
    #[doc = "0x18 - FIFO configuration register."]
    #[inline(always)]
    pub const fn fifo_conf(&self) -> &FIFO_CONF {
        &self.fifo_conf
    }
    #[doc = "0x1c - Rx FIFO read data."]
    #[inline(always)]
    pub const fn data(&self) -> &DATA {
        &self.data
    }
    #[doc = "0x20 - Raw interrupt status"]
    #[inline(always)]
    pub const fn int_raw(&self) -> &INT_RAW {
        &self.int_raw
    }
    #[doc = "0x24 - Interrupt clear bits"]
    #[inline(always)]
    pub const fn int_clr(&self) -> &INT_CLR {
        &self.int_clr
    }
    #[doc = "0x28 - Interrupt enable bits"]
    #[inline(always)]
    pub const fn int_ena(&self) -> &INT_ENA {
        &self.int_ena
    }
    #[doc = "0x2c - Status of captured I2C communication events"]
    #[inline(always)]
    pub const fn int_status(&self) -> &INT_STATUS {
        &self.int_status
    }
    #[doc = "0x30 - Configures the hold time after a negative SCL edge."]
    #[inline(always)]
    pub const fn sda_hold(&self) -> &SDA_HOLD {
        &self.sda_hold
    }
    #[doc = "0x34 - Configures the sample time after a positive SCL edge."]
    #[inline(always)]
    pub const fn sda_sample(&self) -> &SDA_SAMPLE {
        &self.sda_sample
    }
    #[doc = "0x38 - Configures the high level width of SCL"]
    #[inline(always)]
    pub const fn scl_high_period(&self) -> &SCL_HIGH_PERIOD {
        &self.scl_high_period
    }
    #[doc = "0x40 - Configures the delay between the SDA and SCL negative edge for a start condition"]
    #[inline(always)]
    pub const fn scl_start_hold(&self) -> &SCL_START_HOLD {
        &self.scl_start_hold
    }
    #[doc = "0x44 - Configures the delay between the positive edge of SCL and the negative edge of SDA"]
    #[inline(always)]
    pub const fn scl_rstart_setup(&self) -> &SCL_RSTART_SETUP {
        &self.scl_rstart_setup
    }
    #[doc = "0x48 - Configures the delay after the SCL clock edge for a stop condition"]
    #[inline(always)]
    pub const fn scl_stop_hold(&self) -> &SCL_STOP_HOLD {
        &self.scl_stop_hold
    }
    #[doc = "0x4c - Configures the delay between the SDA and SCL positive edge for a stop condition"]
    #[inline(always)]
    pub const fn scl_stop_setup(&self) -> &SCL_STOP_SETUP {
        &self.scl_stop_setup
    }
    #[doc = "0x50 - SCL and SDA filter configuration register"]
    #[inline(always)]
    pub const fn filter_cfg(&self) -> &FILTER_CFG {
        &self.filter_cfg
    }
    #[doc = "0x54 - I2C CLK configuration register"]
    #[inline(always)]
    pub const fn clk_conf(&self) -> &CLK_CONF {
        &self.clk_conf
    }
    #[doc = "0x58 - I2C command register 0"]
    #[inline(always)]
    pub const fn comd0(&self) -> &COMD0 {
        &self.comd0
    }
    #[doc = "0x5c - I2C command register 1"]
    #[inline(always)]
    pub const fn comd1(&self) -> &COMD1 {
        &self.comd1
    }
    #[doc = "0x60 - I2C command register 2"]
    #[inline(always)]
    pub const fn comd2(&self) -> &COMD2 {
        &self.comd2
    }
    #[doc = "0x64 - I2C command register 3"]
    #[inline(always)]
    pub const fn comd3(&self) -> &COMD3 {
        &self.comd3
    }
    #[doc = "0x68 - I2C command register 4"]
    #[inline(always)]
    pub const fn comd4(&self) -> &COMD4 {
        &self.comd4
    }
    #[doc = "0x6c - I2C command register 5"]
    #[inline(always)]
    pub const fn comd5(&self) -> &COMD5 {
        &self.comd5
    }
    #[doc = "0x70 - I2C command register 6"]
    #[inline(always)]
    pub const fn comd6(&self) -> &COMD6 {
        &self.comd6
    }
    #[doc = "0x74 - I2C command register 7"]
    #[inline(always)]
    pub const fn comd7(&self) -> &COMD7 {
        &self.comd7
    }
    #[doc = "0x78 - SCL status time out register"]
    #[inline(always)]
    pub const fn scl_st_time_out(&self) -> &SCL_ST_TIME_OUT {
        &self.scl_st_time_out
    }
    #[doc = "0x7c - SCL main status time out register"]
    #[inline(always)]
    pub const fn scl_main_st_time_out(&self) -> &SCL_MAIN_ST_TIME_OUT {
        &self.scl_main_st_time_out
    }
    #[doc = "0x80 - Power configuration register"]
    #[inline(always)]
    pub const fn scl_sp_conf(&self) -> &SCL_SP_CONF {
        &self.scl_sp_conf
    }
    #[doc = "0xf8 - Version register"]
    #[inline(always)]
    pub const fn date(&self) -> &DATE {
        &self.date
    }
    #[doc = "0x100 - I2C TXFIFO base address register"]
    #[inline(always)]
    pub const fn txfifo_start_addr(&self) -> &TXFIFO_START_ADDR {
        &self.txfifo_start_addr
    }
    #[doc = "0x180 - I2C RXFIFO base address register"]
    #[inline(always)]
    pub const fn rxfifo_start_addr(&self) -> &RXFIFO_START_ADDR {
        &self.rxfifo_start_addr
    }
}
#[doc = "SCL_LOW_PERIOD (rw) register accessor: Configures the low level width of the SCL Clock\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`scl_low_period::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`scl_low_period::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@scl_low_period`] module"]
pub type SCL_LOW_PERIOD = crate::Reg<scl_low_period::SCL_LOW_PERIOD_SPEC>;
#[doc = "Configures the low level width of the SCL Clock"]
pub mod scl_low_period;
#[doc = "CTR (rw) register accessor: Transmission setting\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`ctr::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`ctr::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@ctr`] module"]
pub type CTR = crate::Reg<ctr::CTR_SPEC>;
#[doc = "Transmission setting"]
pub mod ctr;
#[doc = "SR (r) register accessor: Describe I2C work status.\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`sr::R`].  See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@sr`] module"]
pub type SR = crate::Reg<sr::SR_SPEC>;
#[doc = "Describe I2C work status."]
pub mod sr;
#[doc = "TO (rw) register accessor: Setting time out control for receiving data.\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`to::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`to::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@to`] module"]
pub type TO = crate::Reg<to::TO_SPEC>;
#[doc = "Setting time out control for receiving data."]
pub mod to;
#[doc = "FIFO_ST (r) register accessor: FIFO status register.\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`fifo_st::R`].  See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@fifo_st`] module"]
pub type FIFO_ST = crate::Reg<fifo_st::FIFO_ST_SPEC>;
#[doc = "FIFO status register."]
pub mod fifo_st;
#[doc = "FIFO_CONF (rw) register accessor: FIFO configuration register.\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`fifo_conf::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`fifo_conf::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@fifo_conf`] module"]
pub type FIFO_CONF = crate::Reg<fifo_conf::FIFO_CONF_SPEC>;
#[doc = "FIFO configuration register."]
pub mod fifo_conf;
#[doc = "DATA (r) register accessor: Rx FIFO read data.\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`data::R`].  See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@data`] module"]
pub type DATA = crate::Reg<data::DATA_SPEC>;
#[doc = "Rx FIFO read data."]
pub mod data;
#[doc = "INT_RAW (r) register accessor: Raw interrupt status\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`int_raw::R`].  See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@int_raw`] module"]
pub type INT_RAW = crate::Reg<int_raw::INT_RAW_SPEC>;
#[doc = "Raw interrupt status"]
pub mod int_raw;
#[doc = "INT_CLR (w) register accessor: Interrupt clear bits\n\nYou can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`int_clr::W`]. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@int_clr`] module"]
pub type INT_CLR = crate::Reg<int_clr::INT_CLR_SPEC>;
#[doc = "Interrupt clear bits"]
pub mod int_clr;
#[doc = "INT_ENA (rw) register accessor: Interrupt enable bits\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`int_ena::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`int_ena::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@int_ena`] module"]
pub type INT_ENA = crate::Reg<int_ena::INT_ENA_SPEC>;
#[doc = "Interrupt enable bits"]
pub mod int_ena;
#[doc = "INT_STATUS (r) register accessor: Status of captured I2C communication events\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`int_status::R`].  See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@int_status`] module"]
pub type INT_STATUS = crate::Reg<int_status::INT_STATUS_SPEC>;
#[doc = "Status of captured I2C communication events"]
pub mod int_status;
#[doc = "SDA_HOLD (rw) register accessor: Configures the hold time after a negative SCL edge.\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`sda_hold::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`sda_hold::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@sda_hold`] module"]
pub type SDA_HOLD = crate::Reg<sda_hold::SDA_HOLD_SPEC>;
#[doc = "Configures the hold time after a negative SCL edge."]
pub mod sda_hold;
#[doc = "SDA_SAMPLE (rw) register accessor: Configures the sample time after a positive SCL edge.\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`sda_sample::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`sda_sample::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@sda_sample`] module"]
pub type SDA_SAMPLE = crate::Reg<sda_sample::SDA_SAMPLE_SPEC>;
#[doc = "Configures the sample time after a positive SCL edge."]
pub mod sda_sample;
#[doc = "SCL_HIGH_PERIOD (rw) register accessor: Configures the high level width of SCL\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`scl_high_period::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`scl_high_period::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@scl_high_period`] module"]
pub type SCL_HIGH_PERIOD = crate::Reg<scl_high_period::SCL_HIGH_PERIOD_SPEC>;
#[doc = "Configures the high level width of SCL"]
pub mod scl_high_period;
#[doc = "SCL_START_HOLD (rw) register accessor: Configures the delay between the SDA and SCL negative edge for a start condition\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`scl_start_hold::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`scl_start_hold::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@scl_start_hold`] module"]
pub type SCL_START_HOLD = crate::Reg<scl_start_hold::SCL_START_HOLD_SPEC>;
#[doc = "Configures the delay between the SDA and SCL negative edge for a start condition"]
pub mod scl_start_hold;
#[doc = "SCL_RSTART_SETUP (rw) register accessor: Configures the delay between the positive edge of SCL and the negative edge of SDA\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`scl_rstart_setup::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`scl_rstart_setup::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@scl_rstart_setup`] module"]
pub type SCL_RSTART_SETUP = crate::Reg<scl_rstart_setup::SCL_RSTART_SETUP_SPEC>;
#[doc = "Configures the delay between the positive edge of SCL and the negative edge of SDA"]
pub mod scl_rstart_setup;
#[doc = "SCL_STOP_HOLD (rw) register accessor: Configures the delay after the SCL clock edge for a stop condition\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`scl_stop_hold::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`scl_stop_hold::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@scl_stop_hold`] module"]
pub type SCL_STOP_HOLD = crate::Reg<scl_stop_hold::SCL_STOP_HOLD_SPEC>;
#[doc = "Configures the delay after the SCL clock edge for a stop condition"]
pub mod scl_stop_hold;
#[doc = "SCL_STOP_SETUP (rw) register accessor: Configures the delay between the SDA and SCL positive edge for a stop condition\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`scl_stop_setup::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`scl_stop_setup::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@scl_stop_setup`] module"]
pub type SCL_STOP_SETUP = crate::Reg<scl_stop_setup::SCL_STOP_SETUP_SPEC>;
#[doc = "Configures the delay between the SDA and SCL positive edge for a stop condition"]
pub mod scl_stop_setup;
#[doc = "FILTER_CFG (rw) register accessor: SCL and SDA filter configuration register\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`filter_cfg::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`filter_cfg::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@filter_cfg`] module"]
pub type FILTER_CFG = crate::Reg<filter_cfg::FILTER_CFG_SPEC>;
#[doc = "SCL and SDA filter configuration register"]
pub mod filter_cfg;
#[doc = "CLK_CONF (rw) register accessor: I2C CLK configuration register\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`clk_conf::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`clk_conf::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@clk_conf`] module"]
pub type CLK_CONF = crate::Reg<clk_conf::CLK_CONF_SPEC>;
#[doc = "I2C CLK configuration register"]
pub mod clk_conf;
#[doc = "COMD0 (rw) register accessor: I2C command register 0\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`comd0::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`comd0::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@comd0`] module"]
pub type COMD0 = crate::Reg<comd0::COMD0_SPEC>;
#[doc = "I2C command register 0"]
pub mod comd0;
#[doc = "COMD1 (rw) register accessor: I2C command register 1\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`comd1::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`comd1::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@comd1`] module"]
pub type COMD1 = crate::Reg<comd1::COMD1_SPEC>;
#[doc = "I2C command register 1"]
pub mod comd1;
#[doc = "COMD2 (rw) register accessor: I2C command register 2\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`comd2::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`comd2::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@comd2`] module"]
pub type COMD2 = crate::Reg<comd2::COMD2_SPEC>;
#[doc = "I2C command register 2"]
pub mod comd2;
#[doc = "COMD3 (rw) register accessor: I2C command register 3\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`comd3::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`comd3::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@comd3`] module"]
pub type COMD3 = crate::Reg<comd3::COMD3_SPEC>;
#[doc = "I2C command register 3"]
pub mod comd3;
#[doc = "COMD4 (rw) register accessor: I2C command register 4\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`comd4::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`comd4::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@comd4`] module"]
pub type COMD4 = crate::Reg<comd4::COMD4_SPEC>;
#[doc = "I2C command register 4"]
pub mod comd4;
#[doc = "COMD5 (rw) register accessor: I2C command register 5\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`comd5::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`comd5::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@comd5`] module"]
pub type COMD5 = crate::Reg<comd5::COMD5_SPEC>;
#[doc = "I2C command register 5"]
pub mod comd5;
#[doc = "COMD6 (rw) register accessor: I2C command register 6\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`comd6::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`comd6::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@comd6`] module"]
pub type COMD6 = crate::Reg<comd6::COMD6_SPEC>;
#[doc = "I2C command register 6"]
pub mod comd6;
#[doc = "COMD7 (rw) register accessor: I2C command register 7\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`comd7::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`comd7::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@comd7`] module"]
pub type COMD7 = crate::Reg<comd7::COMD7_SPEC>;
#[doc = "I2C command register 7"]
pub mod comd7;
#[doc = "SCL_ST_TIME_OUT (rw) register accessor: SCL status time out register\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`scl_st_time_out::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`scl_st_time_out::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@scl_st_time_out`] module"]
pub type SCL_ST_TIME_OUT = crate::Reg<scl_st_time_out::SCL_ST_TIME_OUT_SPEC>;
#[doc = "SCL status time out register"]
pub mod scl_st_time_out;
#[doc = "SCL_MAIN_ST_TIME_OUT (rw) register accessor: SCL main status time out register\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`scl_main_st_time_out::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`scl_main_st_time_out::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@scl_main_st_time_out`] module"]
pub type SCL_MAIN_ST_TIME_OUT = crate::Reg<scl_main_st_time_out::SCL_MAIN_ST_TIME_OUT_SPEC>;
#[doc = "SCL main status time out register"]
pub mod scl_main_st_time_out;
#[doc = "SCL_SP_CONF (rw) register accessor: Power configuration register\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`scl_sp_conf::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`scl_sp_conf::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@scl_sp_conf`] module"]
pub type SCL_SP_CONF = crate::Reg<scl_sp_conf::SCL_SP_CONF_SPEC>;
#[doc = "Power configuration register"]
pub mod scl_sp_conf;
#[doc = "DATE (rw) register accessor: Version register\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`date::R`].  You can [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`write_with_zero`](crate::generic::Reg::write_with_zero) this register using [`date::W`]. You can also [`modify`](crate::generic::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@date`] module"]
pub type DATE = crate::Reg<date::DATE_SPEC>;
#[doc = "Version register"]
pub mod date;
#[doc = "TXFIFO_START_ADDR (r) register accessor: I2C TXFIFO base address register\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`txfifo_start_addr::R`].  See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@txfifo_start_addr`] module"]
pub type TXFIFO_START_ADDR = crate::Reg<txfifo_start_addr::TXFIFO_START_ADDR_SPEC>;
#[doc = "I2C TXFIFO base address register"]
pub mod txfifo_start_addr;
#[doc = "RXFIFO_START_ADDR (r) register accessor: I2C RXFIFO base address register\n\nYou can [`read`](crate::generic::Reg::read) this register and get [`rxfifo_start_addr::R`].  See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@rxfifo_start_addr`] module"]
pub type RXFIFO_START_ADDR = crate::Reg<rxfifo_start_addr::RXFIFO_START_ADDR_SPEC>;
#[doc = "I2C RXFIFO base address register"]
pub mod rxfifo_start_addr;