Struct esp32c3::UART0

pub struct UART0 { /* private fields */ }

UART (Universal Asynchronous Receiver-Transmitter) Controller 0

Implementations

impl UART0

pub const PTR: *const RegisterBlock = {0x60000000 as *const uart0::RegisterBlock}

Pointer to the register block

pub const fn ptr() -> *const RegisterBlock

Return the pointer to the register block

pub unsafe fn steal() -> Self

Steal an instance of this peripheral

Safety

Ensure that the new instance of the peripheral cannot be used in a way that may race with any existing instances, for example by only accessing read-only or write-only registers, or by consuming the original peripheral and using critical sections to coordinate access between multiple new instances.

Additionally, other software such as HALs may rely on only one peripheral instance existing to ensure memory safety; ensure no stolen instances are passed to such software.

Methods from Deref<Target = RegisterBlock>

pub fn fifo(&self) -> &FIFO

0x00 - FIFO data register

pub fn int_raw(&self) -> &INT_RAW

0x04 - Raw interrupt status

pub fn int_st(&self) -> &INT_ST

0x08 - Masked interrupt status

pub fn int_ena(&self) -> &INT_ENA

0x0c - Interrupt enable bits

pub fn int_clr(&self) -> &INT_CLR

0x10 - Interrupt clear bits

pub fn clkdiv(&self) -> &CLKDIV

0x14 - Clock divider configuration

pub fn rx_filt(&self) -> &RX_FILT

0x18 - Rx Filter configuration

pub fn status(&self) -> &STATUS

0x1c - UART status register

pub fn conf0(&self) -> &CONF0

0x20 - a

pub fn conf1(&self) -> &CONF1

0x24 - Configuration register 1

pub fn lowpulse(&self) -> &LOWPULSE

0x28 - Autobaud minimum low pulse duration register

pub fn highpulse(&self) -> &HIGHPULSE

0x2c - Autobaud minimum high pulse duration register

pub fn rxd_cnt(&self) -> &RXD_CNT

0x30 - Autobaud edge change count register

pub fn flow_conf(&self) -> &FLOW_CONF

0x34 - Software flow-control configuration

pub fn sleep_conf(&self) -> &SLEEP_CONF

0x38 - Sleep-mode configuration

pub fn swfc_conf0(&self) -> &SWFC_CONF0

0x3c - Software flow-control character configuration

pub fn swfc_conf1(&self) -> &SWFC_CONF1

0x40 - Software flow-control character configuration

pub fn txbrk_conf(&self) -> &TXBRK_CONF

0x44 - Tx Break character configuration

pub fn idle_conf(&self) -> &IDLE_CONF

0x48 - Frame-end idle configuration

pub fn rs485_conf(&self) -> &RS485_CONF

0x4c - RS485 mode configuration

pub fn at_cmd_precnt(&self) -> &AT_CMD_PRECNT

0x50 - Pre-sequence timing configuration

pub fn at_cmd_postcnt(&self) -> &AT_CMD_POSTCNT

0x54 - Post-sequence timing configuration

pub fn at_cmd_gaptout(&self) -> &AT_CMD_GAPTOUT

0x58 - Timeout configuration

pub fn at_cmd_char(&self) -> &AT_CMD_CHAR

0x5c - AT escape sequence detection configuration

pub fn mem_conf(&self) -> &MEM_CONF

0x60 - UART threshold and allocation configuration

pub fn mem_tx_status(&self) -> &MEM_TX_STATUS

0x64 - Tx-FIFO write and read offset address.

pub fn mem_rx_status(&self) -> &MEM_RX_STATUS

0x68 - Rx-FIFO write and read offset address.

pub fn fsm_status(&self) -> &FSM_STATUS

0x6c - UART transmit and receive status.

pub fn pospulse(&self) -> &POSPULSE

0x70 - Autobaud high pulse register

pub fn negpulse(&self) -> &NEGPULSE

0x74 - Autobaud low pulse register

pub fn clk_conf(&self) -> &CLK_CONF

0x78 - UART core clock configuration

pub fn date(&self) -> &DATE

0x7c - UART Version register

pub fn id(&self) -> &ID

0x80 - UART ID register

Trait Implementations

impl Debug for UART0

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Deref for UART0

type Target = RegisterBlock

The resulting type after dereferencing.

fn deref(&self) -> &Self::Target

Dereferences the value.

impl Send for UART0