Module esp32_hal::pac::uart0::conf0

Structs

CONF0_SPEC

This register you can read, write_with_zero, reset, write, modify. See API.

R

Register CONF0 reader

W

Register CONF0 writer

Type Definitions

BIT_NUM_R

Field BIT_NUM reader - This registe is used to set the length of data: 0:5bits 1:6bits 2:7bits 3:8bits

BIT_NUM_W

Field BIT_NUM writer - This registe is used to set the length of data: 0:5bits 1:6bits 2:7bits 3:8bits

CLK_EN_R

Field CLK_EN reader - 1.force clock on for registers.support clock only when write registers

CLK_EN_W

Field CLK_EN writer - 1.force clock on for registers.support clock only when write registers

CTS_INV_R

Field CTS_INV reader - Set this bit to inverse the level value of uart cts signal.

CTS_INV_W

Field CTS_INV writer - Set this bit to inverse the level value of uart cts signal.

DSR_INV_R

Field DSR_INV reader - Set this bit to inverse the level value of uart dsr signal.

DSR_INV_W

Field DSR_INV writer - Set this bit to inverse the level value of uart dsr signal.

DTR_INV_R

Field DTR_INV reader - Set this bit to inverse the level value of uart dtr signal.

DTR_INV_W

Field DTR_INV writer - Set this bit to inverse the level value of uart dtr signal.

ERR_WR_MASK_R

Field ERR_WR_MASK reader - 1.receiver stops storing data int fifo when data is wrong. 0.receiver stores the data even if the received data is wrong.

ERR_WR_MASK_W

Field ERR_WR_MASK writer - 1.receiver stops storing data int fifo when data is wrong. 0.receiver stores the data even if the received data is wrong.

IRDA_DPLX_R

Field IRDA_DPLX reader - Set this bit to enable irda loopback mode.

IRDA_DPLX_W

Field IRDA_DPLX writer - Set this bit to enable irda loopback mode.

IRDA_EN_R

Field IRDA_EN reader - Set this bit to enable irda protocol.

IRDA_EN_W

Field IRDA_EN writer - Set this bit to enable irda protocol.

IRDA_RX_INV_R

Field IRDA_RX_INV reader - Set this bit to inverse the level value of irda receiver’s level.

IRDA_RX_INV_W

Field IRDA_RX_INV writer - Set this bit to inverse the level value of irda receiver’s level.

IRDA_TX_EN_R

Field IRDA_TX_EN reader - This is the start enable bit for irda transmitter.

IRDA_TX_EN_W

Field IRDA_TX_EN writer - This is the start enable bit for irda transmitter.

IRDA_TX_INV_R

Field IRDA_TX_INV reader - Set this bit to inverse the level value of irda transmitter’s level.

IRDA_TX_INV_W

Field IRDA_TX_INV writer - Set this bit to inverse the level value of irda transmitter’s level.

IRDA_WCTL_R

Field IRDA_WCTL reader - 1.the irda transmitter’s 11th bit is the same to the 10th bit. 0.set irda transmitter’s 11th bit to 0.

IRDA_WCTL_W

Field IRDA_WCTL writer - 1.the irda transmitter’s 11th bit is the same to the 10th bit. 0.set irda transmitter’s 11th bit to 0.

LOOPBACK_R

Field LOOPBACK reader - Set this bit to enable uart loopback test mode.

LOOPBACK_W

Field LOOPBACK writer - Set this bit to enable uart loopback test mode.

PARITY_EN_R

Field PARITY_EN reader - Set this bit to enable uart parity check.

PARITY_EN_W

Field PARITY_EN writer - Set this bit to enable uart parity check.

PARITY_R

Field PARITY reader - This register is used to configure the parity check mode. 0:even 1:odd

PARITY_W

Field PARITY writer - This register is used to configure the parity check mode. 0:even 1:odd

RTS_INV_R

Field RTS_INV reader - Set this bit to inverse the level value of uart rts signal.

RTS_INV_W

Field RTS_INV writer - Set this bit to inverse the level value of uart rts signal.

RXD_INV_R

Field RXD_INV reader - Set this bit to inverse the level value of uart rxd signal.

RXD_INV_W

Field RXD_INV writer - Set this bit to inverse the level value of uart rxd signal.

RXFIFO_RST_R

Field RXFIFO_RST reader - Set this bit to reset uart receiver’s fifo.

RXFIFO_RST_W

Field RXFIFO_RST writer - Set this bit to reset uart receiver’s fifo.

STOP_BIT_NUM_R

Field STOP_BIT_NUM reader - This register is used to set the length of stop bit. 1:1bit 2:1.5bits 3:2bits

STOP_BIT_NUM_W

Field STOP_BIT_NUM writer - This register is used to set the length of stop bit. 1:1bit 2:1.5bits 3:2bits

SW_DTR_R

Field SW_DTR reader - This register is used to configure the software dtr signal which is used in software flow control..

SW_DTR_W

Field SW_DTR writer - This register is used to configure the software dtr signal which is used in software flow control..

SW_RTS_R

Field SW_RTS reader - This register is used to configure the software rts signal which is used in software flow control.

SW_RTS_W

Field SW_RTS writer - This register is used to configure the software rts signal which is used in software flow control.

TICK_REF_ALWAYS_ON_R

Field TICK_REF_ALWAYS_ON reader - This register is used to select the clock.1.apb clock 0:ref_tick

TICK_REF_ALWAYS_ON_W

Field TICK_REF_ALWAYS_ON writer - This register is used to select the clock.1.apb clock 0:ref_tick

TXD_BRK_R

Field TXD_BRK reader - Set this bit to enbale transmitter to send 0 when the process of sending data is done.

TXD_BRK_W

Field TXD_BRK writer - Set this bit to enbale transmitter to send 0 when the process of sending data is done.

TXD_INV_R

Field TXD_INV reader - Set this bit to inverse the level value of uart txd signal.

TXD_INV_W

Field TXD_INV writer - Set this bit to inverse the level value of uart txd signal.

TXFIFO_RST_R

Field TXFIFO_RST reader - Set this bit to reset uart transmitter’s fifo.

TXFIFO_RST_W

Field TXFIFO_RST writer - Set this bit to reset uart transmitter’s fifo.

TX_FLOW_EN_R

Field TX_FLOW_EN reader - Set this bit to enable transmitter’s flow control function.

TX_FLOW_EN_W

Field TX_FLOW_EN writer - Set this bit to enable transmitter’s flow control function.