Struct stm32g0xx_hal::gpio::gpioa::PA12

pub struct PA12<MODE> { /* private fields */ }

Implementations

impl<MODE> PA12<MODE>

pub fn into_floating_input(self) -> PA12<Input<Floating>>

Configures the pin to operate as a floating input pin

pub fn into_pull_down_input(self) -> PA12<Input<PullDown>>

Configures the pin to operate as a pulled down input pin

pub fn into_pull_up_input(self) -> PA12<Input<PullUp>>

Configures the pin to operate as a pulled up input pin

pub fn into_analog(self) -> PA12<Analog>

Configures the pin to operate as an analog pin

pub fn into_open_drain_output_in_state(
    self,
    initial_state: PinState
) -> PA12<Output<OpenDrain>>

Configures the pin to operate as an open drain output pin with initial_state specifying whether the pin should initially be high or low

pub fn into_open_drain_output(self) -> PA12<Output<OpenDrain>>

Configures the pin to operate as an open drain output pin

pub fn into_push_pull_output_in_state(
    self,
    initial_state: PinState
) -> PA12<Output<PushPull>>

Configures the pin to operate as a push pull output pin with initial_state specifying whether the pin should initially be high or low

pub fn into_push_pull_output(self) -> PA12<Output<PushPull>>

Configures the pin to operate as a push pull output pin

pub fn listen(self, edge: SignalEdge, exti: &mut EXTI) -> PA12<Input<Floating>>

Configures the pin as external trigger

pub fn set_speed(self, speed: Speed) -> Self

Set pin speed

impl<MODE> PA12<Output<MODE>>

pub fn downgrade(self) -> PA<Output<MODE>>

Erases the pin number from the type

This is useful when you want to collect the pins into an array where you need all the elements to have the same type

impl<MODE> PA12<Input<MODE>>

pub fn downgrade(self) -> PA<Input<MODE>>

Erases the pin number from the type

This is useful when you want to collect the pins into an array where you need all the elements to have the same type

Trait Implementations

impl<MODE> DriverEnablePin<USART1> for PA12<MODE>

fn setup(&self)

fn release(self) -> Self

impl<MODE> InputPin for PA12<Input<MODE>>

type Error = Infallible

Error type

fn is_high(&self) -> Result<bool, Self::Error>

Is the input pin high?

fn is_low(&self) -> Result<bool, Self::Error>

Is the input pin low?

impl<MODE> InputPin for PA12<Output<MODE>>

type Error = Infallible

Error type

fn is_high(&self) -> Result<bool, Self::Error>

Is the input pin high?

fn is_low(&self) -> Result<bool, Self::Error>

Is the input pin low?

impl Into<PA12<Input<Floating>>> for PA12<DefaultMode>

fn into(self) -> PA12<Input<Floating>>

Converts this type into the (usually inferred) input type.

impl Into<PA12<Input<PullDown>>> for PA12<DefaultMode>

fn into(self) -> PA12<Input<PullDown>>

Converts this type into the (usually inferred) input type.

impl Into<PA12<Input<PullUp>>> for PA12<DefaultMode>

fn into(self) -> PA12<Input<PullUp>>

Converts this type into the (usually inferred) input type.

impl Into<PA12<Output<OpenDrain>>> for PA12<DefaultMode>

fn into(self) -> PA12<Output<OpenDrain>>

Converts this type into the (usually inferred) input type.

impl Into<PA12<Output<PushPull>>> for PA12<DefaultMode>

fn into(self) -> PA12<Output<PushPull>>

Converts this type into the (usually inferred) input type.

impl OutputPin<COMP2> for PA12<Output<OpenDrain>>

fn setup(&self)

fn release(self) -> Self

impl OutputPin<COMP2> for PA12<Output<PushPull>>

fn setup(&self)

fn release(self) -> Self

impl<MODE> OutputPin for PA12<Output<MODE>>

type Error = Infallible

Error type

fn set_high(&mut self) -> Result<(), Self::Error>

Drives the pin high

fn set_low(&mut self) -> Result<(), Self::Error>

Drives the pin low

fn set_state(&mut self, state: PinState) -> Result<(), Self::Error>

Drives the pin high or low depending on the provided value

impl PinMosi<SPI1> for PA12<DefaultMode>

fn setup(&self)

fn release(self) -> Self

impl SDAPin<I2C2> for PA12<Output<OpenDrain>>

fn setup(&self)

fn release(self) -> Self

impl<MODE> StatefulOutputPin for PA12<Output<MODE>>

fn is_set_high(&self) -> Result<bool, Self::Error>

Is the pin in drive high mode?

fn is_set_low(&self) -> Result<bool, Self::Error>

Is the pin in drive low mode?

impl<MODE> Default for PA12<Output<MODE>>