Struct nrf52833_hal::pac::saadc::RegisterBlock [−][src]
Register block
Fields
tasks_start: Reg<u32, _TASKS_START>
0x00 - Starts the SAADC and prepares the result buffer in RAM
tasks_sample: Reg<u32, _TASKS_SAMPLE>
0x04 - Takes one SAADC sample
tasks_stop: Reg<u32, _TASKS_STOP>
0x08 - Stops the SAADC and terminates all on-going conversions
tasks_calibrateoffset: Reg<u32, _TASKS_CALIBRATEOFFSET>
0x0c - Starts offset auto-calibration
events_started: Reg<u32, _EVENTS_STARTED>
0x100 - The SAADC has started
events_end: Reg<u32, _EVENTS_END>
0x104 - The SAADC has filled up the result buffer
events_done: Reg<u32, _EVENTS_DONE>
0x108 - A conversion task has been completed. Depending on the configuration, multiple conversions might be needed for a result to be transferred to RAM.
events_resultdone: Reg<u32, _EVENTS_RESULTDONE>
0x10c - Result ready for transfer to RAM
events_calibratedone: Reg<u32, _EVENTS_CALIBRATEDONE>
0x110 - Calibration is complete
events_stopped: Reg<u32, _EVENTS_STOPPED>
0x114 - The SAADC has stopped
events_ch: [EVENTS_CH; 8]
0x118 - Peripheral events.
inten: Reg<u32, _INTEN>
0x300 - Enable or disable interrupt
intenset: Reg<u32, _INTENSET>
0x304 - Enable interrupt
intenclr: Reg<u32, _INTENCLR>
0x308 - Disable interrupt
status: Reg<u32, _STATUS>
0x400 - Status
enable: Reg<u32, _ENABLE>
0x500 - Enable or disable SAADC
ch: [CH; 8]
0x510 - Unspecified
resolution: Reg<u32, _RESOLUTION>
0x5f0 - Resolution configuration
oversample: Reg<u32, _OVERSAMPLE>
0x5f4 - Oversampling configuration. The RESOLUTION is applied before averaging, thus for high OVERSAMPLE a higher RESOLUTION should be used.
samplerate: Reg<u32, _SAMPLERATE>
0x5f8 - Controls normal or continuous sample rate
result: RESULT
0x62c - RESULT EasyDMA channel
Auto Trait Implementations
Blanket Implementations
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<T> Borrow<T> for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut<T> for T where
T: ?Sized,
[src]
T: ?Sized,
pub fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> From<T> for T
[src]
impl<T, U> Into<U> for T where
U: From<T>,
[src]
U: From<T>,
impl<Src, Dst> LosslessTryInto<Dst> for Src where
Dst: LosslessTryFrom<Src>,
[src]
Dst: LosslessTryFrom<Src>,
pub fn lossless_try_into(self) -> Option<Dst>
[src]
impl<Src, Dst> LossyInto<Dst> for Src where
Dst: LossyFrom<Src>,
[src]
Dst: LossyFrom<Src>,
pub fn lossy_into(self) -> Dst
[src]
impl<T> Same<T> for T
type Output = T
Should always be Self
impl<T, U> TryFrom<U> for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
pub fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> TryInto<U> for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,