[−][src]Struct imxrt1062_usbnc1::W
Methods
impl<U, REG> W<U, REG>
[src]
impl W<u32, Reg<u32, _USB_OTG1_CTRL>>
[src]
pub fn over_cur_dis(&mut self) -> OVER_CUR_DIS_W
[src]
Bit 7 - Disable OTG1 Overcurrent Detection
pub fn over_cur_pol(&mut self) -> OVER_CUR_POL_W
[src]
Bit 8 - OTG1 Polarity of Overcurrent The polarity of OTG1 port overcurrent event
pub fn pwr_pol(&mut self) -> PWR_POL_W
[src]
Bit 9 - OTG1 Power Polarity This bit should be set according to PMIC Power Pin polarity.
pub fn wie(&mut self) -> WIE_W
[src]
Bit 10 - OTG1 Wake-up Interrupt Enable This bit enables or disables the OTG1 wake-up interrupt
pub fn wkup_sw_en(&mut self) -> WKUP_SW_EN_W
[src]
Bit 14 - OTG1 Software Wake-up Enable
pub fn wkup_sw(&mut self) -> WKUP_SW_W
[src]
Bit 15 - OTG1 Software Wake-up
pub fn wkup_id_en(&mut self) -> WKUP_ID_EN_W
[src]
Bit 16 - OTG1 Wake-up on ID change enable
pub fn wkup_vbus_en(&mut self) -> WKUP_VBUS_EN_W
[src]
Bit 17 - OTG1 wake-up on VBUS change enable
pub fn wkup_dpdm_en(&mut self) -> WKUP_DPDM_EN_W
[src]
Bit 29 - Wake-up on DPDM change enable
impl W<u32, Reg<u32, _USB_OTG1_PHY_CTRL_0>>
[src]
pub fn utmi_clk_vld(&mut self) -> UTMI_CLK_VLD_W
[src]
Bit 31 - Indicating whether OTG1 UTMI PHY clock is valid
Auto Trait Implementations
impl<U, REG> Send for W<U, REG> where
REG: Send,
U: Send,
REG: Send,
U: Send,
impl<U, REG> Sync for W<U, REG> where
REG: Sync,
U: Sync,
REG: Sync,
U: Sync,
impl<U, REG> Unpin for W<U, REG> where
REG: Unpin,
U: Unpin,
REG: Unpin,
U: Unpin,
Blanket Implementations
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<T> Borrow<T> for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut<T> for T where
T: ?Sized,
[src]
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> From<T> for T
[src]
impl<T, U> Into<U> for T where
U: From<T>,
[src]
U: From<T>,
impl<T, U> TryFrom<U> for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> TryInto<U> for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,