[][src]Struct cortex_m::peripheral::SCB

pub struct SCB { /* fields omitted */ }

System Control Block

Implementations

impl SCB[src]

pub fn vect_active() -> VectActive[src]

Returns the active exception number

impl SCB[src]

pub fn enable_icache(&mut self)[src]

Enables I-Cache if currently disabled

pub fn disable_icache(&mut self)[src]

Disables I-Cache if currently enabled

pub fn icache_enabled() -> bool[src]

Returns whether the I-Cache is currently enabled

pub fn invalidate_icache(&mut self)[src]

Invalidates I-Cache

pub fn enable_dcache(&mut self, cpuid: &mut CPUID)[src]

Enables D-cache if currently disabled

pub fn disable_dcache(&mut self, cpuid: &mut CPUID)[src]

Disables D-cache if currently enabled

pub fn dcache_enabled() -> bool[src]

Returns whether the D-Cache is currently enabled

pub fn clean_dcache(&mut self, cpuid: &mut CPUID)[src]

Cleans D-cache

pub fn clean_invalidate_dcache(&mut self, cpuid: &mut CPUID)[src]

Cleans and invalidates D-cache

pub fn invalidate_dcache_by_address(&mut self, addr: usize, size: usize)[src]

Invalidates D-cache by address

addr: the address to invalidate size: size of the memory block, in number of bytes

Invalidates cache starting from the lowest 32-byte aligned address represented by addr, in blocks of 32 bytes until at least size bytes have been invalidated.

pub fn clean_dcache_by_address(&mut self, addr: usize, size: usize)[src]

Cleans D-cache by address

addr: the address to clean size: size of the memory block, in number of bytes

Cleans cache starting from the lowest 32-byte aligned address represented by addr, in blocks of 32 bytes until at least size bytes have been cleaned.

pub fn clean_invalidate_dcache_by_address(&mut self, addr: usize, size: usize)[src]

Cleans and invalidates D-cache by address

addr: the address to clean and invalidate size: size of the memory block, in number of bytes

Cleans and invalidates cache starting from the lowest 32-byte aligned address represented by addr, in blocks of 32 bytes until at least size bytes have been cleaned and invalidated.

impl SCB[src]

pub fn set_sleepdeep(&mut self)[src]

Set the SLEEPDEEP bit in the SCR register

pub fn clear_sleepdeep(&mut self)[src]

Clear the SLEEPDEEP bit in the SCR register

impl SCB[src]

pub fn set_sleeponexit(&mut self)[src]

Set the SLEEPONEXIT bit in the SCR register

pub fn clear_sleeponexit(&mut self)[src]

Clear the SLEEPONEXIT bit in the SCR register

impl SCB[src]

pub fn system_reset(&mut self) -> ![src]

👎 Deprecated since 0.6.1:

Use SCB::sys_reset

Initiate a system reset request to reset the MCU

pub fn sys_reset() -> ![src]

Initiate a system reset request to reset the MCU

impl SCB[src]

pub fn set_pendsv()[src]

Set the PENDSVSET bit in the ICSR register which will pend the PendSV interrupt

pub fn is_pendsv_pending() -> bool[src]

Check if PENDSVSET bit in the ICSR register is set meaning PendSV interrupt is pending

pub fn clear_pendsv()[src]

Set the PENDSVCLR bit in the ICSR register which will clear a pending PendSV interrupt

pub fn set_pendst()[src]

Set the PENDSTSET bit in the ICSR register which will pend a SysTick interrupt

pub fn is_pendst_pending() -> bool[src]

Check if PENDSTSET bit in the ICSR register is set meaning SysTick interrupt is pending

pub fn clear_pendst()[src]

Set the PENDSTCLR bit in the ICSR register which will clear a pending SysTick interrupt

impl SCB[src]

pub fn get_priority(system_handler: SystemHandler) -> u8[src]

Returns the hardware priority of system_handler

NOTE: Hardware priority does not exactly match logical priority levels. See NVIC.get_priority for more details.

pub unsafe fn set_priority(&mut self, system_handler: SystemHandler, prio: u8)[src]

Sets the hardware priority of system_handler to prio

NOTE: Hardware priority does not exactly match logical priority levels. See NVIC.get_priority for more details.

On ARMv6-M, updating a system handler priority requires a read-modify-write operation. On ARMv7-M, the operation is performed in a single, atomic write operation.

Unsafety

Changing priority levels can break priority-based critical sections (see register::basepri) and compromise memory safety.

pub fn enable(&mut self, exception: Exception)[src]

Enable the exception

If the exception is enabled, when the exception is triggered, the exception handler will be executed instead of the HardFault handler. This function is only allowed on the following exceptions:

  • MemoryManagement
  • BusFault
  • UsageFault
  • SecureFault (can only be enabled from Secure state)

Calling this function with any other exception will do nothing.

pub fn disable(&mut self, exception: Exception)[src]

Disable the exception

If the exception is disabled, when the exception is triggered, the HardFault handler will be executed instead of the exception handler. This function is only allowed on the following exceptions:

  • MemoryManagement
  • BusFault
  • UsageFault
  • SecureFault (can not be changed from Non-secure state)

Calling this function with any other exception will do nothing.

pub fn is_enabled(&self, exception: Exception) -> bool[src]

Check if an exception is enabled

This function is only allowed on the following exception:

  • MemoryManagement
  • BusFault
  • UsageFault
  • SecureFault (can not be read from Non-secure state)

Calling this function with any other exception will read false.

impl SCB[src]

pub fn ptr() -> *const RegisterBlock[src]

Returns a pointer to the register block

Trait Implementations

impl Deref for SCB[src]

type Target = RegisterBlock

The resulting type after dereferencing.

impl Send for SCB[src]

Auto Trait Implementations

impl !Sync for SCB[src]

impl Unpin for SCB[src]

Blanket Implementations

impl<T> Any for T where
    T: 'static + ?Sized
[src]

impl<T> Borrow<T> for T where
    T: ?Sized
[src]

impl<T> BorrowMut<T> for T where
    T: ?Sized
[src]

impl<T> From<T> for T[src]

impl<T, U> Into<U> for T where
    U: From<T>, 
[src]

impl<T> Same<T> for T

type Output = T

Should always be Self

impl<T, U> TryFrom<U> for T where
    U: Into<T>, 
[src]

type Error = Infallible

The type returned in the event of a conversion error.

impl<T, U> TryInto<U> for T where
    U: TryFrom<T>, 
[src]

type Error = <U as TryFrom<T>>::Error

The type returned in the event of a conversion error.