[−][src]Struct cc2650::ioc::iocfg26::W
Value to write to the register
Methods
impl W
[src]
pub fn reset_value() -> W
[src]
Reset value of the register
pub unsafe fn bits(&mut self, bits: u32) -> &mut Self
[src]
Writes raw bits to the register
pub fn hyst_en(&mut self) -> _HYST_ENW
[src]
Bit 30 - 0: Input hysteresis disable 1: Input hysteresis enable
pub fn ie(&mut self) -> _IEW
[src]
Bit 29 - 0: Input disabled 1: Input enabled Note: If IO is configured for AUX ie. PORT_ID = 0x08, the enable will be ignored.
pub fn wu_cfg(&mut self) -> _WU_CFGW
[src]
Bits 27:28 - If DIO is configured GPIO or non-AON peripheral signals, i.e. PORT_ID 0x00 or >0x08: 00: No wake-up 01: No wake-up 10: Wakes up from shutdown if this pad is going low. 11: Wakes up from shutdown if this pad is going high. If IO is configured for AON peripheral signals or AUX ie. PORT_ID 0x01-0x08, this register only sets wakeup enable or not. 00, 01: Wakeup disabled 10, 11: Wakeup enabled Polarity is controlled from AON registers. Note:When the MSB is set, the IOC will deactivate the output enable for the DIO.
pub fn iomode(&mut self) -> _IOMODEW
[src]
Bits 24:26 - IO Mode N/A for IO configured for AON periph. signals and AUX ie. PORT_ID 0x01-0x08 AUX has its own open_source/drain configuration. 0x2: Reserved. Undefined behavior. 0x3: Reserved. Undefined behavior.
pub fn reserved19(&mut self) -> _RESERVED19W
[src]
Bits 19:23 - Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
pub fn edge_irq_en(&mut self) -> _EDGE_IRQ_ENW
[src]
Bit 18 - 0: No interrupt generation 1: Enable interrupt generation for this IO (Only effective if EDGE_DET is enabled)
pub fn edge_det(&mut self) -> _EDGE_DETW
[src]
Bits 16:17 - Enable generation of edge detection events on this IO
pub fn pull_ctl(&mut self) -> _PULL_CTLW
[src]
Bits 13:14 - Pull control
pub fn slew_red(&mut self) -> _SLEW_REDW
[src]
Bit 12 - 0: Normal slew rate 1: Enables reduced slew rate in output driver.
pub fn iocurr(&mut self) -> _IOCURRW
[src]
Bits 10:11 - Selects IO current mode of this IO.
pub fn iostr(&mut self) -> _IOSTRW
[src]
Bits 8:9 - Select source for drive strength control of this IO. This setting controls the drive strength of the Low-Current (LC) mode. Higher drive strength can be selected in IOCURR
pub fn port_id(&mut self) -> _PORT_IDW
[src]
Bits 0:5 - Selects usage for DIO26
Auto Trait Implementations
Blanket Implementations
impl<T> From for T
[src]
impl<T, U> TryFrom for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> TryInto for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
impl<T, U> Into for T where
U: From<T>,
[src]
U: From<T>,
impl<T> Borrow for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut for T where
T: ?Sized,
[src]
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,