Struct cc2650::ccfg::mode_conf::R

pub struct R { /* fields omitted */ }

Value read from the register

Methods

impl R

pub fn bits(&self) -> u32

Value of the register as raw bits

pub fn vddr_trim_sleep_delta(&self) -> VDDR_TRIM_SLEEP_DELTAR

Bits 28:31 - Signed delta value to apply to the VDDR_TRIM_SLEEP target, minus one. See FCFG1:VOLT_TRIM.VDDR_TRIM_SLEEP_H. 0x8 (-8) : Delta = -7 ... 0xF (-1) : Delta = 0 0x0 (0) : Delta = +1 ... 0x7 (7) : Delta = +8

pub fn dcdc_recharge(&self) -> DCDC_RECHARGER

Bit 27 - DC/DC during recharge in powerdown. 0: Use the DC/DC during recharge in powerdown. 1: Do not use the DC/DC during recharge in powerdown (default). NOTE! The DriverLib function SysCtrl_DCDC_VoltageConditionalControl() must be called regularly to apply this field (handled automatically if using TI RTOS!).

pub fn dcdc_active(&self) -> DCDC_ACTIVER

Bit 26 - DC/DC in active mode. 0: Use the DC/DC during active mode. 1: Do not use the DC/DC during active mode (default). NOTE! The DriverLib function SysCtrl_DCDC_VoltageConditionalControl() must be called regularly to apply this field (handled automatically if using TI RTOS!).

pub fn vddr_ext_load(&self) -> VDDR_EXT_LOADR

Bit 25 - Reserved for future use. Software should not rely on the value of a reserved. Writing any other value than the reset/default value may result in undefined behavior.

pub fn vdds_bod_level(&self) -> VDDS_BOD_LEVELR

Bit 24 - VDDS BOD level. 0: VDDS BOD level is 2.0 V (necessary for maximum PA output power on CC13x0). 1: VDDS BOD level is 1.8 V (or 1.7 V for external regulator mode) (default).

pub fn sclk_lf_option(&self) -> SCLK_LF_OPTIONR

Bits 22:23 - Select source for SCLK_LF.

pub fn vddr_trim_sleep_tc(&self) -> VDDR_TRIM_SLEEP_TCR

Bit 21 - 0x1: VDDR_TRIM_SLEEP_DELTA is not temperature compensated 0x0: RTOS/driver temperature compensates VDDR_TRIM_SLEEP_DELTA every time standby mode is entered. This improves low-temperature RCOSC_LF frequency stability in standby mode. When temperature compensation is performed, the delta is calculates this way: Delta = max (delta, min(8, floor(62-temp)/8)) Here, delta is given by VDDR_TRIM_SLEEP_DELTA, and temp is the current temperature in degrees C.

pub fn rtc_comp(&self) -> RTC_COMPR

Bit 20 - Reserved for future use. Software should not rely on the value of a reserved. Writing any other value than the reset/default value may result in undefined behavior.

pub fn xosc_freq(&self) -> XOSC_FREQR

Bits 18:19 - Reserved for future use. Software should not rely on the value of a reserved. Writing any other value than the reset/default value may result in undefined behavior.

pub fn xosc_cap_mod(&self) -> XOSC_CAP_MODR

Bit 17 - Enable modification (delta) to XOSC cap-array. Value specified in XOSC_CAPARRAY_DELTA. 0: Apply cap-array delta 1: Do not apply cap-array delta (default)

pub fn hf_comp(&self) -> HF_COMPR

Bit 16 - Reserved for future use. Software should not rely on the value of a reserved. Writing any other value than the reset/default value may result in undefined behavior.

pub fn xosc_caparray_delta(&self) -> XOSC_CAPARRAY_DELTAR

Bits 8:15 - Signed 8-bit value, directly modifying trimmed XOSC cap-array step value. Enabled by XOSC_CAP_MOD.

pub fn vddr_cap(&self) -> VDDR_CAPR

Bits 0:7 - Unsigned 8-bit integer, representing the minimum decoupling capacitance (worst case) on VDDR, in units of 100nF. This should take into account capacitor tolerance and voltage dependent capacitance variation. This bit affects the recharge period calculation when going into powerdown or standby. NOTE! If using the following functions this field must be configured (used by TI RTOS): SysCtrlSetRechargeBeforePowerDown() SysCtrlAdjustRechargeAfterPowerDown()