Module cc2538_pac::uart1

no description available

Modules

• cc
  UART clock configuration The CC register controls the baud and system clocks sources for the UART module. For more information, see the section called “Baud-Rate Generation”. Note: If the PIOSC is used for the UART baud clock, the system clock frequency must be at least 9 MHz in run mode.
• ctl
  UART control The CTL register is the control register. All the bits are cleared on reset except for the transmit enable (TXE) and receive enable (RXE) bits, which are set. To enable the UART module, the UARTEN bit must be set. If software requires a configuration change in the module, the UARTEN bit must be cleared before the configuration changes are written. If the UART is disabled during a transmit or receive operation, the current transaction is completed before the UART stopping. Note: The UARTCTL register should not be changed while the UART is enabled or else the results are unpredictable. The following sequence is recommended for making changes to the UARTCTL register: 1. Disable the UART. 2. Wait for the end of transmission or reception of the current character. 3. Flush the transmit FIFO by clearing bit 4 (FEN) in the line control register (UARTLCRH). 4. Reprogram the control register. 5. Enable the UART.
• dmactl
  UART DMA control The DMACTL register is the DMA control register.
• dr
  UART data Important: This register is read-sensitive. See the register description for details. This register is the data register (the interface to the FIFOs). For transmitted data, if the FIFO is enabled, data written to this location is pushed onto the transmit FIFO. If the FIFO is disabled, data is stored in the transmitter holding register (the bottom word of the transmit FIFO). A write to this register initiates a transmission from the UART. For received data, if the FIFO is enabled, the data byte and the 4-bit status (break, frame, parity, and overrun) is pushed onto the 12-bit wide receive FIFO. If the FIFO is disabled, the data byte and status are stored in the receiving holding register (the bottom word of the receive FIFO). The received data can be retrieved by reading this register.
• ecr
  UART receive status and error clear The RSR/ECR register is the receive status register/error clear register. A write of any value to the ECR register clears the framing, parity, break, and overrun errors. All the bits are cleared on reset. Write-only error clear register
• fbrd
  UART fractional baud-rate divisor The FBRD register is the fractional part of the baud-rate divisor value. All the bits are cleared on reset. When changing the FBRD register, the new value does not take effect until transmission or reception of the current character is complete. Any changes to the baud-rate divisor must be followed by a write to the LCRH register.
• fr
  UART flag The FR register is the flag register. After reset, the TXFF, RXFF, and BUSY bits are 0, and TXFE and RXFE bits are 1. The CTS bit indicate the modem flow control. Note that the modem bits are only implemented on UART1 and are tied inactive on UART0. Due to this difference, the reset state of the UART0 FR register is 0x90, while UART1 FR register reset state 0x197 .
• ibrd
  UART integer baud-rate divisor The IBRD register is the integer part of the baud-rate divisor value. All the bits are cleared on reset. The minimum possible divide ratio is 1 (when IBRD = 0), in which case the FBRD register is ignored. When changing the IBRD register, the new value does not take effect until transmission or reception of the current character is complete. Any changes to the baud-rate divisor must be followed by a write to the LCRH register.
• icr
  UART interrupt clear The ICR register is the interrupt clear register. On a write of 1, the corresponding interrupt (both raw interrupt and masked interrupt, if enabled) is cleared. A write of 0 has no effect.
• ifls
  UART interrupt FIFO level select The IFLS register is the interrupt FIFO level select register. This register can be used to define the FIFO level at which the TXRIS and RXRIS bits in the RIS register are triggered. The interrupts are generated based on a transition through a level rather than being based on the level. That is, the interrupts are generated when the fill level progresses through the trigger level. For example, if the receive trigger level is set to the half-way mark, the interrupt is triggered as the module is receiving the 9th character. Out of reset, the TXIFLSEL and RXIFLSEL bits are configured so that the FIFOs trigger an interrupt at the half-way mark.
• ilpr
  UART IrDA low-power register The ILPR register stores the 8-bit low-power counter divisor value used to derive the low-power SIR pulse width clock by dividing down the system clock (SysClk). All the bits are cleared when reset. The internal IrLPBaud16 clock is generated by dividing down SysClk according to the low-power divisor value written to ILPR. The duration of SIR pulses generated when low-power mode is enabled is three times the period of the IrLPBaud16 clock. The low-power divisor value is calculated as follows: ILPDVSR = SysClk / FIrLPBaud16 where FIrLPBaud16 is nominally 1.8432 MHz The divisor must be programmed such that FIrLPBaud16 is in the range 1.42 MHz to 2.12 MHz, resulting in a low-power pulse duration of 1.41-2.11 us (three times the period of IrLPBaud16). The minimum frequency of IrLPBaud16 ensures that pulses less than one period of IrLPBaud16 are rejected, but pulses greater than 1.4 us are accepted as valid pulses. Note: Zero is an illegal value. Programming a zero value results in no IrLPBaud16 pulses being generated.
• im
  UART interrupt mask The IM register is the interrupt mask set/clear register. On a read, this register gives the current value of the mask on the relevant interrupt. Setting a bit allows the corresponding raw interrupt signal to be routed to the interrupt controller. Clearing a bit prevents the raw interrupt signal from being sent to the interrupt controller.
• lcrh
  UART line control The LCRH register is the line control register. Serial parameters such as data length, parity, and stop bit selection are implemented in this register. When updating the baud-rate divisor (IBRD and/or IFRD), the LCRH register must also be written. The write strobe for the baud-rate divisor registers is tied to the LCRH register.
• lctl
  UART LIN control The LCTL register is the configures the operation of the UART when in LIN mode.
• lss
  LIN snap shot The LSS register captures the free-running timer value when either the sync edge 1 or the sync edge 5 is detected in LIN mode.
• ltim
  UART LIN timer The LTIM register contains the current timer value for the free-running timer that is used to calculate the baud rate when in LIN slave mode. The value in this register is used along with the value in the UART LIN snap shot (LSS) register to adjust the baud rate to match that of the master.
• mis
  UART masked interrupt status The MIS register is the masked interrupt status register. On a read, this register gives the current masked status value of the corresponding interrupt. A write has no effect.
• ninebitaddr
  UART 9-bit self address The NINEBITADDR register is used to write the specific address that should be matched with the receiving byte when the 9-bit address mask (NINEBITAMASK) is set to 0xFF. This register is used in conjunction with NINEBITAMASK to form a match for address-byte received.
• ninebitamask
  UART 9-bit self address mask The NINEBITAMASK register is used to enable the address mask for 9-bit mode. The lower address bits are masked to create a range of address to be matched with the received address byte.
• pp
  UART peripheral properties The PP register provides information regarding the properties of the UART module.
• ris
  UART raw interrupt status The RIS register is the raw interrupt status register. On a read, this register gives the current raw status value of the corresponding interrupt. A write has no effect. Note that the HW modem flow control bits are only implemented on UART1 and are tied inactive on UART0.
• rsr
  UART receive status and error clear The RSR/ECR register is the receive status register and error clear register. In addition to the DR register, receive status can also be read from the RSR register. If the status is read from this register, then the status information corresponds to the entry read from DR before reading RSR. The status information for overrun is set immediately when an overrun condition occurs. The RSR register cannot be written. Read-only status register

Structs

• RegisterBlock
  Register block

Type Aliases

• Cc
  CC (rw) register accessor: UART clock configuration The CC register controls the baud and system clocks sources for the UART module. For more information, see the section called “Baud-Rate Generation”. Note: If the PIOSC is used for the UART baud clock, the system clock frequency must be at least 9 MHz in run mode.
• Ctl
  CTL (rw) register accessor: UART control The CTL register is the control register. All the bits are cleared on reset except for the transmit enable (TXE) and receive enable (RXE) bits, which are set. To enable the UART module, the UARTEN bit must be set. If software requires a configuration change in the module, the UARTEN bit must be cleared before the configuration changes are written. If the UART is disabled during a transmit or receive operation, the current transaction is completed before the UART stopping. Note: The UARTCTL register should not be changed while the UART is enabled or else the results are unpredictable. The following sequence is recommended for making changes to the UARTCTL register: 1. Disable the UART. 2. Wait for the end of transmission or reception of the current character. 3. Flush the transmit FIFO by clearing bit 4 (FEN) in the line control register (UARTLCRH). 4. Reprogram the control register. 5. Enable the UART.
• Dmactl
  DMACTL (rw) register accessor: UART DMA control The DMACTL register is the DMA control register.
• Dr
  DR (rw) register accessor: UART data Important: This register is read-sensitive. See the register description for details. This register is the data register (the interface to the FIFOs). For transmitted data, if the FIFO is enabled, data written to this location is pushed onto the transmit FIFO. If the FIFO is disabled, data is stored in the transmitter holding register (the bottom word of the transmit FIFO). A write to this register initiates a transmission from the UART. For received data, if the FIFO is enabled, the data byte and the 4-bit status (break, frame, parity, and overrun) is pushed onto the 12-bit wide receive FIFO. If the FIFO is disabled, the data byte and status are stored in the receiving holding register (the bottom word of the receive FIFO). The received data can be retrieved by reading this register.
• Ecr
  ECR (w) register accessor: UART receive status and error clear The RSR/ECR register is the receive status register/error clear register. A write of any value to the ECR register clears the framing, parity, break, and overrun errors. All the bits are cleared on reset. Write-only error clear register
• Fbrd
  FBRD (rw) register accessor: UART fractional baud-rate divisor The FBRD register is the fractional part of the baud-rate divisor value. All the bits are cleared on reset. When changing the FBRD register, the new value does not take effect until transmission or reception of the current character is complete. Any changes to the baud-rate divisor must be followed by a write to the LCRH register.
• Fr
  FR (r) register accessor: UART flag The FR register is the flag register. After reset, the TXFF, RXFF, and BUSY bits are 0, and TXFE and RXFE bits are 1. The CTS bit indicate the modem flow control. Note that the modem bits are only implemented on UART1 and are tied inactive on UART0. Due to this difference, the reset state of the UART0 FR register is 0x90, while UART1 FR register reset state 0x197 .
• Ibrd
  IBRD (rw) register accessor: UART integer baud-rate divisor The IBRD register is the integer part of the baud-rate divisor value. All the bits are cleared on reset. The minimum possible divide ratio is 1 (when IBRD = 0), in which case the FBRD register is ignored. When changing the IBRD register, the new value does not take effect until transmission or reception of the current character is complete. Any changes to the baud-rate divisor must be followed by a write to the LCRH register.
• Icr
  ICR (w) register accessor: UART interrupt clear The ICR register is the interrupt clear register. On a write of 1, the corresponding interrupt (both raw interrupt and masked interrupt, if enabled) is cleared. A write of 0 has no effect.
• Ifls
  IFLS (rw) register accessor: UART interrupt FIFO level select The IFLS register is the interrupt FIFO level select register. This register can be used to define the FIFO level at which the TXRIS and RXRIS bits in the RIS register are triggered. The interrupts are generated based on a transition through a level rather than being based on the level. That is, the interrupts are generated when the fill level progresses through the trigger level. For example, if the receive trigger level is set to the half-way mark, the interrupt is triggered as the module is receiving the 9th character. Out of reset, the TXIFLSEL and RXIFLSEL bits are configured so that the FIFOs trigger an interrupt at the half-way mark.
• Ilpr
  ILPR (rw) register accessor: UART IrDA low-power register The ILPR register stores the 8-bit low-power counter divisor value used to derive the low-power SIR pulse width clock by dividing down the system clock (SysClk). All the bits are cleared when reset. The internal IrLPBaud16 clock is generated by dividing down SysClk according to the low-power divisor value written to ILPR. The duration of SIR pulses generated when low-power mode is enabled is three times the period of the IrLPBaud16 clock. The low-power divisor value is calculated as follows: ILPDVSR = SysClk / FIrLPBaud16 where FIrLPBaud16 is nominally 1.8432 MHz The divisor must be programmed such that FIrLPBaud16 is in the range 1.42 MHz to 2.12 MHz, resulting in a low-power pulse duration of 1.41-2.11 us (three times the period of IrLPBaud16). The minimum frequency of IrLPBaud16 ensures that pulses less than one period of IrLPBaud16 are rejected, but pulses greater than 1.4 us are accepted as valid pulses. Note: Zero is an illegal value. Programming a zero value results in no IrLPBaud16 pulses being generated.
• Im
  IM (rw) register accessor: UART interrupt mask The IM register is the interrupt mask set/clear register. On a read, this register gives the current value of the mask on the relevant interrupt. Setting a bit allows the corresponding raw interrupt signal to be routed to the interrupt controller. Clearing a bit prevents the raw interrupt signal from being sent to the interrupt controller.
• Lcrh
  LCRH (rw) register accessor: UART line control The LCRH register is the line control register. Serial parameters such as data length, parity, and stop bit selection are implemented in this register. When updating the baud-rate divisor (IBRD and/or IFRD), the LCRH register must also be written. The write strobe for the baud-rate divisor registers is tied to the LCRH register.
• Lctl
  LCTL (rw) register accessor: UART LIN control The LCTL register is the configures the operation of the UART when in LIN mode.
• Lss
  LSS (r) register accessor: LIN snap shot The LSS register captures the free-running timer value when either the sync edge 1 or the sync edge 5 is detected in LIN mode.
• Ltim
  LTIM (r) register accessor: UART LIN timer The LTIM register contains the current timer value for the free-running timer that is used to calculate the baud rate when in LIN slave mode. The value in this register is used along with the value in the UART LIN snap shot (LSS) register to adjust the baud rate to match that of the master.
• Mis
  MIS (r) register accessor: UART masked interrupt status The MIS register is the masked interrupt status register. On a read, this register gives the current masked status value of the corresponding interrupt. A write has no effect.
• Ninebitaddr
  NINEBITADDR (rw) register accessor: UART 9-bit self address The NINEBITADDR register is used to write the specific address that should be matched with the receiving byte when the 9-bit address mask (NINEBITAMASK) is set to 0xFF. This register is used in conjunction with NINEBITAMASK to form a match for address-byte received.
• Ninebitamask
  NINEBITAMASK (rw) register accessor: UART 9-bit self address mask The NINEBITAMASK register is used to enable the address mask for 9-bit mode. The lower address bits are masked to create a range of address to be matched with the received address byte.
• Pp
  PP (r) register accessor: UART peripheral properties The PP register provides information regarding the properties of the UART module.
• Ris
  RIS (r) register accessor: UART raw interrupt status The RIS register is the raw interrupt status register. On a read, this register gives the current raw status value of the corresponding interrupt. A write has no effect. Note that the HW modem flow control bits are only implemented on UART1 and are tied inactive on UART0.
• Rsr
  RSR (r) register accessor: UART receive status and error clear The RSR/ECR register is the receive status register and error clear register. In addition to the DR register, receive status can also be read from the RSR register. If the status is read from this register, then the status information corresponds to the entry read from DR before reading RSR. The status information for overrun is set immediately when an overrun condition occurs. The RSR register cannot be written. Read-only status register