[−][src]Struct cc13x2_cc26x2_hal::prcm::clkloadctl::W
Value to write to the register
Methods
impl W
[src]
pub fn reset_value() -> W
[src]
Reset value of the register
pub unsafe fn bits(&mut self, bits: u32) -> &mut Self
[src]
Writes raw bits to the register
pub fn reserved2(&mut self) -> _RESERVED2W
[src]
Bits 2:31 - 31:2] Software should not rely on the value of a reserved. Writing any other value than the reset value may result in undefined behavior.
pub fn load_done(&mut self) -> _LOAD_DONEW
[src]
Bit 1 - 1:1] Status of LOAD. Will be cleared to 0 when any of the registers requiring a LOAD is written to, and be set to 1 when a LOAD is done. Note that writing no change to a register will result in the LOAD_DONE being cleared. 0 : One or more registers have been write accessed after last LOAD 1 : No registers are write accessed after last LOAD
pub fn load(&mut self) -> _LOADW
[src]
Bit 0 - 0:0] 0: No action 1: Load settings to CLKCTRL. Bit is HW cleared. Multiple changes to settings may be done before LOAD is written once so all changes takes place at the same time. LOAD can also be done after single setting updates. Registers that needs to be followed by LOAD before settings being applied are: - SYSBUSCLKDIV - CPUCLKDIV - PERBUSCPUCLKDIV - PERDMACLKDIV - PERBUSCPUCLKG - RFCCLKG - VIMSCLKG - SECDMACLKGR - SECDMACLKGS - SECDMACLKGDS - GPIOCLKGR - GPIOCLKGS - GPIOCLKGDS - GPTCLKGR - GPTCLKGS - GPTCLKGDS - GPTCLKDIV - I2CCLKGR - I2CCLKGS - I2CCLKGDS - SSICLKGR - SSICLKGS - SSICLKGDS - UARTCLKGR - UARTCLKGS - UARTCLKGDS - I2SCLKGR - I2SCLKGS - I2SCLKGDS - I2SBCLKSEL - I2SCLKCTL - I2SMCLKDIV - I2SBCLKDIV - I2SWCLKDIV
Auto Trait Implementations
Blanket Implementations
impl<T> From for T
[src]
impl<T, U> TryFrom for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> TryInto for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
impl<T, U> Into for T where
U: From<T>,
[src]
U: From<T>,
impl<T> Borrow for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut for T where
T: ?Sized,
[src]
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<T> Same for T
type Output = T
Should always be Self