1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83

// Code generated by software.amazon.smithy.rust.codegen.smithy-rs. DO NOT EDIT.
pub use crate::operation::delete_table::_delete_table_output::DeleteTableOutputBuilder;

pub use crate::operation::delete_table::_delete_table_input::DeleteTableInputBuilder;

/// Fluent builder constructing a request to `DeleteTable`.
///
/// <p>The <code>DeleteTable</code> operation deletes a table and all of its items. After a <code>DeleteTable</code> request, the specified table is in the <code>DELETING</code> state until DynamoDB completes the deletion. If the table is in the <code>ACTIVE</code> state, you can delete it. If a table is in <code>CREATING</code> or <code>UPDATING</code> states, then DynamoDB returns a <code>ResourceInUseException</code>. If the specified table does not exist, DynamoDB returns a <code>ResourceNotFoundException</code>. If table is already in the <code>DELETING</code> state, no error is returned. </p> <note>
/// <p>DynamoDB might continue to accept data read and write operations, such as <code>GetItem</code> and <code>PutItem</code>, on a table in the <code>DELETING</code> state until the table deletion is complete.</p>
/// </note>
/// <p>When you delete a table, any indexes on that table are also deleted.</p>
/// <p>If you have DynamoDB Streams enabled on the table, then the corresponding stream on that table goes into the <code>DISABLED</code> state, and the stream is automatically deleted after 24 hours.</p>
/// <p>Use the <code>DescribeTable</code> action to check the status of the table. </p>
#[derive(std::clone::Clone, std::fmt::Debug)]
pub struct DeleteTableFluentBuilder {
    handle: std::sync::Arc<crate::client::Handle>,
    inner: crate::operation::delete_table::builders::DeleteTableInputBuilder,
}
impl DeleteTableFluentBuilder {
    /// Creates a new `DeleteTable`.
    pub(crate) fn new(handle: std::sync::Arc<crate::client::Handle>) -> Self {
        Self {
            handle,
            inner: Default::default(),
        }
    }

    /// Consume this builder, creating a customizable operation that can be modified before being
    /// sent. The operation's inner [http::Request] can be modified as well.
    pub async fn customize(
        self,
    ) -> std::result::Result<
        crate::client::customize::CustomizableOperation<
            crate::operation::delete_table::DeleteTable,
            aws_http::retry::AwsResponseRetryClassifier,
        >,
        aws_smithy_http::result::SdkError<crate::operation::delete_table::DeleteTableError>,
    > {
        let handle = self.handle.clone();
        let operation = self
            .inner
            .build()
            .map_err(aws_smithy_http::result::SdkError::construction_failure)?
            .make_operation(&handle.conf)
            .await
            .map_err(aws_smithy_http::result::SdkError::construction_failure)?;
        Ok(crate::client::customize::CustomizableOperation { handle, operation })
    }

    /// Sends the request and returns the response.
    ///
    /// If an error occurs, an `SdkError` will be returned with additional details that
    /// can be matched against.
    ///
    /// By default, any retryable failures will be retried twice. Retry behavior
    /// is configurable with the [RetryConfig](aws_smithy_types::retry::RetryConfig), which can be
    /// set when configuring the client.
    pub async fn send(
        self,
    ) -> std::result::Result<
        crate::operation::delete_table::DeleteTableOutput,
        aws_smithy_http::result::SdkError<crate::operation::delete_table::DeleteTableError>,
    > {
        let op = self
            .inner
            .build()
            .map_err(aws_smithy_http::result::SdkError::construction_failure)?
            .make_operation(&self.handle.conf)
            .await
            .map_err(aws_smithy_http::result::SdkError::construction_failure)?;
        self.handle.client.call(op).await
    }
    /// <p>The name of the table to delete.</p>
    pub fn table_name(mut self, input: impl Into<std::string::String>) -> Self {
        self.inner = self.inner.table_name(input.into());
        self
    }
    /// <p>The name of the table to delete.</p>
    pub fn set_table_name(mut self, input: std::option::Option<std::string::String>) -> Self {
        self.inner = self.inner.set_table_name(input);
        self
    }
}