Module attiny214

Expand description

The module containing the values for the ‘attiny214’ microcontroller The AVR ATtiny214 microcontroller

§Variants

	Pinout	Mcu age	Operating temperature	Operating voltage	Max speed
ATtiny214-SSFR	SOIC14	SOIC14	-40°C - 125°C	1.8V - 5.5V	20 MHz
ATtiny214-SSNR	SOIC14	SOIC14	-40°C - 105°C	1.8V - 5.5V	20 MHz

Modules§

ac_hysmode: Hysteresis Mode select
ac_intmode: Interrupt Mode select
ac_lpmode: Low Power Mode select
ac_muxneg: Negative Input MUX Selection select
ac_muxpos: Positive Input MUX Selection select
adc_asdv: Automatic Sampling Delay Variation select
adc_dutycyc: Duty Cycle select
adc_initdly: Initial Delay Selection select
adc_muxpos: Analog Channel Selection Bits select
adc_presc: Clock Pre-scaler select
adc_refsel: Reference Selection select
adc_ressel: ADC Resolution select
adc_sampnum: Accumulation Samples select
adc_wincm: Window Comparator Mode select
bod_active: Operation in active mode select
bod_lvl: Bod level select
bod_sampfreq: Sample frequency select
bod_sleep: Operation in sleep mode select
bod_vlmcfg: Configuration select
bod_vlmlvl: voltage level monitor level select
ccl_edgedet: Edge Detection Enable select
ccl_filtsel: Filter Selection select
ccl_insel0: LUT Input 0 Source Selection select
ccl_insel1: LUT Input 1 Source Selection select
ccl_insel2: LUT Input 2 Source Selection select
ccl_seqsel: Sequential Selection select
clkctrl_clksel: clock select select
clkctrl_csut: Crystal startup time select
clkctrl_pdiv: Prescaler division select
cpu_ccp: CCP signature select
crcscan_mode: CRC Flash Access Mode select
crcscan_src: CRC Source select
evsys_asyncch0: Asynchronous Channel 0 Generator Selection select
evsys_asyncch1: Asynchronous Channel 1 Generator Selection select
evsys_asyncch2: Asynchronous Channel 2 Generator Selection select
evsys_asyncch3: Asynchronous Channel 3 Generator Selection select
evsys_asyncuser0: Asynchronous User Ch 0 Input Selection - TCB0 select
evsys_asyncuser1: Asynchronous User Ch 1 Input Selection - ADC0 select
evsys_asyncuser2: Asynchronous User Ch 2 Input Selection - CCL LUT0 Event 0 select
evsys_asyncuser3: Asynchronous User Ch 3 Input Selection - CCL LUT1 Event 0 select
evsys_asyncuser4: synchronous User Ch 4 Input Selection - CCL LUT0 Event 1 select
evsys_asyncuser5: Asynchronous User Ch 5 Input Selection - CCL LUT1 Event 1 select
evsys_asyncuser6: Asynchronous User Ch 6 Input Selection - TCD0 Event 0 select
evsys_asyncuser7: Asynchronous User Ch 7 Input Selection - TCD0 Event 1 select
evsys_asyncuser8: Asynchronous User Ch 8 Input Selection - Event Out 0 select
evsys_asyncuser9: Asynchronous User Ch 9 Input Selection - Event Out 1 select
evsys_asyncuser10: Asynchronous User Ch 10 Input Selection - Event Out 2 select
evsys_syncch0: Synchronous Channel 0 Generator Selection select
evsys_syncch1: Synchronous Channel 1 Generator Selection select
evsys_syncuser0: Synchronous User Ch 0 Input Selection - TCA0 select
evsys_syncuser1: Synchronous User Ch 1 Input Selection - USART0 select
fuse_active: BOD Operation in Active Mode select
fuse_crcsrc: CRC Source select
fuse_freqsel: Frequency Select select
fuse_lvl: BOD Level select
fuse_period: Watchdog Timeout Period select
fuse_rstpincfg: Reset Pin Configuration select
fuse_sampfreq: BOD Sample Frequency select
fuse_sleep: BOD Operation in Sleep Mode select
fuse_sut: Startup Time select
fuse_window: Watchdog Window Timeout Period select
lockbit_lb: Lock Bits select
nvmctrl_cmd: Command select
port_isc: Input/Sense Configuration select
portmux_lut0: Configurable Custom Logic LUT0 select
portmux_lut1: Configurable Custom Logic LUT1 select
portmux_spi0: Port Multiplexer SPI0 select
portmux_tca00: Port Multiplexer TCA0 Output 0 select
portmux_tca01: Port Multiplexer TCA0 output 1 select
portmux_tca02: Port Multiplexer TCA0 Output 2 select
portmux_tca03: Port Multiplexer TCA0 Output 3 select
portmux_tca04: Port Multiplexer TCA0 Output 4 select
portmux_tca05: Port Multiplexer TCA0 Output 5 select
portmux_tcb0: Port Multiplexer TCB select
portmux_twi0: Port Multiplexer TWI0 select
portmux_usart0: Port Multiplexer USART0 select
rtc_clksel: Clock Select select
rtc_period: Period select
rtc_prescaler: Prescaling Factor select
slpctrl_smode: Sleep mode select
spi_mode: SPI Mode select
spi_presc: Prescaler select
tca_single_clksel: Clock Selection select
tca_single_cmd: Command select
tca_single_dir: Direction select
tca_single_evact: Event Action select
tca_single_wgmode: Waveform generation mode select
tca_split_clksel: Clock Selection select
tca_split_cmd: Command select
tcb_clksel: Clock Select select
tcb_cntmode: Timer Mode select
tcd_action: event action select
tcd_cfg: event config select
tcd_clksel: clock select select
tcd_cmpcsel: Compare C output select select
tcd_cmpdsel: Compare D output select select
tcd_cntpres: counter prescaler select
tcd_dithersel: dither select select
tcd_dlypresc: Delay prescaler select
tcd_dlysel: Delay select select
tcd_dlytrig: Delay trigger select
tcd_edge: edge select select
tcd_inputmode: Input mode select
tcd_syncpres: Syncronization prescaler select
tcd_wgmode: Waveform generation mode select
twi_ackact: Acknowledge Action select
twi_ap: Slave Address or Stop select
twi_busstate: Bus State select
twi_mcmd: Command select
twi_scmd: Command select
twi_sdahold: SDA Hold Time select
twi_sdasetup: SDA Setup Time select
twi_timeout: Inactive Bus Timeout select
usart_mspi_cmode: Communication Mode select
usart_normal_chsize: Character Size select
usart_normal_cmode: Communication Mode select
usart_normal_pmode: Parity Mode select
usart_normal_sbmode: Stop Bit Mode select
usart_rs485: RS485 Mode internal transmitter select
usart_rxmode: Receiver Mode select
vref_adc0refsel: ADC0 reference select select
vref_dac0refsel: DAC0/AC0 reference select select
wdt_period: Period select
wdt_window: Window select

Constants§

ABMBP: Bitfield on register DBGCTRL
ACTIVE: Bitfield on register BODCFG
ADC0REFEN: Bitfield on register CTRLB
ADDR: Address.
ADDREN: Bitfield on register SADDRMASK
ADDRH: Address high byte.
ADDRL: Address low byte.
ADDRMASK: Bitfield on register SADDRMASK
AP: Bitfield on register SSTATUS
APIEN: Bitfield on register SCTRLA
APIF: Bitfield on register SSTATUS
APPEND: Application Code Section End.
ARBLOST: Bitfield on register MSTATUS
ASYNCCH0: Asynchronous Channel 0 Generator Selection.
ASYNCCH1: Asynchronous Channel 1 Generator Selection.
ASYNCCH2: Asynchronous Channel 2 Generator Selection.
ASYNCCH3: Asynchronous Channel 3 Generator Selection.
ASYNCSTROBE: Asynchronous Channel Strobe.
ASYNCUSER0: Asynchronous User Ch 0 Input Selection - TCB0.
ASYNCUSER1: Asynchronous User Ch 1 Input Selection - ADC0.
ASYNCUSER2: Asynchronous User Ch 2 Input Selection - CCL LUT0 Event 0.
ASYNCUSER3: Asynchronous User Ch 3 Input Selection - CCL LUT1 Event 0.
ASYNCUSER4: Asynchronous User Ch 4 Input Selection - CCL LUT0 Event 1.
ASYNCUSER5: Asynchronous User Ch 5 Input Selection - CCL LUT1 Event 1.
ASYNCUSER6: Asynchronous User Ch 6 Input Selection - TCD0 Event 0.
ASYNCUSER7: Asynchronous User Ch 7 Input Selection - TCD0 Event 1.
ASYNCUSER8: Asynchronous User Ch 8 Input Selection - Event Out 0.
ASYNCUSER9: Asynchronous User Ch 9 Input Selection - Event Out 1.
ASYNCUSER10: Asynchronous User Ch 10 Input Selection - Event Out 2.
BAUD: Baud Rate.
BAUDH: Baud Rate high byte.
BAUDL: Baud Rate low byte.
BODCFG: BOD Configuration.
BOOTEND: Boot Section End.
BORF: Bitfield on register RSTFR
BUFOVF: Bitfield on register RXDATAH
BUSSTATE: Bitfield on register MSTATUS
C: Bitfield on register SREG
CAL20M: Bitfield on register OSC20MCALIBA
CALIB: Calibration.
CALSEL20M: Bitfield on register OSC20MCALIBA
CAPTUREA: Capture A.
CAPTUREAH: Capture A high byte.
CAPTUREAL: Capture A low byte.
CAPTUREB: Capture B.
CAPTUREBH: Capture B high byte.
CAPTUREBL: Capture B low byte.
CCMP: Compare or Capture.
CCMPH: Compare or Capture high byte.
CCMPL: Compare or Capture low byte.
CCP: Configuration Change Protection.
CLKOUT: Bitfield on register MCLKCTRLA
CLKSEL: Clock Select.
CMP: Compare.
CMP0: Compare 0.
CMP0BUF: Compare 0 Buffer.
CMP0BUFH: Compare 0 Buffer high byte.
CMP0BUFL: Compare 0 Buffer low byte.
CMP0H: Compare 0 high byte.
CMP0L: Compare 0 low byte.
CMP1: Compare 1.
CMP2: Compare 2.
CMP1BUF: Compare 1 Buffer.
CMP1BUFH: Compare 1 Buffer high byte.
CMP1BUFL: Compare 1 Buffer low byte.
CMP1H: Compare 1 high byte.
CMP1L: Compare 1 low byte.
CMP2BUF: Compare 2 Buffer.
CMP2BUFH: Compare 2 Buffer high byte.
CMP2BUFL: Compare 2 Buffer low byte.
CMP2H: Compare 2 high byte.
CMP2L: Compare 2 low byte.
CMPACLR: Compare A Clear.
CMPACLRH: Compare A Clear high byte.
CMPACLRL: Compare A Clear low byte.
CMPASET: Compare A Set.
CMPASETH: Compare A Set high byte.
CMPASETL: Compare A Set low byte.
CMPAVAL: Bitfield on register CTRLD
CMPBCLR: Compare B Clear.
CMPBCLRH: Compare B Clear high byte.
CMPBCLRL: Compare B Clear low byte.
CMPBSET: Compare B Set.
CMPBSETH: Compare B Set high byte.
CMPBSETL: Compare B Set low byte.
CMPBVAL: Bitfield on register CTRLD
CMPH: Compare high byte.
CMPL: Compare low byte.
CNT: Count.
CNTH: Count high byte.
CNTL: Count low byte.
COLL: Bitfield on register SSTATUS
COMMAND: Command.
CRCSRC: Bitfield on register SYSCFG0
CSUT: Bitfield on register XOSC32KCTRLA
CTRLA: Control A.
CTRLB: Control B.
CTRLBUSY: Bitfield on register PITSTATUS
CTRLC: Control C.
CTRLD: Control D.
CTRLE: Control E.
CTRLECLR: Control E Clear.
CTRLESET: Control E Set.
CTRLFCLR: Control F Clear.
CTRLFSET: Control F Set.
DAC0REFEN: Bitfield on register CTRLB
DATA: Data.
DBGCTRL: Debug Control.
DEVICEID0: Device ID Byte 0.
DEVICEID1: Device ID Byte 1.
DEVICEID2: Device ID Byte 2.
DIEN: Bitfield on register SCTRLA
DIF: Bitfield on register SSTATUS
DIR: Data Direction.
DIRCLR: Data Direction Clear.
DIRSET: Data Direction Set.
DIRTGL: Data Direction Toggle.
DISEOC: Bitfield on register CTRLE
DITCTRL: Dither Control A.
DITHER: Bitfield on register DITVAL
DITHERSEL: Bitfield on register DITCTRL
DITVAL: Dither value.
DLYCTRL: Delay Control.
DLYPRESC: Bitfield on register DLYCTRL
DLYSEL: Bitfield on register DLYCTRL
DLYTRIG: Bitfield on register DLYCTRL
DLYVAL: Delay value.
DUTYCYC: Bitfield on register CALIB
EESAVE: Bitfield on register SYSCFG0
ENEXTBRK: Bitfield on register EXTBRK
EVCTRL: Event Control.
EVCTRLA: EVCTRLA.
EVCTRLB: EVCTRLB.
EXTBRK: External Break.
EXTRF: Bitfield on register RSTFR
EXTS: Bitfield on register MCLKSTATUS
FAULTCTRL: Fault Control.
FERR: Bitfield on register RXDATAH
FLUSH: Bitfield on register MCTRLB
FREQSEL: Bitfield on register OSCCFG
GPIOR0: General Purpose IO Register 0.
GPIOR1: General Purpose IO Register 1.
GPIOR2: General Purpose IO Register 2.
GPIOR3: General Purpose IO Register 3.
H: Bitfield on register SREG
HCMP0: High Compare.
HCMP1: High Compare.
HCMP2: High Compare.
HCNT: High Count.
HPER: High Period.
I: Bitfield on register SREG
IN: Input Value.
INPUTCTRLA: Input Control A.
INPUTCTRLB: Input Control B.
INTCTRL: Interrupt Control.
INTFLAGS: Interrupt Flags.
INVERT: Bitfield on register MUXCTRLA
IREI: Bitfield on register EVCTRL
LCMP0: Low Compare.
LCMP1: Low Compare.
LCMP2: Low Compare.
LCNT: Low Count.
LOCKBIT: Lock bits.
LOCKEN: Bitfield on register MCLKLOCK
LPER: Low Period.
LUT0CTRLA: LUT Control 0 A.
LUT0CTRLB: LUT Control 0 B.
LUT0CTRLC: LUT Control 0 C.
LUT1CTRLA: LUT Control 1 A.
LUT1CTRLB: LUT Control 1 B.
LUT1CTRLC: LUT Control 1 C.
LVL: Bitfield on register BODCFG
LVL0PRI: Interrupt Level 0 Priority.
LVL1VEC: Interrupt Level 1 Priority Vector.
MADDR: Master Address.
MBAUD: Master Baurd Rate Control.
MCLKCTRLA: MCLK Control A.
MCLKCTRLB: MCLK Control B.
MCLKLOCK: MCLK Lock.
MCLKSTATUS: MCLK Status.
MCMD: Bitfield on register MCTRLB
MCTRLA: Master Control A.
MCTRLB: Master Control B.
MDATA: Master Data.
MSTATUS: Master Status.
MUXCTRLA: Mux Control A.
MUXNEG: Bitfield on register MUXCTRLA
MUXPOS: Positive mux input.
N: Bitfield on register SREG
OSC16ERR3V: OSC16 error at 3V.
OSC16ERR5V: OSC16 error at 5V.
OSC20ERR3V: OSC20 error at 3V.
OSC20ERR5V: OSC20 error at 5V.
OSC20MCALIBA: OSC20M Calibration A.
OSC20MCALIBB: OSC20M Calibration B.
OSC20MCTRLA: OSC20M Control A.
OSC20MS: Bitfield on register MCLKSTATUS
OSC32KCTRLA: OSC32K Control A.
OSC32KS: Bitfield on register MCLKSTATUS
OSCCFG: Oscillator Configuration.
OSCLOCK: Bitfield on register OSCCFG
OUT: Output Value.
OUTCLR: Output Value Clear.
OUTSET: Output Value Set.
OUTTGL: Output Value Toggle.
OVF: Bitfield on register INTCTRL
PDIV: Bitfield on register MCLKCTRLB
PEN: Bitfield on register MCLKCTRLB
PER: Period.
PERBUF: Period Buffer.
PERBUFH: Period Buffer high byte.
PERBUFL: Period Buffer low byte.
PERH: Period high byte.
PERL: Period low byte.
PERR: Bitfield on register RXDATAH
PIEN: Bitfield on register SCTRLA
PIN0CTRL: Pin 0 Control.
PIN1CTRL: Pin 1 Control.
PIN2CTRL: Pin 2 Control.
PIN3CTRL: Pin 3 Control.
PIN4CTRL: Pin 4 Control.
PIN5CTRL: Pin 5 Control.
PIN6CTRL: Pin 6 Control.
PIN7CTRL: Pin 7 Control.
PITCTRLA: PIT Control A.
PITDBGCTRL: PIT Debug control.
PITEN: Bitfield on register PITCTRLA
PITINTCTRL: PIT Interrupt Control.
PITINTFLAGS: PIT Interrupt Flags.
PITSTATUS: PIT Status.
PMEN: Bitfield on register SCTRLA
PORF: Bitfield on register RSTFR
QCEN: Bitfield on register MCTRLA
RES: ADC Accumulator Result.
RESH: ADC Accumulator Result high byte.
RESL: ADC Accumulator Result low byte.
RESTART: Bitfield on register CTRLE
REVID: Revision ID.
RIEN: Bitfield on register MCTRLA
RIF: Bitfield on register MSTATUS
RSTFR: Reset Flags.
RSTPINCFG: Bitfield on register SYSCFG0
RXCIF: Bitfield on register RXDATAH
RXDATAH: Receive Data High Byte.
RXDATAL: Receive Data Low Byte.
RXPL: Bitfield on register RXPLCTRL
RXPLCTRL: IRCOM Receiver Pulse Length Control.
S: Bitfield on register SREG
SADDR: Slave Address.
SADDRMASK: Slave Address Mask.
SAMPCTRL: Sample Control.
SAMPFREQ: Bitfield on register BODCFG
SAMPLEN: Bitfield on register SAMPCTRL
SCAPTUREA: Bitfield on register CTRLE
SCAPTUREB: Bitfield on register CTRLE
SCMD: Bitfield on register SCTRLB
SCTRLA: Slave Control A.
SCTRLB: Slave Control B.
SDATA: Slave Data.
SEL: Bitfield on register XOSC32KCTRLA
SEQCTRL0: Sequential Control 0.
SEQSEL: Bitfield on register SEQCTRL0
SERNUM0: Serial Number Byte 0.
SERNUM1: Serial Number Byte 1.
SERNUM2: Serial Number Byte 2.
SERNUM3: Serial Number Byte 3.
SERNUM4: Serial Number Byte 4.
SERNUM5: Serial Number Byte 5.
SERNUM6: Serial Number Byte 6.
SERNUM7: Serial Number Byte 7.
SERNUM8: Serial Number Byte 8.
SERNUM9: Serial Number Byte 9.
SLEEP: Bitfield on register BODCFG
SOSC: Bitfield on register MCLKSTATUS
SPH: Stack Pointer High.
SPL: Stack Pointer Low.
SREG: Status Register.
SSTATUS: Slave Status.
STATUS: Status.
STCONV: Bitfield on register COMMAND
SUT: Bitfield on register SYSCFG1
SWRE: Bitfield on register SWRR
SWRF: Bitfield on register RSTFR
SWRR: Software Reset.
SYNC: Bitfield on register CTRLE
SYNCBUSY: Bitfield on register STATUS
SYNCCH0: Synchronous Channel 0 Generator Selection.
SYNCCH1: Synchronous Channel 1 Generator Selection.
SYNCEOC: Bitfield on register CTRLE
SYNCSTROBE: Synchronous Channel Strobe.
SYNCUSER0: Synchronous User Ch 0 Input Selection - TCA0.
SYNCUSER1: Synchronous User Ch 1 Input Selection - USART0.
SYSCFG0: System Configuration 0.
SYSCFG1: System Configuration 1.
T: Bitfield on register SREG
TCD0CFG: TCD0 Configuration.
TEMP: Temporary Value.
TEMPCAL20M: Bitfield on register OSC20MCALIBB
TEMPSENSE0: Temperature Sensor Calibration Byte 0.
TEMPSENSE1: Temperature Sensor Calibration Byte 1.
TIMEOUT: Bitfield on register MCTRLA
TRIGA: Bitfield on register INTCTRL
TRIGB: Bitfield on register INTCTRL
TRUTH0: Truth 0.
TRUTH1: Truth 1.
TXDATAH: Transmit Data High Byte.
TXDATAL: Transmit Data Low Byte.
TXPLCTRL: IRCOM Transmitter Pulse Length Control.
UPDIRF: Bitfield on register RSTFR
USERROW0: User Row Byte 0.
USERROW1: User Row Byte 1.
USERROW2: User Row Byte 2.
USERROW3: User Row Byte 3.
USERROW4: User Row Byte 4.
USERROW5: User Row Byte 5.
USERROW6: User Row Byte 6.
USERROW7: User Row Byte 7.
USERROW8: User Row Byte 8.
USERROW9: User Row Byte 9.
USERROW10: User Row Byte 10.
USERROW11: User Row Byte 11.
USERROW12: User Row Byte 12.
USERROW13: User Row Byte 13.
USERROW14: User Row Byte 14.
USERROW15: User Row Byte 15.
USERROW16: User Row Byte 16.
USERROW17: User Row Byte 17.
USERROW18: User Row Byte 18.
USERROW19: User Row Byte 19.
USERROW20: User Row Byte 20.
USERROW21: User Row Byte 21.
USERROW22: User Row Byte 22.
USERROW23: User Row Byte 23.
USERROW24: User Row Byte 24.
USERROW25: User Row Byte 25.
USERROW26: User Row Byte 26.
USERROW27: User Row Byte 27.
USERROW28: User Row Byte 28.
USERROW29: User Row Byte 29.
USERROW30: User Row Byte 30.
USERROW31: User Row Byte 31.
V: Bitfield on register SREG
VLMCTRLA: Voltage level monitor Control.
VLMLVL: Bitfield on register VLMCTRLA
WDRF: Bitfield on register RSTFR
WDTCFG: Watchdog Configuration.
WIEN: Bitfield on register MCTRLA
WIF: Bitfield on register MSTATUS
WINHT: Window comparator high threshold.
WINHTH: Window comparator high threshold high byte.
WINHTL: Window comparator high threshold low byte.
WINLT: Window comparator low threshold.
WINLTH: Window comparator low threshold high byte.
WINLTL: Window comparator low threshold low byte.
XOSC32KCTRLA: XOSC32K Control A.
XOSC32KS: Bitfield on register MCLKSTATUS
Z: Bitfield on register SREG

Module attiny214

Module attiny214 Copy item path

§Variants

Modules§

Constants§

Module attiny214