[−][src]Struct arduino_mkr1000::sercom::UART0
UARTX represents the corresponding SERCOMX instance
configured to act in the role of a UART Master.
Objects of this type implement the HAL serial::Read
,
serial::Write
traits.
This type is generic over any valid pad mapping where there is a defined "receive pin out transmit pin out" implementation.
Implementations
impl<RX, TX, RTS, CTS> UART0<RX, TX, RTS, CTS>
[src]
pub fn new<F, T>(
clock: &Sercom0CoreClock,
freq: F,
sercom: SERCOM0,
pm: &mut PM,
padout: T
) -> UART0<RX, TX, RTS, CTS> where
F: Into<Hertz>,
T: Into<UART0Padout<RX, TX, RTS, CTS>>,
UART0Padout<RX, TX, RTS, CTS>: RxpoTxpo,
[src]
clock: &Sercom0CoreClock,
freq: F,
sercom: SERCOM0,
pm: &mut PM,
padout: T
) -> UART0<RX, TX, RTS, CTS> where
F: Into<Hertz>,
T: Into<UART0Padout<RX, TX, RTS, CTS>>,
UART0Padout<RX, TX, RTS, CTS>: RxpoTxpo,
Power on and configure SERCOMX to work as a UART Master operating with the specified frequency. The padout specifies which pins are bound to the RX, TX and optionally RTS and CTS functions.
You can use any tuple of two or four SercomXPadY instances for which there exists a From implementation for UARTXPadout.
pub fn free(self) -> (UART0Padout<RX, TX, RTS, CTS>, SERCOM0)
[src]
Trait Implementations
impl<RX, TX, RTS, CTS> Default<u8> for UART0<RX, TX, RTS, CTS>
[src]
impl<RX, TX, RTS, CTS> Read<u8> for UART0<RX, TX, RTS, CTS>
[src]
type Error = ()
Read error
fn read(
&mut self
) -> Result<u8, Error<<UART0<RX, TX, RTS, CTS> as Read<u8>>::Error>>
[src]
&mut self
) -> Result<u8, Error<<UART0<RX, TX, RTS, CTS> as Read<u8>>::Error>>
impl<RX, TX, RTS, CTS> Write<u8> for UART0<RX, TX, RTS, CTS>
[src]
type Error = ()
Write error
fn write(
&mut self,
word: u8
) -> Result<(), Error<<UART0<RX, TX, RTS, CTS> as Write<u8>>::Error>>
[src]
&mut self,
word: u8
) -> Result<(), Error<<UART0<RX, TX, RTS, CTS> as Write<u8>>::Error>>
fn flush(
&mut self
) -> Result<(), Error<<UART0<RX, TX, RTS, CTS> as Write<u8>>::Error>>
[src]
&mut self
) -> Result<(), Error<<UART0<RX, TX, RTS, CTS> as Write<u8>>::Error>>
impl<RX, TX, RTS, CTS> Write for UART0<RX, TX, RTS, CTS>
[src]
Auto Trait Implementations
impl<RX, TX, RTS, CTS> Send for UART0<RX, TX, RTS, CTS> where
CTS: Send,
RTS: Send,
RX: Send,
TX: Send,
CTS: Send,
RTS: Send,
RX: Send,
TX: Send,
impl<RX, TX, RTS, CTS> !Sync for UART0<RX, TX, RTS, CTS>
impl<RX, TX, RTS, CTS> Unpin for UART0<RX, TX, RTS, CTS> where
CTS: Unpin,
RTS: Unpin,
RX: Unpin,
TX: Unpin,
CTS: Unpin,
RTS: Unpin,
RX: Unpin,
TX: Unpin,
Blanket Implementations
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<T> Borrow<T> for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut<T> for T where
T: ?Sized,
[src]
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> From<T> for T
[src]
impl<T, U> Into<U> for T where
U: From<T>,
[src]
U: From<T>,
impl<T> Same<T> for T
type Output = T
Should always be Self
impl<T, U> TryFrom<U> for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> TryInto<U> for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
impl<S, Word> Write<Word> for S where
S: Default<Word>,
Word: Clone,
[src]
S: Default<Word>,
Word: Clone,