Module stm32h7xx_hal::device::rtc::isr [−][src]
This register is write protected (except for RTC_ISR[13:8] bits). The write access procedure is described in RTC register write protection on page9.
Structs
| ALRAF_W | Write proxy for field |
| ALRBF_W | Write proxy for field |
| INIT_W | Write proxy for field |
| ITSF_W | Write proxy for field |
| RSF_W | Write proxy for field |
| TAMP1F_W | Write proxy for field |
| TAMP2F_W | Write proxy for field |
| TAMP3F_W | Write proxy for field |
| TSF_W | Write proxy for field |
| TSOVF_W | Write proxy for field |
| WUTF_W | Write proxy for field |
Enums
| ALRAF_A | Alarm A flag This flag is set by hardware when the time/date registers (RTC_TR and RTC_DR) match the Alarm A register (RTC_ALRMAR). This flag is cleared by software by writing 0. |
| ALRAF_AW | Alarm A flag This flag is set by hardware when the time/date registers (RTC_TR and RTC_DR) match the Alarm A register (RTC_ALRMAR). This flag is cleared by software by writing 0. |
| ALRAWF_A | Alarm A write flag This bit is set by hardware when Alarm A values can be changed, after the ALRAE bit has been set to 0 in RTC_CR. It is cleared by hardware in initialization mode. |
| ALRBF_A | Alarm B flag This flag is set by hardware when the time/date registers (RTC_TR and RTC_DR) match the Alarm B register (RTC_ALRMBR). This flag is cleared by software by writing 0. |
| ALRBF_AW | Alarm B flag This flag is set by hardware when the time/date registers (RTC_TR and RTC_DR) match the Alarm B register (RTC_ALRMBR). This flag is cleared by software by writing 0. |
| INITF_A | Initialization flag When this bit is set to 1, the RTC is in initialization state, and the time, date and prescaler registers can be updated. |
| INITS_A | Initialization status flag This bit is set by hardware when the calendar year field is different from 0 (Backup domain reset state). |
| INIT_A | Initialization mode |
| ITSF_A | Internal tTime-stamp flag |
| ITSF_AW | Internal tTime-stamp flag |
| RECALPF_A | Recalibration pending Flag The RECALPF status flag is automatically set to 1 when software writes to the RTC_CALR register, indicating that the RTC_CALR register is blocked. When the new calibration settings are taken into account, this bit returns to 0. Refer to Re-calibration on-the-fly. |
| RSF_A | Registers synchronization flag This bit is set by hardware each time the calendar registers are copied into the shadow registers (RTC_SSRx, RTC_TRx and RTC_DRx). This bit is cleared by hardware in initialization mode, while a shift operation is pending (SHPF=1), or when in bypass shadow register mode (BYPSHAD=1). This bit can also be cleared by software. It is cleared either by software or by hardware in initialization mode. |
| RSF_AW | Registers synchronization flag This bit is set by hardware each time the calendar registers are copied into the shadow registers (RTC_SSRx, RTC_TRx and RTC_DRx). This bit is cleared by hardware in initialization mode, while a shift operation is pending (SHPF=1), or when in bypass shadow register mode (BYPSHAD=1). This bit can also be cleared by software. It is cleared either by software or by hardware in initialization mode. |
| SHPF_A | Shift operation pending This flag is set by hardware as soon as a shift operation is initiated by a write to the RTC_SHIFTR register. It is cleared by hardware when the corresponding shift operation has been executed. Writing to the SHPF bit has no effect. |
| TAMP1F_A | RTC_TAMP1 detection flag This flag is set by hardware when a tamper detection event is detected on the RTC_TAMP1 input. It is cleared by software writing 0 |
| TAMP1F_AW | RTC_TAMP1 detection flag This flag is set by hardware when a tamper detection event is detected on the RTC_TAMP1 input. It is cleared by software writing 0 |
| TSF_A | Time-stamp flag This flag is set by hardware when a time-stamp event occurs. This flag is cleared by software by writing 0. |
| TSF_AW | Time-stamp flag This flag is set by hardware when a time-stamp event occurs. This flag is cleared by software by writing 0. |
| TSOVF_A | Time-stamp overflow flag This flag is set by hardware when a time-stamp event occurs while TSF is already set. This flag is cleared by software by writing 0. It is recommended to check and then clear TSOVF only after clearing the TSF bit. Otherwise, an overflow might not be noticed if a time-stamp event occurs immediately before the TSF bit is cleared. |
| TSOVF_AW | Time-stamp overflow flag This flag is set by hardware when a time-stamp event occurs while TSF is already set. This flag is cleared by software by writing 0. It is recommended to check and then clear TSOVF only after clearing the TSF bit. Otherwise, an overflow might not be noticed if a time-stamp event occurs immediately before the TSF bit is cleared. |
| WUTF_A | Wakeup timer flag This flag is set by hardware when the wakeup auto-reload counter reaches 0. This flag is cleared by software by writing 0. This flag must be cleared by software at least 1.5 RTCCLK periods before WUTF is set to 1 again. |
| WUTF_AW | Wakeup timer flag This flag is set by hardware when the wakeup auto-reload counter reaches 0. This flag is cleared by software by writing 0. This flag must be cleared by software at least 1.5 RTCCLK periods before WUTF is set to 1 again. |
| WUTWF_A | Wakeup timer write flag This bit is set by hardware up to 2 RTCCLK cycles after the WUTE bit has been set to 0 in RTC_CR, and is cleared up to 2 RTCCLK cycles after the WUTE bit has been set to 1. The wakeup timer values can be changed when WUTE bit is cleared and WUTWF is set. |
Type Definitions
| ALRAF_R | Reader of field |
| ALRAWF_R | Reader of field |
| ALRBF_R | Reader of field |
| ALRBWF_A | Alarm B write flag This bit is set by hardware when Alarm B values can be changed, after the ALRBE bit has been set to 0 in RTC_CR. It is cleared by hardware in initialization mode. |
| ALRBWF_R | Reader of field |
| INITF_R | Reader of field |
| INITS_R | Reader of field |
| INIT_R | Reader of field |
| ITSF_R | Reader of field |
| R | Reader of register ISR |
| RECALPF_R | Reader of field |
| RSF_R | Reader of field |
| SHPF_R | Reader of field |
| TAMP1F_R | Reader of field |
| TAMP2F_A | RTC_TAMP2 detection flag This flag is set by hardware when a tamper detection event is detected on the RTC_TAMP2 input. It is cleared by software writing 0 |
| TAMP2F_AW | RTC_TAMP2 detection flag This flag is set by hardware when a tamper detection event is detected on the RTC_TAMP2 input. It is cleared by software writing 0 |
| TAMP2F_R | Reader of field |
| TAMP3F_A | RTC_TAMP3 detection flag This flag is set by hardware when a tamper detection event is detected on the RTC_TAMP3 input. It is cleared by software writing 0 |
| TAMP3F_AW | RTC_TAMP3 detection flag This flag is set by hardware when a tamper detection event is detected on the RTC_TAMP3 input. It is cleared by software writing 0 |
| TAMP3F_R | Reader of field |
| TSF_R | Reader of field |
| TSOVF_R | Reader of field |
| W | Writer for register ISR |
| WUTF_R | Reader of field |
| WUTWF_R | Reader of field |