Expand description
Control register 3
Structs
Type Definitions
Field CTSE reader - CTS enable This bit can only be written when the USART is disabled (UEÂ =Â 0) Note: If the hardware flow control feature is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field CTSE writer - CTS enable This bit can only be written when the USART is disabled (UEÂ =Â 0) Note: If the hardware flow control feature is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field CTSIE reader - CTS interrupt enable Note: If the hardware flow control feature is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field CTSIE writer - CTS interrupt enable Note: If the hardware flow control feature is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field DDRE reader - DMA Disable on Reception Error This bit can only be written when the USART is disabled (UE=0). Note: The reception errors are: parity error, framing error or noise error.
Field DDRE writer - DMA Disable on Reception Error This bit can only be written when the USART is disabled (UE=0). Note: The reception errors are: parity error, framing error or noise error.
Field DEM reader - Driver enable mode This bit enables the user to activate the external transceiver control, through the DE signal. This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: If the Driver Enable feature is not supported, this bit is reserved and must be kept at reset value. .
Field DEM writer - Driver enable mode This bit enables the user to activate the external transceiver control, through the DE signal. This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: If the Driver Enable feature is not supported, this bit is reserved and must be kept at reset value. .
Field DEP reader - Driver enable polarity selection This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: If the Driver Enable feature is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field DEP writer - Driver enable polarity selection This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: If the Driver Enable feature is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field DMAR reader - DMA enable receiver This bit is set/reset by software
Field DMAR writer - DMA enable receiver This bit is set/reset by software
Field DMAT reader - DMA enable transmitter This bit is set/reset by software
Field DMAT writer - DMA enable transmitter This bit is set/reset by software
Field EIE reader - Error interrupt enable Error Interrupt Enable Bit is required to enable interrupt generation in case of a framing error, overrun error noise flag or SPI slave underrun error (FEÂ =Â 1 or OREÂ =Â 1 or NEÂ =Â 1 or UDR = 1 in the USART_ISR register).
Field EIE writer - Error interrupt enable Error Interrupt Enable Bit is required to enable interrupt generation in case of a framing error, overrun error noise flag or SPI slave underrun error (FEÂ =Â 1 or OREÂ =Â 1 or NEÂ =Â 1 or UDR = 1 in the USART_ISR register).
Field HDSEL reader - Half-duplex selection Selection of Single-wire Half-duplex mode This bit can only be written when the USART is disabled (UEÂ =Â 0).
Field HDSEL writer - Half-duplex selection Selection of Single-wire Half-duplex mode This bit can only be written when the USART is disabled (UEÂ =Â 0).
Field IREN reader - IrDA mode enable This bit is set and cleared by software. This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: If IrDA mode is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field IREN writer - IrDA mode enable This bit is set and cleared by software. This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: If IrDA mode is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field IRLP reader - IrDA low-power This bit is used for selecting between normal and low-power IrDA modes This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: If IrDA mode is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field IRLP writer - IrDA low-power This bit is used for selecting between normal and low-power IrDA modes This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: If IrDA mode is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field NACK reader - Smartcard NACK enable This bitfield can only be written when the USART is disabled (UEÂ =Â 0). Note: If the USART does not support Smartcard mode, this bit is reserved and must be kept at reset value. Refer to .
Field NACK writer - Smartcard NACK enable This bitfield can only be written when the USART is disabled (UEÂ =Â 0). Note: If the USART does not support Smartcard mode, this bit is reserved and must be kept at reset value. Refer to .
Field ONEBIT reader - One sample bit method enable This bit enables the user to select the sample method. When the one sample bit method is selected the noise detection flag (NE) is disabled. This bit can only be written when the USART is disabled (UEÂ =Â 0).
Field ONEBIT writer - One sample bit method enable This bit enables the user to select the sample method. When the one sample bit method is selected the noise detection flag (NE) is disabled. This bit can only be written when the USART is disabled (UEÂ =Â 0).
Field OVRDIS reader - Overrun Disable This bit is used to disable the receive overrun detection. the ORE flag is not set and the new received data overwrites the previous content of the USART_RDR register. When FIFO mode is enabled, the RXFIFO is bypassed and data is written directly in USART_RDR register. Even when FIFO management is enabled, the RXNE flag is to be used. This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: This control bit enables checking the communication flow w/o reading the data
Field OVRDIS writer - Overrun Disable This bit is used to disable the receive overrun detection. the ORE flag is not set and the new received data overwrites the previous content of the USART_RDR register. When FIFO mode is enabled, the RXFIFO is bypassed and data is written directly in USART_RDR register. Even when FIFO management is enabled, the RXNE flag is to be used. This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: This control bit enables checking the communication flow w/o reading the data
Field RTSE reader - RTS enable This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: If the hardware flow control feature is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field RTSE writer - RTS enable This bit can only be written when the USART is disabled (UEÂ =Â 0). Note: If the hardware flow control feature is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field RXFTCFG reader - Receive FIFO threshold configuration Remaining combinations: Reserved
Field RXFTCFG writer - Receive FIFO threshold configuration Remaining combinations: Reserved
Field RXFTIE reader - RXFIFO threshold interrupt enable This bit is set and cleared by software.
Field RXFTIE writer - RXFIFO threshold interrupt enable This bit is set and cleared by software.
Field SCARCNT reader - Smartcard auto-retry count This bitfield specifies the number of retries for transmission and reception in Smartcard mode. In transmission mode, it specifies the number of automatic retransmission retries, before generating a transmission error (FE bit set). In reception mode, it specifies the number or erroneous reception trials, before generating a reception error (RXNE/RXFNE and PE bits set). This bitfield must be programmed only when the USART is disabled (UEÂ =Â 0). When the USART is enabled (UEÂ =Â 1), this bitfield may only be written to 0x0, in order to stop retransmission. Note: If Smartcard mode is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field SCARCNT writer - Smartcard auto-retry count This bitfield specifies the number of retries for transmission and reception in Smartcard mode. In transmission mode, it specifies the number of automatic retransmission retries, before generating a transmission error (FE bit set). In reception mode, it specifies the number or erroneous reception trials, before generating a reception error (RXNE/RXFNE and PE bits set). This bitfield must be programmed only when the USART is disabled (UEÂ =Â 0). When the USART is enabled (UEÂ =Â 1), this bitfield may only be written to 0x0, in order to stop retransmission. Note: If Smartcard mode is not supported, this bit is reserved and must be kept at reset value. Refer to .
Field SCEN reader - Smartcard mode enable This bit is used for enabling Smartcard mode. This bitfield can only be written when the USART is disabled (UEÂ =Â 0). Note: If the USART does not support Smartcard mode, this bit is reserved and must be kept at reset value. Refer to .
Field SCEN writer - Smartcard mode enable This bit is used for enabling Smartcard mode. This bitfield can only be written when the USART is disabled (UEÂ =Â 0). Note: If the USART does not support Smartcard mode, this bit is reserved and must be kept at reset value. Refer to .
Field TCBGTIE reader - Transmission Complete before guard time, interrupt enable This bit is set and cleared by software. Note: If the USART does not support the Smartcard mode, this bit is reserved and must be kept at reset value. Refer to .
Field TCBGTIE writer - Transmission Complete before guard time, interrupt enable This bit is set and cleared by software. Note: If the USART does not support the Smartcard mode, this bit is reserved and must be kept at reset value. Refer to .
Field TXFTCFG reader - TXFIFO threshold configuration Remaining combinations: Reserved
Field TXFTCFG writer - TXFIFO threshold configuration Remaining combinations: Reserved
Field TXFTIE reader - TXFIFO threshold interrupt enable This bit is set and cleared by software.
Field TXFTIE writer - TXFIFO threshold interrupt enable This bit is set and cleared by software.
Field WUFIE reader - Wakeup from low-power mode interrupt enable This bit is set and cleared by software. Note: WUFIE must be set before entering in low-power mode. If the USART does not support the wakeup from Stop feature, this bit is reserved and must be kept at reset value. Refer to page 835.
Field WUFIE writer - Wakeup from low-power mode interrupt enable This bit is set and cleared by software. Note: WUFIE must be set before entering in low-power mode. If the USART does not support the wakeup from Stop feature, this bit is reserved and must be kept at reset value. Refer to page 835.
Field WUS reader - Wakeup from low-power mode interrupt flag selection This bitfield specifies the event which activates the WUF (Wakeup from low-power mode flag). This bitfield can only be written when the USART is disabled (UE = 0). If the USART does not support the wakeup from Stop feature, this bit is reserved and must be kept at reset value. Refer to page 835.
Field WUS writer - Wakeup from low-power mode interrupt flag selection This bitfield specifies the event which activates the WUF (Wakeup from low-power mode flag). This bitfield can only be written when the USART is disabled (UE = 0). If the USART does not support the wakeup from Stop feature, this bit is reserved and must be kept at reset value. Refer to page 835.