Module stm32_hal2::pac::sai1::ch::cr2

Configuration register 2

Structs

• CR2_SPEC
  Configuration register 2
• R
  Register CR2 reader
• W
  Register CR2 writer

Enums

• COMP_A
  Companding mode. These bits are set and cleared by software. The -Law and the A-Law log are a part of the CCITT G.711 recommendation, the type of complement that will be used depends on CPL bit. The data expansion or data compression are determined by the state of bit MODE[0]. The data compression is applied if the audio block is configured as a transmitter. The data expansion is automatically applied when the audio block is configured as a receiver. Refer to Section: Companding mode for more details. Note: Companding mode is applicable only when TDM is selected.
• CPL_A
  Complement bit. This bit is set and cleared by software. It defines the type of complement to be used for companding mode Note: This bit has effect only when the companding mode is -Law algorithm or A-Law algorithm.
• FFLUSH_AW
  FIFO flush. This bit is set by software. It is always read as 0. This bit should be configured when the SAI is disabled.
• FTH_A
  FIFO threshold. This bit is set and cleared by software.
• MUTEVAL_A
  Mute value. This bit is set and cleared by software.It must be written before enabling the audio block: SAIXEN. This bit is meaningful only when the audio block operates as a transmitter, the number of slots is lower or equal to 2 and the MUTE bit is set. If more slots are declared, the bit value sent during the transmission in mute mode is equal to 0, whatever the value of MUTEVAL. if the number of slot is lower or equal to 2 and MUTEVAL = 1, the MUTE value transmitted for each slot is the one sent during the previous frame. Refer to Section: Mute mode for more details. Note: This bit is meaningless and should not be used for SPDIF audio blocks.
• MUTE_A
  Mute. This bit is set and cleared by software. It is meaningful only when the audio block operates as a transmitter. The MUTE value is linked to value of MUTEVAL if the number of slots is lower or equal to 2, or equal to 0 if it is greater than 2. Refer to Section: Mute mode for more details. Note: This bit is meaningless and should not be used for SPDIF audio blocks.

Type Aliases

• COMP_R
  Field COMP reader - Companding mode. These bits are set and cleared by software. The -Law and the A-Law log are a part of the CCITT G.711 recommendation, the type of complement that will be used depends on CPL bit. The data expansion or data compression are determined by the state of bit MODE[0]. The data compression is applied if the audio block is configured as a transmitter. The data expansion is automatically applied when the audio block is configured as a receiver. Refer to Section: Companding mode for more details. Note: Companding mode is applicable only when TDM is selected.
• COMP_W
  Field COMP writer - Companding mode. These bits are set and cleared by software. The -Law and the A-Law log are a part of the CCITT G.711 recommendation, the type of complement that will be used depends on CPL bit. The data expansion or data compression are determined by the state of bit MODE[0]. The data compression is applied if the audio block is configured as a transmitter. The data expansion is automatically applied when the audio block is configured as a receiver. Refer to Section: Companding mode for more details. Note: Companding mode is applicable only when TDM is selected.
• CPL_R
  Field CPL reader - Complement bit. This bit is set and cleared by software. It defines the type of complement to be used for companding mode Note: This bit has effect only when the companding mode is -Law algorithm or A-Law algorithm.
• CPL_W
  Field CPL writer - Complement bit. This bit is set and cleared by software. It defines the type of complement to be used for companding mode Note: This bit has effect only when the companding mode is -Law algorithm or A-Law algorithm.
• FFLUSH_W
  Field FFLUSH writer - FIFO flush. This bit is set by software. It is always read as 0. This bit should be configured when the SAI is disabled.
• FTH_R
  Field FTH reader - FIFO threshold. This bit is set and cleared by software.
• FTH_W
  Field FTH writer - FIFO threshold. This bit is set and cleared by software.
• MUTECNT_R
  Field MUTECNT reader - Mute counter. These bits are set and cleared by software. They are used only in reception mode. The value set in these bits is compared to the number of consecutive mute frames detected in reception. When the number of mute frames is equal to this value, the flag MUTEDET will be set and an interrupt will be generated if bit MUTEDETIE is set. Refer to Section: Mute mode for more details.
• MUTECNT_W
  Field MUTECNT writer - Mute counter. These bits are set and cleared by software. They are used only in reception mode. The value set in these bits is compared to the number of consecutive mute frames detected in reception. When the number of mute frames is equal to this value, the flag MUTEDET will be set and an interrupt will be generated if bit MUTEDETIE is set. Refer to Section: Mute mode for more details.
• MUTEVAL_R
  Field MUTEVAL reader - Mute value. This bit is set and cleared by software.It must be written before enabling the audio block: SAIXEN. This bit is meaningful only when the audio block operates as a transmitter, the number of slots is lower or equal to 2 and the MUTE bit is set. If more slots are declared, the bit value sent during the transmission in mute mode is equal to 0, whatever the value of MUTEVAL. if the number of slot is lower or equal to 2 and MUTEVAL = 1, the MUTE value transmitted for each slot is the one sent during the previous frame. Refer to Section: Mute mode for more details. Note: This bit is meaningless and should not be used for SPDIF audio blocks.
• MUTEVAL_W
  Field MUTEVAL writer - Mute value. This bit is set and cleared by software.It must be written before enabling the audio block: SAIXEN. This bit is meaningful only when the audio block operates as a transmitter, the number of slots is lower or equal to 2 and the MUTE bit is set. If more slots are declared, the bit value sent during the transmission in mute mode is equal to 0, whatever the value of MUTEVAL. if the number of slot is lower or equal to 2 and MUTEVAL = 1, the MUTE value transmitted for each slot is the one sent during the previous frame. Refer to Section: Mute mode for more details. Note: This bit is meaningless and should not be used for SPDIF audio blocks.
• MUTE_R
  Field MUTE reader - Mute. This bit is set and cleared by software. It is meaningful only when the audio block operates as a transmitter. The MUTE value is linked to value of MUTEVAL if the number of slots is lower or equal to 2, or equal to 0 if it is greater than 2. Refer to Section: Mute mode for more details. Note: This bit is meaningless and should not be used for SPDIF audio blocks.
• MUTE_W
  Field MUTE writer - Mute. This bit is set and cleared by software. It is meaningful only when the audio block operates as a transmitter. The MUTE value is linked to value of MUTEVAL if the number of slots is lower or equal to 2, or equal to 0 if it is greater than 2. Refer to Section: Mute mode for more details. Note: This bit is meaningless and should not be used for SPDIF audio blocks.
• TRIS_R
  Field TRIS reader - Tristate management on data line. This bit is set and cleared by software. It is meaningful only if the audio block is configured as a transmitter. This bit is not used when the audio block is configured in SPDIF mode. It should be configured when SAI is disabled. Refer to Section: Output data line management on an inactive slot for more details.
• TRIS_W
  Field TRIS writer - Tristate management on data line. This bit is set and cleared by software. It is meaningful only if the audio block is configured as a transmitter. This bit is not used when the audio block is configured in SPDIF mode. It should be configured when SAI is disabled. Refer to Section: Output data line management on an inactive slot for more details.