1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
#[doc = "Reader of register TIMEOUT"] pub type R = crate::R<u32, super::TIMEOUT>; #[doc = "Writer for register TIMEOUT"] pub type W = crate::W<u32, super::TIMEOUT>; #[doc = "Register TIMEOUT `reset()`'s with value 0xffff"] impl crate::ResetValue for super::TIMEOUT { type Type = u32; #[inline(always)] fn reset_value() -> Self::Type { 0xffff } } #[doc = "Reader of field `TOMIN`"] pub type TOMIN_R = crate::R<u8, u8>; #[doc = "Write proxy for field `TOMIN`"] pub struct TOMIN_W<'a> { w: &'a mut W, } impl<'a> TOMIN_W<'a> { #[doc = r"Writes raw bits to the field"] #[inline(always)] pub unsafe fn bits(self, value: u8) -> &'a mut W { self.w.bits = (self.w.bits & !0x0f) | ((value as u32) & 0x0f); self.w } } #[doc = "Reader of field `TO`"] pub type TO_R = crate::R<u16, u16>; #[doc = "Write proxy for field `TO`"] pub struct TO_W<'a> { w: &'a mut W, } impl<'a> TO_W<'a> { #[doc = r"Writes raw bits to the field"] #[inline(always)] pub unsafe fn bits(self, value: u16) -> &'a mut W { self.w.bits = (self.w.bits & !(0x0fff << 4)) | (((value as u32) & 0x0fff) << 4); self.w } } impl R { #[doc = "Bits 0:3 - Time-out time value, bottom four bits. These are hard-wired to 0xF. This gives a minimum time-out of 16 I2C function clocks and also a time-out resolution of 16 I2C function clocks."] #[inline(always)] pub fn tomin(&self) -> TOMIN_R { TOMIN_R::new((self.bits & 0x0f) as u8) } #[doc = "Bits 4:15 - Time-out time value. Specifies the time-out interval value in increments of 16 I 2C function clocks, as defined by the CLKDIV register. To change this value while I2C is in operation, disable all time-outs, write a new value to TIMEOUT, then re-enable time-outs. 0x000 = A time-out will occur after 16 counts of the I2C function clock. 0x001 = A time-out will occur after 32 counts of the I2C function clock. 0xFFF = A time-out will occur after 65,536 counts of the I2C function clock."] #[inline(always)] pub fn to(&self) -> TO_R { TO_R::new(((self.bits >> 4) & 0x0fff) as u16) } } impl W { #[doc = "Bits 0:3 - Time-out time value, bottom four bits. These are hard-wired to 0xF. This gives a minimum time-out of 16 I2C function clocks and also a time-out resolution of 16 I2C function clocks."] #[inline(always)] pub fn tomin(&mut self) -> TOMIN_W { TOMIN_W { w: self } } #[doc = "Bits 4:15 - Time-out time value. Specifies the time-out interval value in increments of 16 I 2C function clocks, as defined by the CLKDIV register. To change this value while I2C is in operation, disable all time-outs, write a new value to TIMEOUT, then re-enable time-outs. 0x000 = A time-out will occur after 16 counts of the I2C function clock. 0x001 = A time-out will occur after 32 counts of the I2C function clock. 0xFFF = A time-out will occur after 65,536 counts of the I2C function clock."] #[inline(always)] pub fn to(&mut self) -> TO_W { TO_W { w: self } } }